Scribe logoScribeNotes & practice
Sign inStart free
  1. Notes
  2. ›AP Physics 2
  3. ›9 Thermodynamics
  4. ›9.5 Specific heat and thermal conductivity

AP Physics 2 · Unit 9 · Thermodynamics

9.5 Specific heat and thermal conductivity

Use specific heat to calculate temperature changes, compare thermal conductivities of materials, and explain how insulation reduces heat transfer.

  • 4 min read
  • 5 parts
  • 10 questions
  • Draft
Start a Quick 5 on this topic→Jump to the 10 questions
1/5Different materials need different energy for the same warming
  1. 1Different materials need different energy for the same warming
  2. 2Energy transferred equals mass times specific heat times temperature change
  3. 3Conduction moves energy through a material from hot to cold
  4. 4Conduction rate grows with area and temperature difference
  5. 5Good insulation uses low conductivity and added thickness
  6. Check your recall
  7. Practice: 10 questions
1

Part 1 of 5: Different materials need different energy for the same warming

A metal spoon in hot soup warms in seconds. The soup itself changes temperature far more slowly. Equal amounts of energy do not warm every material equally.

The specific heat of a material tells you how much energy it takes to warm it. A large value means the material resists temperature change. Water has a large specific heat, so a lake warms and cools slowly.

Common mistake

Specific heat is a property of the material, not of the sample. A bigger block needs more energy, but its specific heat does not change.

Key term

specific heat

The specific heat ccc of a material is the energy needed to raise 1 kg of it by 1 K, measured in J/(kg K)\mathrm{J/(kg\,K)}J/(kgK).

Part 1 done

2

Part 2 of 5: Energy transferred equals mass times specific heat times temperature change

Now turn that idea into a calculation. The energy QQQ transferred thermally to a sample depends on three things. These are its mass mmm, its specific heat ccc, and its temperature change ΔT\Delta TΔT.

The relationship is Q=mcΔTQ=mc\Delta TQ=mcΔT. Specific heat has units of J/(kg K)\mathrm{J/(kg\,K)}J/(kgK). A change of 1 K equals a change of 1 °C, so either scale gives the same ΔT\Delta TΔT. Because ΔT\Delta TΔT is final minus initial, a cooling sample gives a negative QQQ.

Worked example

Energy needed to warm water

A 2.0 kg sample of water warms from 20 °C to 35 °C. The specific heat of water is 4,186 J/(kg K)4{,}186\,\mathrm{J/(kg\,K)}4,186J/(kgK). Calculate the energy transferred to the water.
  1. 1
    Find the temperature change: ΔT=35∘C−20∘C=15 K\Delta T=35^{\circ}\mathrm{C}-20^{\circ}\mathrm{C}=15\,\mathrm{K}ΔT=35∘C−20∘C=15K.
  2. 2
    Write the equation: Q=mcΔTQ=mc\Delta TQ=mcΔT.
  3. 3
    Substitute: Q=(2.0 kg)(4,186 J/(kg K))(15 K)Q=(2.0\,\mathrm{kg})(4{,}186\,\mathrm{J/(kg\,K)})(15\,\mathrm{K})Q=(2.0kg)(4,186J/(kgK))(15K).
  4. 4
    Evaluate: Q=125,580 JQ=125{,}580\,\mathrm{J}Q=125,580J.

Answer: Q≈1.3×105 JQ\approx1.3\times10^{5}\,\mathrm{J}Q≈1.3×105J

The result is positive because the water gains energy. If the water cooled by the same amount, QQQ would have the same size but a negative sign.

Part 2 done

Quick check

One question on the part you just read

Easy

Identify the SI unit of specific heat.
Show answer and explanation

Answer: B · Worked explanation

Specific heat is energy per kilogram per kelvin, which follows from c=QmΔTc=\frac{Q}{m\Delta T}c=mΔTQ​, so its unit is J/(kg K)\mathrm{J/(kg\,K)}J/(kgK). The unit J/kg\mathrm{J/kg}J/kg leaves out the temperature change. The unit W/(m K)\mathrm{W/(m\,K)}W/(mK) belongs to thermal conductivity, which describes how fast energy conducts, not how much energy a sample absorbs.
3

Part 3 of 5: Conduction moves energy through a material from hot to cold

A metal spoon left in a hot pot soon has a hot handle. Only the tip touches the soup.

