Scribe logoScribeNotes & practice
Sign inStart free
  1. Notes
  2. ›AP Physics 2
  3. ›12 Magnetism and Electromagnetism
  4. ›12.4 Electromagnetic induction

AP Physics 2 · Unit 12 · Magnetism and Electromagnetism

12.4 Electromagnetic induction

Explain how a changing magnetic flux induces an emf and current, apply Faraday’s law, and use Lenz’s law to find the direction of the induced current.

  • 4 min read
  • 5 parts
  • 10 questions
  • Draft
Start a Quick 5 on this topic→Jump to the 10 questions
1/5A changing magnetic field can drive a current
  1. 1A changing magnetic field can drive a current
  2. 2Magnetic flux measures how much field passes through a loop
  3. 3Faraday’s law links induced emf to the rate of change of flux
  4. 4Lenz’s law gives the direction of the induced current
  5. 5Motional emf and other factors set the size of the emf
  6. Check your recall
  7. Practice: 10 questions
1

Part 1 of 5: A changing magnetic field can drive a current

Push a bar magnet into a coil of wire connected to a sensitive meter. The needle jumps while the magnet moves. It returns to zero when the magnet stops, even though the magnet is still inside the coil.

The circuit has no battery, so something else must push the charges. The moving magnet changes the magnetic field through the coil. That change creates an induced emf around the loop. In a closed circuit, the emf drives an induced current.

Common mistake

A strong magnet at rest inside a coil produces no current. The change in the field is what matters, not the field strength alone.

Key term

induced emf

The induced emf is the emf, in volts (V), produced around a conducting loop by a changing magnetic field through the loop.

Part 1 done

2

Part 2 of 5: Magnetic flux measures how much field passes through a loop

Hold a hoop in falling rain. Held flat, it catches the most drops. Tilted edge-on, it catches none.

Field lines passing through a loop work the same way. Magnetic flux counts how much field passes through the area. For a flat loop in a uniform field, ΦB=BAcos⁡θ\Phi_B = BA\cos\thetaΦB​=BAcosθ. Here BBB is the field strength and AAA is the loop’s area. The angle θ\thetaθ lies between the field and the line perpendicular to the loop.

The flux changes when any one of these changes:

  • the field strength BBB
  • the area AAA of the loop
  • the angle θ\thetaθ between the field and the perpendicular

Key term

magnetic flux

The magnetic flux ΦB=BAcos⁡θ\Phi_B=BA\cos\thetaΦB​=BAcosθ through a flat loop in a uniform field is measured in webers (Wb), where 1 Wb=1 T m21\,\mathrm{Wb}=1\,\mathrm{T\,m^2}1Wb=1Tm2.

Part 2 done

Quick check

One question on the part you just read

Easy

Identify what must happen for an emf to be induced in a loop.
Show answer and explanation

Answer: A · Worked explanation

An emf is induced only when the magnetic flux through the loop changes. Faraday’s law contains the rate of change of flux, so a steady flux gives zero emf. A strong but constant field does not work because a steady field gives no change in flux, and so no induced emf.
3

Part 3 of 5: Faraday’s law links induced emf to the rate of change of flux

Now we can say how large the emf is. A faster change in flux induces a larger emf. Faraday’s law puts this exactly. For a coil of NNN turns, the average emf is ε=−NΔΦBΔt\varepsilon = -N\frac{\Delta\Phi_B}{\Delta t}ε=−NΔtΔΦB​​.

Each turn contributes its own emf, so NNN turns multiply the result by NNN. The minus sign records the direction, which the next section covers. For sizes only, use ∣ε∣=N∣ΔΦB∣Δt|\varepsilon| = N\frac{|\Delta\Phi_B|}{\Delta t}∣ε∣=NΔt∣ΔΦB​∣​.

