Scribe logoScribeNotes & practice
Sign inStart free
  1. Notes
  2. ›AQA A-level Physics
  3. ›3.1 Measurements and their errors
  4. ›3.1.2 Limits of measurement

AQA A-level Physics · Section 3.1 · Measurements and their errors

3.1.2 Limits of measurement

Explain the difference between accuracy and precision, identify sources of uncertainty, and calculate percentage uncertainties.

  • 5 min read
  • 6 parts
  • 10 questions
  • Draft
Start a Quick 5 on this topic→Jump to the 10 questions
1/6Every measurement has an uncertainty around it
  1. 1Every measurement has an uncertainty around it
  2. 2Accuracy and precision describe two different qualities
  3. 3Random and systematic errors push results in different ways
  4. 4Resolution and the spread of repeats set the absolute uncertainty
  5. 5Percentage uncertainty compares the uncertainty with the reading
  6. 6Percentage uncertainties add when quantities are multiplied or divided
  7. Check your recall
  8. Practice: 10 questions
1

Part 1 of 6: Every measurement has an uncertainty around it

Measure the length of a desk twice and you will rarely get identical numbers. The ruler, your eye and the desk edge all limit the result. No measurement gives the true value exactly.

We therefore quote a result with an uncertainty, such as (12.3±0.2) cm(12.3\pm0.2)\,\mathrm{cm}(12.3±0.2)cm. This means the true value probably lies between 12.1 cm and 12.5 cm. A smaller uncertainty means a better measurement.

Uncertainty is not the same as a mistake. A mistake, such as misreading a scale, can be corrected. An uncertainty is built into every measurement.

Key terms · tap one for its definition

true value

The true value of a quantity is the value that a perfect measurement, free from every limitation, would give.

uncertainty

An uncertainty is the range of values, written after a ± sign, within which the true value of a measurement is expected to lie.

Part 1 done

2

Part 2 of 6: Accuracy and precision describe two different qualities

Picture darts thrown at a board. One thrower’s darts land close together. Another thrower’s darts are centred on the bullseye.

Measurements behave in the same way. Readings that agree closely with each other show high precision. Readings that lie close to the true value show high accuracy.

Figure 1. Tight grouping shows precision. Grouping centred on the bullseye shows accuracy.

A set of readings can be precise but not accurate. It can also be accurate on average but widely scattered. High precision shows a small spread, but it says nothing about distance from the true value. Each quality must be judged separately.

Key terms · tap one for its definition

precision

Precision is the closeness of agreement between repeated measurements, shown by a small spread of readings.

accuracy

Accuracy is the closeness of a measurement, or of the mean of several, to the true value.

Part 2 done

Quick check

One question on the part you just read

Easy

Identify the term for how closely repeated readings agree with one another.
Show answer and explanation

Answer: D · Worked explanation

Precision describes how closely repeated readings agree with each other, shown by a small spread. Accuracy is different, because it describes how close a reading is to the true value. A set of readings can be tightly grouped and still be far from that value, so the two terms must not be swapped.
3

Part 3 of 6: Random and systematic errors push results in different ways

Timing a falling ball by hand shows both kinds of error at once. Your reaction time varies from trial to trial. A stopwatch that always starts late adds the same delay every time.

A random error changes a reading unpredictably, sometimes high and sometimes low. It causes scatter and so lowers precision. Averaging repeat readings reduces its effect.

A systematic error shifts every reading by the same amount in the same direction. It lowers accuracy. A zero error, where an instrument reads a non-zero value when it should read zero, is a common example.

Comparing random and systematic errors

FeatureRandom errorSystematic error
Pattern in readingsScatter above and below the true valueSame shift every time
Effect of averagingReduces the effectDoes not remove it
ExampleVarying reaction timeZero error
Feature
Pattern in readings
Random error
Scatter above and below the true value
Systematic error
Same shift every time
Feature
Effect of averaging
Random error
Reduces the effect
Systematic error
Does not remove it
Feature
Example
Random error
Varying reaction time
Systematic error
Zero error

Common mistake

Repeating readings does not remove a systematic error. Check the instrument against a known value, or correct for the zero error.