This is conduction: energy passes between neighboring particles while the material as a whole stays put. Faster particles in the hot region share energy with slower ones nearby. Net energy flows from higher temperature to lower temperature.

Materials differ in how well they do this. The thermal conductivity kkk measures how readily a material conducts energy. Metals have large values, while wood, foam, and air have small ones.

Approximate thermal conductivities

Materialk (W/(m K))Conduction
Copperabout 400Very well
Glassabout 1Poorly
Woodabout 0.1Very poorly
Still airabout 0.03Extremely poorly
Material
Copper
k (W/(m K))
about 400
Conduction
Very well
Material
Glass
k (W/(m K))
about 1
Conduction
Poorly
Material
Wood
k (W/(m K))
about 0.1
Conduction
Very poorly
Material
Still air
k (W/(m K))
about 0.03
Conduction
Extremely poorly
Go deeperWhy metals conduct so well

In a metal, some electrons are free to move through the whole solid. These electrons carry energy quickly from hot regions to cold ones. They add to the energy passed along by vibrating atoms.

This is also why a metal object feels cold in your hand. It carries energy away from your skin faster than wood does.

Key terms · tap one for its definition

conduction

Conduction is the transfer of energy through a material by interactions between neighboring particles, without bulk motion of the material.

thermal conductivity

The thermal conductivity kkk of a material is the property that sets how fast energy conducts through it, measured in W/(m K)\mathrm{W/(m\,K)}W/(mK).

Part 3 done

4

Part 4 of 5: Conduction rate grows with area and temperature difference

Now consider a flat slab, such as a wall or a window pane, with one face hotter than the other. Energy conducts through it at a steady rate. Four quantities set that rate.

Figure 1. Energy flows from the hotter face to the colder face. The rate depends on the face area, the thickness, and the temperature difference.

The rate of energy transfer is QΔt=kAΔTL\frac{Q}{\Delta t}=\frac{kA\Delta T}{L}ΔtQ​=LkAΔT​, measured in watts, where 1 W=1 J/s1\,\mathrm{W}=1\,\mathrm{J/s}1W=1J/s. Here AAA is the face area, LLL is the thickness, and ΔT\Delta TΔT is the temperature difference across the slab.

  • Doubling AAA doubles the rate.
  • Doubling ΔT\Delta TΔT doubles the rate.
  • Doubling kkk doubles the rate.
  • Doubling LLL halves the rate.

Exam tip

Check units before substituting. Thickness must be in meters, so convert millimeters and centimeters first.

Worked example

Energy flow through a window

A glass window has area 1.5 m21.5\,\mathrm{m^2}1.5m2 and thickness 5.0 mm. Its thermal conductivity is 0.80 W/(m K)0.80\,\mathrm{W/(m\,K)}0.80W/(mK). The inside is at 22 °C and the outside at 12 °C. Calculate the rate of energy transfer.
  1. 1
    Convert the thickness: L=0.0050 mL=0.0050\,\mathrm{m}L=0.0050m. The temperature difference is ΔT=10 K\Delta T=10\,\mathrm{K}ΔT=10K.
  2. 2
    Write the equation: QΔt=kAΔTL\frac{Q}{\Delta t}=\frac{kA\Delta T}{L}ΔtQ​=LkAΔT​.
  3. 3
    Substitute: QΔt=(0.80 W/(m K))(1.5 m2)(10 K)0.0050 m\frac{Q}{\Delta t}=\frac{(0.80\,\mathrm{W/(m\,K)})(1.5\,\mathrm{m^2})(10\,\mathrm{K})}{0.0050\,\mathrm{m}}ΔtQ​=0.0050m(0.80W/(mK))(1.5m2)(10K)​.
  4. 4
    Evaluate: 12 W m0.0050 m=2400 W\frac{12\,\mathrm{W\,m}}{0.0050\,\mathrm{m}}=2400\,\mathrm{W}0.0050m12Wm​=2400W.