Worked example

Average emf in a coil

A coil has 50 turns and an area of 0.020 m20.020\,\mathrm{m^2}0.020m2. A field along the coil’s perpendicular rises from 0.20 T to 0.60 T in 0.50 s. Determine the magnitude of the average emf.
  1. 1
    Flux is ΦB=BAcos⁡θ\Phi_B=BA\cos\thetaΦB​=BAcosθ with θ=0∘\theta=0^{\circ}θ=0∘, so ΦB=BA\Phi_B=BAΦB​=BA.
  2. 2
    Initial flux: (0.20 T)(0.020 m2)=0.0040 T m2(0.20\,\mathrm{T})(0.020\,\mathrm{m^2})=0.0040\,\mathrm{T\,m^2}(0.20T)(0.020m2)=0.0040Tm2. Final flux: (0.60 T)(0.020 m2)=0.012 T m2(0.60\,\mathrm{T})(0.020\,\mathrm{m^2})=0.012\,\mathrm{T\,m^2}(0.60T)(0.020m2)=0.012Tm2.
  3. 3
    Change in flux: ΔΦB=0.012−0.0040=0.0080 T m2\Delta\Phi_B=0.012-0.0040=0.0080\,\mathrm{T\,m^2}ΔΦB​=0.012−0.0040=0.0080Tm2.
  4. 4
    ∣ε∣=N∣ΔΦB∣Δt=50 0.0080 T m20.50 s=0.80 V|\varepsilon|=N\frac{|\Delta\Phi_B|}{\Delta t}=50\,\frac{0.0080\,\mathrm{T\,m^2}}{0.50\,\mathrm{s}}=0.80\,\mathrm{V}∣ε∣=NΔt∣ΔΦB​∣​=500.50s0.0080Tm2​=0.80V.

Answer: The magnitude of the average emf is 0.80 V0.80\,\mathrm{V}0.80V.

Exam tip

Find the change in flux as final minus initial, and check the angle. Only the change in flux enters the law, never the flux at one moment.

Key term

Faraday’s law

Faraday’s law is the statement that the average emf induced in a coil of NNN turns equals −NΔΦBΔt-N\frac{\Delta\Phi_B}{\Delta t}−NΔtΔΦB​​.

Part 3 done

4

Part 4 of 5: Lenz’s law gives the direction of the induced current

The minus sign in Faraday’s law carries a physical rule. Lenz’s law says the induced current produces a magnetic field that opposes the change in flux. It opposes the change, not the flux itself.

Bring a magnet’s north pole toward a loop. The flux grows, so the loop makes a field pointing back toward the magnet. Its near face acts like a north pole and pushes the magnet away.

Common mistake

The induced field does not always point opposite to the original field. If the flux is decreasing, the induced field points the same way to oppose the loss.

To find the direction of the induced current:

  • Find the direction of the original field.
  • Decide whether its flux is increasing or decreasing.
  • Choose the induced field: opposite if increasing, the same if decreasing.
  • Use the right-hand rule to find the current.
Go deeperWhy the induced field must oppose the change

Suppose the induced field helped the change instead. Pushing a magnet toward a loop would make the loop pull the magnet in harder. The magnet would speed up and the current would grow, creating energy from nothing.

Opposition prevents this. You must do work to push the magnet against the repulsion. That work becomes the electrical energy of the induced current, so Lenz’s law is conservation of energy at work.

Key term

Lenz’s law

Lenz’s law is the rule that an induced current flows in the direction that produces a field opposing the change in flux that caused it.

Part 4 done

Quick check

One question on the part you just read

Easy

Magnetic flux through a loop can be measured in which unit?
Show answer and explanation

Answer: A · Worked explanation

Flux is ΦB=BAcos⁡θ\Phi_B=BA\cos\thetaΦB​=BAcosθ, the product of field strength in teslas and area in square meters. The unit is therefore T m2\mathrm{T\,m^2}Tm2, which is called the weber. Dividing by area or length instead of multiplying gives units such as T/m2\mathrm{T/m^2}T/m2, which do not describe flux.
5

Part 5 of 5: Motional emf and other factors set the size of the emf

Faraday’s law also explains a rod sliding along two rails in a magnetic field. As the rod moves, the loop’s area changes, so the flux changes. Take a rod of length ℓ\ellℓ moving at speed vvv perpendicular to a field BBB. Its motional emf is ε=Bℓv\varepsilon = B\ell vε=Bℓv.