Key terms · tap one for its definition

random error

A random error is an unpredictable variation in readings that scatters them about the mean and is reduced by averaging.

systematic error

A systematic error is an error that shifts every reading by a consistent amount in one direction, so averaging cannot remove it.

zero error

A zero error is a systematic error in which an instrument gives a non-zero reading when the true value is zero.

Part 3 done

4

Part 4 of 6: Resolution and the spread of repeats set the absolute uncertainty

Now we need a number to put after the ± sign. The smallest change an instrument can show is its resolution. A ruler marked in millimetres has a resolution of 1 mm. For a single reading, a common estimate of the uncertainty is half the smallest division, here 0.5 mm.

With repeat readings, use their spread. Half the difference between the largest and smallest reading gives a good estimate. An uncertainty in the unit of the quantity, such as 0.5 mm, is an absolute uncertainty. If both estimates are available, use the larger one.

Key terms · tap one for its definition

resolution

The resolution of an instrument is the smallest change in a quantity that the instrument can detect or display.

absolute uncertainty

An absolute uncertainty is an uncertainty expressed in the same unit as the measured quantity, for example ±0.5 mm\pm0.5\,\mathrm{mm}±0.5mm.

Part 4 done

Quick check

One question on the part you just read

Easy

Identify which of these is an example of a systematic error.
Show answer and explanation

Answer: A · Worked explanation

A balance that reads a fixed non-zero value with nothing on it has a zero error, which shifts every reading by the same amount. The remaining cases vary unpredictably from one reading to the next, so they are random errors. Averaging would reduce those, but it would not remove the zero error.
5

Part 5 of 6: Percentage uncertainty compares the uncertainty with the reading

A ±1 mm uncertainty matters little on a 2 m rope but a lot on a 5 mm bolt. The same absolute uncertainty is a very different fraction of each. The percentage uncertainty expresses that fraction. Percentages also let you compare measurements of very different sizes.

Divide the absolute uncertainty by the measured value and multiply by 100%, so that percentage uncertainty=absolute uncertaintymeasured value×100%\mathrm{percentage~uncertainty}=\frac{\mathrm{absolute~uncertainty}}{\mathrm{measured~value}}\times100\%percentage uncertainty=measured valueabsolute uncertainty​×100%. The result has no unit. A smaller percentage means a more reliable result.

Exam tip

Quote an absolute uncertainty to one significant figure. Match its decimal places to the reading, as in (2.32±0.03) s(2.32\pm0.03)\,\mathrm{s}(2.32±0.03)s.

Worked example

Finding a percentage uncertainty

A student times a trolley four times and records 2.31 s, 2.35 s, 2.29 s and 2.33 s. Calculate the mean time and its percentage uncertainty.
  1. 1
    Find the mean: 2.31+2.35+2.29+2.334 s=9.284 s=2.32 s\frac{2.31+2.35+2.29+2.33}{4}\,\mathrm{s}=\frac{9.28}{4}\,\mathrm{s}=2.32\,\mathrm{s}42.31+2.35+2.29+2.33​s=49.28​s=2.32s.
  2. 2
    Find the absolute uncertainty from half the difference between the largest and smallest readings: 2.35−2.292 s=0.03 s\frac{2.35-2.29}{2}\,\mathrm{s}=0.03\,\mathrm{s}22.35−2.29​s=0.03s.
  3. 3
    Use percentage uncertainty=absolute uncertaintymean×100%\mathrm{percentage~uncertainty}=\frac{\mathrm{absolute~uncertainty}}{\mathrm{mean}}\times100\%percentage uncertainty=meanabsolute uncertainty​×100%.
  4. 4
    Substitute: 0.03 s2.32 s×100%≈1.3%\frac{0.03\,\mathrm{s}}{2.32\,\mathrm{s}}\times100\%\approx1.3\%2.32s0.03s​×100%≈1.3%.

Answer: The time is (2.32±0.03) s(2.32\pm0.03)\,\mathrm{s}(2.32±0.03)s, with a percentage uncertainty of ≈1.3%\approx1.3\%≈1.3%.

Key term

percentage uncertainty

The percentage uncertainty is the absolute uncertainty divided by the measured value, multiplied by 100%, and has no unit.

Part 5 done

6

Part 6 of 6: Percentage uncertainties add when quantities are multiplied or divided

Most results come from combining measurements, such as speed from distance and time. The uncertainties then combine as well. Work out each percentage uncertainty first, then combine them. Three rules cover the cases you need.