Answer: QΔt≈2.4×103 W\frac{Q}{\Delta t}\approx2.4\times10^{3}\,\mathrm{W}ΔtQ​≈2.4×103W

Part 4 done

Quick check

One question on the part you just read

Easy

Identify the material that is the best thermal insulator.
Show answer and explanation

Answer: C · Worked explanation

Still air has a very low thermal conductivity, about 0.03 W/(m K). That makes the conduction rate tiny for a given area, thickness, and temperature difference. Copper and aluminum are tempting because they are common, but they have very large conductivities and are good conductors. Glass conducts poorly compared with metals but far better than still air.
5

Part 5 of 5: Good insulation uses low conductivity and added thickness

A wool coat or a foam cup keeps energy where it is for a while. Each one uses an insulator to slow the transfer.

Look at the rate equation again. The rate falls when kkk is small, when LLL is large, or when AAA is small. Insulation works by changing those quantities.

Many insulators trap air in tiny pockets, as foam, fiber, and double-glazed windows do. Still air has a very low conductivity. Trapped air also cannot easily circulate and carry energy with it.

Common mistake

Insulation does not stop energy transfer or keep cold in. It only lowers the rate at which energy moves from hot to cold.

Key term

insulator

An insulator is a material with a low thermal conductivity, used to reduce the rate of energy transfer.

Note read

Check your recall[12 marks]

5 written questions. Answer each one in your head or on paper, then open the mark scheme.

  1. 1.Calculate[3 marks]

    Calculate the energy needed to raise the temperature of a 0.50 kg metal block by 40 K. Its specific heat is 400 J/(kg K)400\,\mathrm{J/(kg\,K)}400J/(kgK).

    Show mark schemeHide mark scheme

    Model answer

    Q=mcΔT=(0.50 kg)(400 J/(kg K))(40 K)=8.0×103 JQ=mc\Delta T=(0.50\,\mathrm{kg})(400\,\mathrm{J/(kg\,K)})(40\,\mathrm{K})=8.0\times10^{3}\,\mathrm{J}Q=mcΔT=(0.50kg)(400J/(kgK))(40K)=8.0×103J.

    • 1 mark for writing Q=mcΔTQ=mc\Delta TQ=mcΔT
    • 1 mark for substituting the given values correctly
    • 1 mark for obtaining 8.0×103 J8.0\times10^{3}\,\mathrm{J}8.0×103J with a unit
  2. 2.Explain[2 marks]

    Explain why a material with a large specific heat warms slowly when it gains energy.

    Show mark schemeHide mark scheme

    Model answer

    For a given mass, the temperature change is ΔT=Qmc\Delta T=\frac{Q}{mc}ΔT=mcQ​. A large specific heat gives a small temperature change for the same energy gained.

    • 1 mark for stating that the temperature change equals energy divided by the product of mass and specific heat
    • 1 mark for concluding that a larger specific heat gives a smaller temperature change for the same energy
  3. 3.Determine[2 marks]

    Determine the factor by which the conduction rate through a slab changes when its thickness is doubled and everything else stays the same.

    Show mark schemeHide mark scheme

    Model answer

    The rate is inversely proportional to thickness LLL. Doubling LLL multiplies the rate by 12\frac{1}{2}21​, so the rate halves.

    • 1 mark for stating that the rate is inversely proportional to thickness
    • 1 mark for concluding that the rate becomes one half
  4. 4.Predict[2 marks]

    Predict how the rate of conduction through a wall changes when its area is tripled and the temperature difference across it is doubled.

    Show mark schemeHide mark scheme

    Model answer

    The rate is proportional to both AAA and ΔT\Delta TΔT. The rate is multiplied by 3×2=63\times2=63×2=6.

    • 1 mark for stating that the rate is proportional to area and temperature difference
    • 1 mark for concluding that the rate increases by a factor of 6
  5. 5.Explain[3 marks]

    Explain how a foam cup keeps a drink warm for longer than a metal cup of the same size.