Worked example

Emf and current from a sliding rod

A rod of length 0.40 m slides at 3.0 m/s perpendicular to a 0.25 T field. The circuit has a total resistance of 0.60 Ω0.60\,\Omega0.60Ω. Determine the emf and the current.
  1. 1
    Use the motional emf ε=Bℓv\varepsilon=B\ell vε=Bℓv.
  2. 2
    Substitute: ε=(0.25 T)(0.40 m)(3.0 m/s)=0.30 V\varepsilon=(0.25\,\mathrm{T})(0.40\,\mathrm{m})(3.0\,\mathrm{m/s})=0.30\,\mathrm{V}ε=(0.25T)(0.40m)(3.0m/s)=0.30V.
  3. 3
    Use I=εR=0.30 V0.60 Ω=0.50 AI=\frac{\varepsilon}{R}=\frac{0.30\,\mathrm{V}}{0.60\,\Omega}=0.50\,\mathrm{A}I=Rε​=0.60Ω0.30V​=0.50A.

Answer: The emf is 0.30 V0.30\,\mathrm{V}0.30V and the current is 0.50 A0.50\,\mathrm{A}0.50A.

To raise the induced emf, change the setup in one of these ways:

  • Use a stronger field.
  • Move the magnet or loop faster.
  • Add more turns to the coil.
  • Change the area or angle more quickly.

Exam tip

Find the size of the emf from Faraday’s law and the direction from Lenz’s law. A full answer about an induced current gives both.

Key term

motional emf

The motional emf is the emf ε=Bℓv\varepsilon=B\ell vε=Bℓv induced in a conductor of length ℓ\ellℓ moving at speed vvv perpendicular to a uniform field BBB.

Note read

Check your recall[13 marks]

6 written questions. Answer each one in your head or on paper, then open the mark scheme.

  1. 1.Explain[2 marks]

    Explain why a bar magnet at rest inside a coil produces no current, but a moving magnet does.

    Show mark schemeHide mark scheme

    Model answer

    An emf is induced only when the magnetic flux through the coil changes. A magnet at rest gives a constant flux, while a moving magnet changes the flux.

    • 1 mark for stating that an emf is induced only when the flux through the coil changes
    • 1 mark for explaining that a resting magnet gives constant flux but a moving magnet changes it
  2. 2.Calculate[3 marks]

    Calculate the magnitude of the average emf induced in a 200-turn coil when the flux through it falls from 0.0050 T m20.0050\,\mathrm{T\,m^2}0.0050Tm2 to 0.0010 T m20.0010\,\mathrm{T\,m^2}0.0010Tm2 in 0.020 s0.020\,\mathrm{s}0.020s.

    Show mark schemeHide mark scheme

    Model answer

    ΔΦB=0.0010−0.0050=−0.0040 T m2\Delta\Phi_B=0.0010-0.0050=-0.0040\,\mathrm{T\,m^2}ΔΦB​=0.0010−0.0050=−0.0040Tm2, so ∣ε∣=200 0.00400.020=40 V|\varepsilon|=200\,\frac{0.0040}{0.020}=40\,\mathrm{V}∣ε∣=2000.0200.0040​=40V.

    • 1 mark for using ∣ε∣=N∣ΔΦB∣/Δt|\varepsilon|=N|\Delta\Phi_B|/\Delta t∣ε∣=N∣ΔΦB​∣/Δt
    • 1 mark for finding the change in flux as 0.0040 T m20.0040\,\mathrm{T\,m^2}0.0040Tm2
    • 1 mark for obtaining 40 V40\,\mathrm{V}40V
  3. 3.Determine[2 marks]

    Determine the direction of the field created by the induced current when a magnetic field pointing into a loop decreases in strength.

    Show mark schemeHide mark scheme

    Model answer

    The flux into the loop is decreasing. The induced field opposes this decrease, so it points into the loop, the same direction as the original field.

    • 1 mark for recognizing that the flux is decreasing and the induced field opposes that change
    • 1 mark for stating that the induced field points into the loop
  4. 4.Predict[2 marks]

    Predict how the motional emf of a sliding rod changes if its speed doubles and the field strength is halved.

    Show mark schemeHide mark scheme

    Model answer

    The emf is unchanged. Since ε=Bℓv\varepsilon=B\ell vε=Bℓv, halving BBB and doubling vvv leaves the product BvBvBv the same.

    • 1 mark for predicting that the emf stays the same
    • 1 mark for using ε=Bℓv\varepsilon=B\ell vε=Bℓv to show the factors cancel
  5. 5.Identify[1 mark]

    Identify the angle between the field and the perpendicular to a loop at which the flux through it is zero.