  • Adding or subtracting quantities: add the absolute uncertainties.
  • Multiplying or dividing quantities: add the percentage uncertainties.
  • Raising a quantity to a power: multiply its percentage uncertainty by the power.

Uncertainties never cancel, even when quantities are divided or subtracted. A length with a 2% uncertainty has a squared value with a 4% uncertainty.

Worked example

Uncertainty in an area

A rectangle has length (40.0±0.4) cm(40.0\pm0.4)\,\mathrm{cm}(40.0±0.4)cm and width (25.0±0.5) cm(25.0\pm0.5)\,\mathrm{cm}(25.0±0.5)cm. Calculate its area and the absolute uncertainty in the area.
  1. 1
    Find each percentage uncertainty: 0.440.0×100%=1.0%\frac{0.4}{40.0}\times100\%=1.0\%40.00.4​×100%=1.0% and 0.525.0×100%=2.0%\frac{0.5}{25.0}\times100\%=2.0\%25.00.5​×100%=2.0%.
  2. 2
    Add them for a product: 1.0%+2.0%=3.0%1.0\%+2.0\%=3.0\%1.0%+2.0%=3.0%.
  3. 3
    Find the area: 40.0 cm×25.0 cm=1000 cm240.0\,\mathrm{cm}\times25.0\,\mathrm{cm}=1000\,\mathrm{cm^{2}}40.0cm×25.0cm=1000cm2.
  4. 4
    Find the absolute uncertainty: 3.0%×1000 cm2=30 cm23.0\%\times1000\,\mathrm{cm^{2}}=30\,\mathrm{cm^{2}}3.0%×1000cm2=30cm2.

Answer: The area is (1.00±0.03)×103 cm2(1.00\pm0.03)\times10^{3}\,\mathrm{cm^{2}}(1.00±0.03)×103cm2.

Go deeperUncertainty in the gradient of a graph

Plot each point with an error bar, a short line showing the uncertainty in that reading. Draw a best-fit line through the points. Then draw a worst acceptable line, which is steeper or shallower but still passes through every error bar.

The difference between the two gradients is the uncertainty in the gradient. The same method gives the uncertainty in an intercept.

Note read

Check your recall[15 marks]

6 written questions. Answer each one in your head or on paper, then open the mark scheme.

  1. 1.Explain[2 marks]

    Explain the difference between accuracy and precision.

    Show mark schemeHide mark scheme

    Model answer

    Accuracy is how close a reading is to the true value. Precision is how closely repeated readings agree with each other.

    • 1 mark for stating that accuracy is closeness to the true value
    • 1 mark for stating that precision is closeness of agreement between repeated readings
  2. 2.Compare[3 marks]

    Compare random errors and systematic errors, including how each can be reduced.

    Show mark schemeHide mark scheme

    Model answer

    Random errors scatter readings above and below the true value, and averaging repeat readings reduces them. Systematic errors shift all readings by the same amount in one direction. Averaging does not remove them, so the instrument must be checked or the zero error corrected.

    • 1 mark for stating that random errors cause scatter above and below the true value
    • 1 mark for stating that systematic errors shift all readings in the same direction by the same amount
    • 1 mark for stating that averaging reduces random errors but not systematic errors, which need a check or correction
  3. 3.Suggest[2 marks]

    Suggest how a student could check for a zero error on a digital balance.

    Show mark schemeHide mark scheme

    Model answer

    Read the display with nothing on the balance. Any non-zero reading is a zero error and should be subtracted from later readings.

    • 1 mark for reading the balance with nothing on it
    • 1 mark for stating that a non-zero reading is a zero error to correct for in all readings
  4. 4.Calculate[2 marks]

    Calculate the percentage uncertainty in a voltage of 6.0 V that has an absolute uncertainty of 0.3 V.

    Show mark schemeHide mark scheme

    Model answer

    0.3 V6.0 V×100%=5%\frac{0.3\,\mathrm{V}}{6.0\,\mathrm{V}}\times100\%=5\%6.0V0.3V​×100%=5%.

    • 1 mark for dividing the absolute uncertainty by the measured value and multiplying by 100%
    • 1 mark for obtaining 5% (accept 5.0%)
  5. 5.Calculate[3 marks]

    Calculate the percentage uncertainty in the volume of a cube of side (5.0±0.1) cm(5.0\pm0.1)\,\mathrm{cm}(5.0±0.1)cm, given that its volume depends on the side cubed.