    Show mark schemeHide mark scheme

    Model answer

    Foam has a much lower thermal conductivity than metal, and it traps air, which also conducts poorly. The conduction rate depends on kkk, so energy leaves the drink more slowly through the foam.

    • 1 mark for stating that foam has a lower thermal conductivity
    • 1 mark for linking low conductivity or trapped air to a lower rate of conduction
    • 1 mark for concluding that energy leaves the drink more slowly

Practice this topic

10 quick-fire multiple-choice questions, easy to hard. Tap an answer to see if you're right and the worked explanation. (The written questions with mark schemes are under “Check your recall” above.)

0 right0 of 10 answered

Includes the 2 quick checks in the note above.

3.

Easy·Determine[1 mark]

A sample cools, so ΔT\Delta TΔT is negative in Q=mcΔTQ=mc\Delta TQ=mcΔT. Determine the sign of QQQ.
Show answer and explanation

Answer: A · Worked explanation

The mass and specific heat are positive, and ΔT\Delta TΔT is negative because change is final minus initial. So QQQ is negative, which means the sample loses energy. The reasoning that mass and specific heat are positive ignores the sign of ΔT\Delta TΔT. Energy conservation does not make QQQ zero, because the energy leaves the sample for its surroundings.
4.

Medium·Calculate[2 marks]

A 0.20 kg sample has a specific heat of 500 J/(kg K)500\,\mathrm{J/(kg\,K)}500J/(kgK). Calculate the energy needed to warm it by 30 K.
Show answer and explanation

Answer: B · Worked explanation

Use Q=mcΔT=(0.20 kg)(500 J/(kg K))(30 K)=3.0×103 JQ=mc\Delta T=(0.20\,\mathrm{kg})(500\,\mathrm{J/(kg\,K)})(30\,\mathrm{K})=3.0\times10^{3}\,\mathrm{J}Q=mcΔT=(0.20kg)(500J/(kgK))(30K)=3.0×103J. The value 1.5×104 J1.5\times10^{4}\,\mathrm{J}1.5×104J comes from leaving out the mass, which is the tempting error. The value 3.3 J3.3\,\mathrm{J}3.3J comes from dividing by ΔT\Delta TΔT instead of multiplying. The value 7.5×104 J7.5\times10^{4}\,\mathrm{J}7.5×104J comes from dividing by the mass instead of multiplying it into the product.
5.

Medium·Determine[2 marks]

A 1.5 kg sample has a specific heat of 900 J/(kg K)900\,\mathrm{J/(kg\,K)}900J/(kgK). It gains 27,000 J27{,}000\,\mathrm{J}27,000J. Determine its temperature change.
Show answer and explanation

Answer: D · Worked explanation

Rearrange to ΔT=Qmc=27,000 J(1.5 kg)(900 J/(kg K))=20 K\Delta T=\frac{Q}{mc}=\frac{27{,}000\,\mathrm{J}}{(1.5\,\mathrm{kg})(900\,\mathrm{J/(kg\,K)})}=20\,\mathrm{K}ΔT=mcQ​=(1.5kg)(900J/(kgK))27,000J​=20K. The value 30 K comes from dividing by the specific heat but forgetting the mass. The value 45 K comes from multiplying by the mass instead of dividing by it. The value 0.050 K comes from inverting the fraction.
6.

Medium·Calculate[2 marks]

A wall has area 2.0 m22.0\,\mathrm{m^2}2.0m2, thickness 0.10 m, and thermal conductivity 0.50 W/(m K)0.50\,\mathrm{W/(m\,K)}0.50W/(mK). The temperature difference across it is 20 K. Calculate the rate of energy transfer.
Show answer and explanation

Answer: A · Worked explanation

Use QΔt=kAΔTL=(0.50)(2.0)(20)0.10 W=2.0×102 W\frac{Q}{\Delta t}=\frac{kA\Delta T}{L}=\frac{(0.50)(2.0)(20)}{0.10}\,\mathrm{W}=2.0\times10^{2}\,\mathrm{W}ΔtQ​=LkAΔT​=0.10(0.50)(2.0)(20)​W=2.0×102W. The value 20 W20\,\mathrm{W}20W comes from leaving out the thickness. The value 2.0 W2.0\,\mathrm{W}2.0W comes from multiplying by the thickness instead of dividing by it. The value 2.0×103 W2.0\times10^{3}\,\mathrm{W}2.0×103W comes from an error of a factor of ten in the thickness.
7.

