IB Mathematics: Analysis and Approaches · Topic 5 · Calculus
5.11 Definite integrals and areas
Evaluate definite integrals, interpret them as areas under curves, and find the area between two curves.
1/5A definite integral measures accumulated change between two limits
- A definite integral measures accumulated change between two limits
- Evaluation substitutes the limits into an antiderivative
- Regions above the axis count positive and below count negative
- The area between two curves uses upper minus lower
- Integrating a rate gives the total change in a quantity
- Check your recall
- Practice: 10 questions
Part 1 of 5: A definite integral measures accumulated change between two limits
A tap fills a bath, and the rate of flow changes with time. To find the water gained, add up the flow over every moment. The definite integral does exactly this. Its limits of integration are the start and end values, written and .
If is an antiderivative of , then . We often write this as . No constant appears, because it cancels in the subtraction.
The integrand can be any function with an antiderivative. The limits fix the range over which the change is added up.
The answer is a single number. An indefinite integral, by contrast, gives a family of functions.
Key terms · tap one for its definition
rate
A rate is a derivative that measures how a quantity changes with respect to time.
definite integral
A definite integral of a rate over an interval measures its accumulated, signed change.
limits of integration
The limits of integration specify the starting and ending input values of a definite integral.
Part 2 of 5: Evaluation substitutes the limits into an antiderivative
Now that the formula is clear, the method is routine. Find an antiderivative, substitute the upper limit, then subtract the value at the lower limit.
Write the antiderivative in square brackets, with the limits on the right. Use brackets around negative values when substituting.
Worked example
Evaluating a definite integral
- Find an antiderivative: .
- Substitute the limits: and .
- Subtract: .
Answer:
Three properties help. Swapping the limits changes the sign: . Equal limits give . A range can be split: .
These properties are used constantly in area problems, where a range must often be split at a crossing point.

Quick check
One question on the part you just read
Easy
Show answer and explanation
Answer: A · Worked explanation
Part 3 of 5: Regions above the axis count positive and below count negative
The integral is signed, so it need not equal an area. Where , the integral is the area between the curve and the -axis. Where , the integral is negative.
A sketch shows where the curve crosses the axis. A curve that never goes below the axis needs no splitting.
To find the true area, split the range where the curve crosses the axis. Integrate each part, then add the sizes. In symbols, the area is .
Worked example
Area when the curve crosses the axis
- Solve in the range: .
- For : .
- For : .
- Add the sizes: .
Answer: The area is square units. The integral over the whole range is -3.
Key term
area
Area measures the size of a two-dimensional region.
Part 4 of 5: The area between two curves uses upper minus lower
Many regions lie between two curves rather than a curve and the axis. If on , the area is .
The upper curve may change inside the range. If so, split at the crossing and use the correct curve on each part.
The method works wherever the curves lie, even below the -axis. The difference is still positive.
The limits come from each point of intersection, where the curves meet. Find them by solving .
Worked example
Area between a line and a parabola
- Solve : , so and .
- At , the line gives 2 and the parabola gives 0, so the line is the upper curve.
- Integrate: .
- Substitute: .
Answer: The area is square units.
Key term
point of intersection
A point of intersection of two curves is a point whose coordinates satisfy both equations.

Quick check
One question on the part you just read
Easy
Show answer and explanation
Answer: B · Worked explanation
Part 5 of 5: Integrating a rate gives the total change in a quantity
Return to the tap. Its flow rate is the derivative of the volume gained. So is the change in volume between those times.
The same idea applies to any rate. A negative rate means the quantity is falling, which makes that part of the integral negative.
Units come from multiplying the rate by the variable of integration. Here, times minutes gives .
Velocity is the rate of change of position. Integrating velocity therefore gives the change in position.
Worked example
Volume from a flow rate
- Set up: .
- Integrate: .
- Substitute: .
Answer: The tank gains .
Check your recall[14 marks]
6 written questions. Answer each one in your head or on paper, then open the mark scheme.
- 1.State[2 marks]
State how to evaluate when is an antiderivative of .
Show mark schemeHide mark scheme
Model answer
. Substitute the upper limit, then subtract the value at the lower limit.
- 1 mark for writing
- 1 mark for identifying as the upper limit and as the lower limit
- 2.Calculate[2 marks]
Calculate .
Show mark schemeHide mark scheme
Model answer
.
- 1 mark for antiderivative
- 1 mark for substituting the limits to obtain 57
- 3.Explain[2 marks]
Explain why a definite integral can be negative although an area cannot.
Show mark schemeHide mark scheme
Model answer
Where the curve lies below the -axis, the integrand is negative, so that part of the integral is negative. An area is a size and is never negative.
- 1 mark for stating that the curve below the axis gives a negative contribution
- 1 mark for stating that area measures size and is never negative
- 4.Determine[4 marks]
Determine the area enclosed by and .
Show mark schemeHide mark scheme
Model answer
Solving gives and . The parabola is above the line, so area square units.
- 1 mark for finding the limits and
- 1 mark for using upper minus lower:
- 1 mark for finding the antiderivative correctly
- 1 mark for obtaining
- 5.Calculate[2 marks]
Calculate the volume gained between and minutes by a tank filling at .
Show mark schemeHide mark scheme
Model answer
.
- 1 mark for integrating to obtain
- 1 mark for obtaining
- 6.Deduce[2 marks]
Given that , deduce the value of .
Show mark schemeHide mark scheme
Model answer
Swapping the limits changes the sign, so the value is .
- 1 mark for stating that swapping the limits changes the sign
- 1 mark for giving the value

Practice this topic
10 quick-fire multiple-choice questions, easy to hard. Tap an answer to see if you're right and the worked explanation. (The written questions with mark schemes are under “Check your recall” above.)
0 right0 of 10 answered
Includes the 2 quick checks in the note above.
EasyIdentify[1 mark]
Show answer and explanation
Answer: B · Worked explanation
MediumCalculate[2 marks]
Show answer and explanation
Answer: C · Worked explanation
MediumCalculate[2 marks]
Show answer and explanation
Answer: D · Worked explanation
MediumCalculate[2 marks]
Show answer and explanation
Answer: A · Worked explanation
MediumCalculate[2 marks]
Show answer and explanation
Answer: A · Worked explanation
HardCalculate[2 marks]
Show answer and explanation
Answer: D · Worked explanation
HardDetermine[2 marks]
Show answer and explanation
Answer: B · Worked explanation
HardDetermine[2 marks]
Show answer and explanation
Answer: C · Worked explanation