    Show mark schemeHide mark scheme

    Model answer

    The side has a percentage uncertainty of 0.15.0×100%=2.0%\frac{0.1}{5.0}\times100\%=2.0\%5.00.1​×100%=2.0%. The volume depends on the side cubed, so the percentage uncertainty is 3×2.0%=6.0%3\times2.0\%=6.0\%3×2.0%=6.0%.

    • 1 mark for calculating 2.0% for the side
    • 1 mark for multiplying by the power 3
    • 1 mark for obtaining 6.0%
  6. 6.Calculate[3 marks]

    Repeat readings of a current are 0.52 A, 0.48 A, 0.50 A and 0.54 A. Calculate the mean and the absolute uncertainty, using half the difference between the largest and smallest readings.

    Show mark schemeHide mark scheme

    Model answer

    The mean is 0.52+0.48+0.50+0.544 A=0.51 A\frac{0.52+0.48+0.50+0.54}{4}\,\mathrm{A}=0.51\,\mathrm{A}40.52+0.48+0.50+0.54​A=0.51A. The uncertainty is 0.54−0.482 A=0.03 A\frac{0.54-0.48}{2}\,\mathrm{A}=0.03\,\mathrm{A}20.54−0.48​A=0.03A.

    • 1 mark for calculating the mean as 0.51 A
    • 1 mark for finding half the difference between 0.54 A and 0.48 A
    • 1 mark for obtaining an absolute uncertainty of 0.03 A

Practice this topic

10 quick-fire multiple-choice questions, easy to hard. Tap an answer to see if you're right and the worked explanation. (The written questions with mark schemes are under “Check your recall” above.)

0 right0 of 10 answered

Includes the 2 quick checks in the note above.

3.

Easy·Identify[1 mark]

Identify what is meant by the resolution of a measuring instrument.
Show answer and explanation

Answer: C · Worked explanation

Resolution is the smallest change in a quantity that an instrument can detect, such as 1 mm on a ruler marked in millimetres. Closeness to the true value is accuracy, and agreement between repeated readings is precision. The difference between the largest and smallest readings is a range, which can be used to estimate an uncertainty.
4.

Medium·Calculate[2 marks]

Calculate the percentage uncertainty in a length of 80.0 cm that has an absolute uncertainty of 0.4 cm.
Show answer and explanation

Answer: B · Worked explanation

Percentage uncertainty is the absolute uncertainty divided by the measured value, multiplied by 100%. So 0.4 cm80.0 cm×100%=0.5%\frac{0.4\,\mathrm{cm}}{80.0\,\mathrm{cm}}\times100\%=0.5\%80.0cm0.4cm​×100%=0.5%. The value 0.005% forgets to multiply by 100%. The value 200% turns the fraction upside down, dividing the length by the uncertainty. Quote the answer to the precision of the data, so 0.5% is enough here.
5.

Medium·Determine[2 marks]

Three times are recorded as 3.42 s, 3.56 s and 3.48 s. Determine the absolute uncertainty in the mean, using half the difference between the largest and smallest readings.
Show answer and explanation

Answer: D · Worked explanation

The largest reading is 3.56 s and the smallest is 3.42 s, a difference of 0.14 s. Half of this is 0.07 s. The value 0.14 s forgets to halve. The value 3.49 s is the mean of the three readings, which is the measured value rather than an uncertainty.
6.

Medium·Determine[2 marks]

A speed is found from a distance of (2.00±0.02) m(2.00\pm0.02)\,\mathrm{m}(2.00±0.02)m and a time of (0.50±0.01) s(0.50\pm0.01)\,\mathrm{s}(0.50±0.01)s. Determine the percentage uncertainty in the speed.
Show answer and explanation

Answer: C · Worked explanation

Speed is distance divided by time, so the percentage uncertainties add. The distance gives 0.022.00×100%=1.0%\frac{0.02}{2.00}\times100\%=1.0\%2.000.02​×100%=1.0% and the time gives 0.010.50×100%=2.0%\frac{0.01}{0.50}\times100\%=2.0\%0.500.01​×100%=2.0%, a total of 3.0%. The value 1.0% subtracts, wrongly treating division as cancelling uncertainty. The value 1.5% averages the two instead of adding them.
7.