Medium·Predict[1 mark]

Predict which single change would reduce the rate of conduction through a wall.
Show answer and explanation

Answer: C · Worked explanation

The rate is kAΔTL\frac{kA\Delta T}{L}LkAΔT​, so it falls when LLL increases. A thicker wall gives energy a longer path to cross. Increasing AAA, ΔT\Delta TΔT, or kkk each raises the rate, because each sits in the numerator. A larger area is a common slip, since it feels like more material but actually gives energy more room to pass.
8.

Hard·Determine[2 marks]

Two blocks have the same mass. Each gains the same energy. Block X warms by twice as many kelvins as block Y. Determine how the specific heat of X compares with that of Y.
Show answer and explanation

Answer: A · Worked explanation

From ΔT=Qmc\Delta T=\frac{Q}{mc}ΔT=mcQ​, with QQQ and mmm equal, ΔT\Delta TΔT is inversely proportional to ccc. Doubling ΔT\Delta TΔT therefore halves ccc. The claim that X has twice the specific heat assumes a direct proportionality, which is the tempting error. A material that warms more for the same energy resists warming less.
9.

Hard·Calculate[2 marks]

A wall transfers energy at 600 W. The wall is made twice as thick, and the temperature difference across it triples. The area and material are unchanged. Calculate the new rate.
Show answer and explanation

Answer: B · Worked explanation

The rate is proportional to ΔTL\frac{\Delta T}{L}LΔT​. Tripling ΔT\Delta TΔT multiplies it by 3, and doubling LLL multiplies it by 12\frac{1}{2}21​. So the new rate is 600×3×12=900 W600\times3\times\frac{1}{2}=900\,\mathrm{W}600×3×21​=900W. The value 1,800 W ignores the thicker wall. The value 3,600 W wrongly multiplies by the thickness factor.
10.

Hard·Identify[2 marks]

Two cups have walls of equal area and thickness. One is foam and one is metal. Each holds the same mass of coffee at 80 °C in a 20 °C room. The foam cup stays warmer. Identify the best explanation.
Show answer and explanation

Answer: D · Worked explanation

With equal area, thickness, and temperature difference, the conduction rate depends on kkk. Foam has a lower kkk, so energy leaves more slowly. Cold does not flow into the cup; energy flows out, from hot to cold. A larger specific heat would change how much the temperature falls per joule lost, not stop energy loss, and foam supplies no energy at all.

Keep going

Next topic9.6 Entropy and the second lawPrevious topic9.4 First law of thermodynamics

More in Unit 9 · Thermodynamics

  1. 9.1Kinetic theory of temperature and pressureNotes · 10 questions
  2. 9.2The ideal gas lawNotes · 10 questions
  3. 9.3Thermal energy transfer and equilibriumNotes · 10 questions
  4. 9.4First law of thermodynamicsNotes · 10 questions
  5. 9.5Specific heat and thermal conductivityNotes · 10 questions
  6. 9.6Entropy and the second lawNotes · 10 questions

All AP Physics 2 topics →

Draft: written by Scribe and checked automatically, not yet by a subject reviewer.

Practice questions are original, written by Scribe and checked automatically for correctness.

Topic codes follow the official numbering. Not endorsed by College Board or any exam board.

On this page

0/5 read

  1. 1Different materials need different energy for the same warming
  2. 2Energy transferred equals mass times specific heat times temperature change
  3. 3Conduction moves energy through a material from hot to cold
  4. 4Conduction rate grows with area and temperature difference
  5. 5Good insulation uses low conductivity and added thickness
  6. Check your recall
  7. Practice: 10 questions
All coursesScribeHow it worksPricingPrivacyTerms

Notes and questions are written by Scribe in our own words. Topic codes follow the official course numbering so you can find your place. Not produced or endorsed by the IB, College Board, AQA, OCR, Pearson Edexcel or any exam board.

© 2026 Scribe