    Show mark schemeHide mark scheme

    Model answer

    The flux is zero when the angle is 90∘90^{\circ}90∘, because cos⁡90∘=0\cos 90^{\circ}=0cos90∘=0.

    • 1 mark for stating 90∘90^{\circ}90∘
  6. 6.Describe[3 marks]

    Describe three ways to increase the average emf induced in a coil.

    Show mark schemeHide mark scheme

    Model answer

    Change the flux more quickly, for example by moving the magnet faster. Use a stronger field so the flux changes by more. Add more turns to the coil.

    • 1 mark for describing a faster change in flux
    • 1 mark for describing a stronger field or larger area change
    • 1 mark for describing more turns in the coil

Practice this topic

10 quick-fire multiple-choice questions, easy to hard. Tap an answer to see if you're right and the worked explanation. (The written questions with mark schemes are under “Check your recall” above.)

0 right0 of 10 answered

Includes the 2 quick checks in the note above.

3.

Easy·Identify[1 mark]

Identify what Lenz’s law says about the field produced by an induced current.
Show answer and explanation

Answer: B · Worked explanation

Lenz’s law says the induced current makes a field that opposes the change in flux. It is not always opposite to the original field. If the original flux is decreasing, the induced field points the same way to oppose that loss. A field that added to the change would create energy from nothing.
4.

Medium·Calculate[2 marks]

A coil of 100 turns has a flux that falls from 0.030 T m20.030\,\mathrm{T\,m^2}0.030Tm2 to 0.010 T m20.010\,\mathrm{T\,m^2}0.010Tm2 in 0.40 s. Calculate the magnitude of the average induced emf.
Show answer and explanation

Answer: D · Worked explanation

The change in flux is 0.020 T m20.020\,\mathrm{T\,m^2}0.020Tm2, found as the difference between the final and initial values. Then ∣ε∣=N∣ΔΦB∣Δt=100×0.020 T m20.40 s=5.0 V|\varepsilon|=N\frac{|\Delta\Phi_B|}{\Delta t}=100\times\frac{0.020\,\mathrm{T\,m^2}}{0.40\,\mathrm{s}}=5.0\,\mathrm{V}∣ε∣=NΔt∣ΔΦB​∣​=100×0.40s0.020Tm2​=5.0V. The value 0.050 V0.050\,\mathrm{V}0.050V comes from forgetting the 100 turns. The value 2.5 V2.5\,\mathrm{V}2.5V comes from using only the final flux instead of the change.
5.

Medium·Calculate[2 marks]

A rod of length 0.50 m moves at 4.0 m/s perpendicular to a uniform 0.30 T field. Calculate the motional emf.
Show answer and explanation

Answer: D · Worked explanation

Use ε=Bℓv\varepsilon=B\ell vε=Bℓv with the field, length, and speed given. This gives (0.30 T)(0.50 m)(4.0 m/s)=0.60 V(0.30\,\mathrm{T})(0.50\,\mathrm{m})(4.0\,\mathrm{m/s})=0.60\,\mathrm{V}(0.30T)(0.50m)(4.0m/s)=0.60V. The value 1.2 V1.2\,\mathrm{V}1.2V comes from leaving out the length of the rod. The value 2.4 V2.4\,\mathrm{V}2.4V comes from dividing by the length instead of multiplying by it, which does not match the formula.
6.

Medium·Calculate[2 marks]

A flat loop of area 0.050 m20.050\,\mathrm{m^2}0.050m2 sits in a uniform 0.40 T field. The angle between the field and the perpendicular to the loop is 60∘60^{\circ}60∘. Calculate the flux through the loop.
Show answer and explanation

Answer: B · Worked explanation

Use ΦB=BAcos⁡θ\Phi_B=BA\cos\thetaΦB​=BAcosθ with θ=60∘\theta=60^{\circ}θ=60∘ measured from the perpendicular to the loop. This gives (0.40 T)(0.050 m2)(0.50)=0.010 T m2(0.40\,\mathrm{T})(0.050\,\mathrm{m^2})(0.50)=0.010\,\mathrm{T\,m^2}(0.40T)(0.050m2)(0.50)=0.010Tm2. The value 0.017 T m20.017\,\mathrm{T\,m^2}0.017Tm2 comes from using the sine of the angle. The value 0.020 T m20.020\,\mathrm{T\,m^2}0.020Tm2 comes from ignoring the angle entirely. Only the component of the field along the perpendicular counts toward the flux.
7.