Medium·Identify[1 mark]

A standard mass is known to be 20.0 g. It is measured five times, giving 22.1 g, 22.2 g, 22.1 g, 22.2 g and 22.1 g. Identify the best description of these readings.
Show answer and explanation

Answer: A · Worked explanation

The readings differ by only 0.1 g, so they are precise. Their mean is about 22.1 g, which is 2.1 g from the true value, so they are not accurate. A constant offset like this suggests a systematic error such as a zero error. The readings are not widely scattered, so they cannot be described as imprecise.
8.

Hard·Determine[2 marks]

A circle has radius (4.0±0.2) cm(4.0\pm0.2)\,\mathrm{cm}(4.0±0.2)cm. The area is πr2\pi r^{2}πr2, where rrr is the radius. Determine the percentage uncertainty in the area.
Show answer and explanation

Answer: B · Worked explanation

The radius has a percentage uncertainty of 0.24.0×100%=5.0%\frac{0.2}{4.0}\times100\%=5.0\%4.00.2​×100%=5.0%. The area depends on r2r^{2}r2, so the percentage uncertainty is multiplied by the power 2, giving 10%. The constant π\piπ has no uncertainty. The value 5.0% ignores the square, while 25% squares the percentage itself.
9.

Hard·Identify[2 marks]

A student measures a wire’s diameter ten times with a micrometer that has an unnoticed zero error of +0.02 mm. The true diameter is 0.50 mm and the readings are all close to 0.52 mm. Identify the correct statement.
Show answer and explanation

Answer: D · Worked explanation

A zero error shifts every reading by the same amount, so it is a systematic error. The readings agree closely, so they are precise, but their mean stays about 0.02 mm too high. Averaging only reduces random scatter. Calling the readings imprecise confuses distance from the true value, which is accuracy, with spread.
10.

Hard·Determine[2 marks]

A density is found from a mass of (150±3) g(150\pm3)\,\mathrm{g}(150±3)g and a volume of (60±3) cm3(60\pm3)\,\mathrm{cm^{3}}(60±3)cm3. Determine the percentage uncertainty in the density.
Show answer and explanation

Answer: A · Worked explanation

Density is mass divided by volume, so add the percentage uncertainties. The mass gives 3150×100%=2.0%\frac{3}{150}\times100\%=2.0\%1503​×100%=2.0% and the volume gives 360×100%=5.0%\frac{3}{60}\times100\%=5.0\%603​×100%=5.0%, a total of 7.0%. The value 3.0% subtracts the two. The value 6.0% adds the absolute uncertainties 3 and 3, which have different units and cannot be added.

Keep going

Next topic3.1.3 Estimating physical quantitiesPrevious topic3.1.1 SI units and prefixes

More in Section 3.1 · Measurements and their errors

  1. 3.1.1SI units and prefixesNotes · 10 questions
  2. 3.1.2Limits of measurementNotes · 10 questions
  3. 3.1.3Estimating physical quantitiesNotes · 10 questions

All AQA A-level Physics topics →

Draft: written by Scribe and checked automatically, not yet by a subject reviewer.

Practice questions are original, written by Scribe and checked automatically for correctness.

Topic codes follow the official numbering. Not endorsed by AQA or any exam board.

On this page

0/6 read

  1. 1Every measurement has an uncertainty around it
  2. 2Accuracy and precision describe two different qualities
  3. 3Random and systematic errors push results in different ways
  4. 4Resolution and the spread of repeats set the absolute uncertainty
  5. 5Percentage uncertainty compares the uncertainty with the reading
  6. 6Percentage uncertainties add when quantities are multiplied or divided
  7. Check your recall
  8. Practice: 10 questions
All coursesScribeHow it worksPricingPrivacyTerms

Notes and questions are written by Scribe in our own words. Topic codes follow the official course numbering so you can find your place. Not produced or endorsed by the IB, College Board, AQA, OCR, Pearson Edexcel or any exam board.

© 2026 Scribe