Medium·Predict[1 mark]

The north pole of a bar magnet is pulled away from a loop. Predict how the face of the loop nearest the magnet behaves.
Show answer and explanation

Answer: B · Worked explanation

As the magnet leaves, the flux from it decreases. The induced field points the same way as the magnet’s field to oppose the loss, so the near face acts like a south pole. That pole attracts the receding north pole and resists the motion. A north pole there would help the magnet leave, which Lenz’s law forbids.
8.

Hard·Determine[2 marks]

A coil of 20 turns and area 0.040 m20.040\,\mathrm{m^2}0.040m2 is in a field along its perpendicular. The field changes from +0.50 T to -0.50 T in 0.10 s. Determine the magnitude of the average emf.
Show answer and explanation

Answer: D · Worked explanation

The field reverses, so ΔB=−1.00 T\Delta B=-1.00\,\mathrm{T}ΔB=−1.00T. The change in flux has magnitude ∣ΔΦB∣=(1.00 T)(0.040 m2)=0.040 T m2|\Delta\Phi_B|=(1.00\,\mathrm{T})(0.040\,\mathrm{m^2})=0.040\,\mathrm{T\,m^2}∣ΔΦB​∣=(1.00T)(0.040m2)=0.040Tm2. Then ∣ε∣=20×0.0400.10=8.0 V|\varepsilon|=20\times\frac{0.040}{0.10}=8.0\,\mathrm{V}∣ε∣=20×0.100.040​=8.0V. The value 4.0 V4.0\,\mathrm{V}4.0V treats the change as only 0.50 T. The value 0 V0\,\mathrm{V}0V wrongly assumes equal field sizes mean no change. Reversing the field makes the change twice as large as either field alone.
9.

Hard·Predict[2 marks]

A rod slides on rails. Its speed doubles, and the total resistance of the circuit also doubles. Predict what happens to the induced current.
Show answer and explanation

Answer: C · Worked explanation

The emf is ε=Bℓv\varepsilon=B\ell vε=Bℓv, so doubling vvv doubles the emf. The current is I=εRI=\frac{\varepsilon}{R}I=Rε​, so doubling both the emf and the resistance leaves the current unchanged. The answer that the current doubles comes from forgetting that the resistance also changed.
10.

Hard·Determine[2 marks]

A magnetic field points out of the page through a flat loop and increases in strength. Determine the induced current as seen by someone looking at the page.
Show answer and explanation

Answer: B · Worked explanation

The flux out of the page is increasing, so the induced field points into the page to oppose the increase. By the right-hand rule, a clockwise current produces a field into the page inside the loop. A counterclockwise current would give a field out of the page and add to the increase, which Lenz’s law rules out.

Keep going

Next topic13.1 ReflectionPrevious topic12.3 Magnetic fields of current-carrying wires

More in Unit 12 · Magnetism and Electromagnetism

  1. 12.1Magnetic fieldsNotes · 10 questions
  2. 12.2Magnetism and moving chargesNotes · 10 questions
  3. 12.3Magnetic fields of current-carrying wiresNotes · 10 questions
  4. 12.4Electromagnetic inductionNotes · 10 questions

All AP Physics 2 topics →

Draft: written by Scribe and checked automatically, not yet by a subject reviewer.

Practice questions are original, written by Scribe and checked automatically for correctness.

Topic codes follow the official numbering. Not endorsed by College Board or any exam board.

On this page

0/5 read

  1. 1A changing magnetic field can drive a current
  2. 2Magnetic flux measures how much field passes through a loop
  3. 3Faraday’s law links induced emf to the rate of change of flux
  4. 4Lenz’s law gives the direction of the induced current
  5. 5Motional emf and other factors set the size of the emf
  6. Check your recall
  7. Practice: 10 questions
All coursesScribeHow it worksPricingPrivacyTerms

Notes and questions are written by Scribe in our own words. Topic codes follow the official course numbering so you can find your place. Not produced or endorsed by the IB, College Board, AQA, OCR, Pearson Edexcel or any exam board.

© 2026 Scribe