Scribe logoScribeNotes & practice
Sign inStart free
  1. Notes
  2. ›AP Environmental Science
  3. ›5 Land and Water Use
  4. ›5.5 Irrigation methods

AP Environmental Science · Unit 5 · Land and Water Use

5.5 Irrigation methods

Compare major irrigation systems, explain how irrigation affects water resources, and identify ways to irrigate more efficiently.

  • 4 min read
  • 5 parts
  • 10 questions
  • Draft
Start a Quick 5 on this topic→Jump to the 10 questions
1/5Irrigation supplies water that rain does not provide
  1. 1Irrigation supplies water that rain does not provide
  2. 2Flood and furrow systems are simple but wasteful
  3. 3Spray and drip systems deliver water more precisely
  4. 4Irrigation can deplete and degrade water resources
  5. 5Better methods and timing can reduce water waste
  6. Check your recall
  7. Practice: 10 questions
1

Part 1 of 5: Irrigation supplies water that rain does not provide

A farm in a dry region cannot rely on rain alone. Farmers there move water from rivers, lakes, or groundwater onto their fields. This practice is irrigation, and it lets crops grow where rainfall is too low or too uneven.

Irrigation is a large use of fresh water, so the method matters. Some water reaches the roots, but some evaporates, runs off, or drains below them. The share that crops actually use is the irrigation efficiency.

The next sections compare the main systems and rank them by how much water they waste.

Key terms · tap one for its definition

irrigation

Irrigation is the artificial application of water to land to support crop growth where natural rainfall is not enough.

irrigation efficiency

Irrigation efficiency is the percentage of applied water that crops take up rather than lose to evaporation, runoff, or deep drainage.

Part 1 done

2

Part 2 of 5: Flood and furrow systems are simple but wasteful

Start with the oldest approach, which needs almost no equipment. In flood irrigation, water covers the whole field and soaks in. In furrow irrigation, water runs down small channels between crop rows.

Both systems rely on gravity, so pumps and pressure are not needed. They are cheap to set up and run. The drawback is waste. Water stays on the surface for a long time, so much of it evaporates or drains past the roots.

Uneven land makes this worse. Low spots collect too much water while high spots stay dry.

Key terms · tap one for its definition

flood irrigation

Flood irrigation is a method that covers an entire field with a layer of water that soaks into the soil.

furrow irrigation

Furrow irrigation is a method that sends water by gravity along small channels dug between rows of crops.

Part 2 done

Quick check

One question on the part you just read

Easy

Identify the irrigation method that releases water slowly through small holes in tubes placed at the plant roots.
Show answer and explanation

Answer: C · Worked explanation

Drip irrigation sends water through tubes with tiny holes directly to the root zone, so little water evaporates or runs off. Spray irrigation also uses pipes, but it throws water into the air, where wind and heat remove some of it.
3

Part 3 of 5: Spray and drip systems deliver water more precisely

Pipes and pumps allow water to be targeted. Spray irrigation pushes water through pipes to sprinklers, which spray it over the crops like rain. Pumping needs energy, and wind and heat carry some of the spray away.

Drip irrigation goes a step further. Narrow tubes with tiny holes release water slowly right at each plant’s roots. Very little evaporates, and almost none runs off. Because only the root zone gets wet, weeds between rows receive less water too. This precision makes drip the most water-efficient choice.

Comparison of four irrigation methods

MethodWater efficiencySetup costMain drawback
FloodLowLowLarge evaporation and drainage losses
FurrowLowLowRunoff at row ends and drainage losses
SprayModerateMediumEnergy use and wind drift
DripHighestHighClogged holes and installation cost
Method
Flood
Water efficiency
Low
Setup cost
Low
Main drawback
Large evaporation and drainage losses
Method
Furrow
Water efficiency
Low
Setup cost
Low
Main drawback
Runoff at row ends and drainage losses
Method
Spray
Water efficiency
Moderate
Setup cost
Medium
Main drawback
Energy use and wind drift
Method
Drip
Water efficiency
Highest
Setup cost
High
Main drawback
Clogged holes and installation cost

Key terms · tap one for its definition

spray irrigation

Spray irrigation is a method that delivers pressurized water through pipes to sprinklers that spray it over crops.

drip irrigation

Drip irrigation is a method that releases water slowly from tubes with small holes directly onto the soil at plant roots.

Part 3 done

4

Part 4 of 5: Irrigation can deplete and degrade water resources

Even efficient irrigation takes water from somewhere. Tapped rivers carry less water downstream, which harms wetlands and the species that live there. Many farms also pump from an aquifer, an underground layer that holds groundwater. If pumping is faster than natural refilling, the water table, the top of the groundwater, drops and wells run dry.

  • Salinization: irrigation water carries dissolved salts, and evaporation leaves them in the soil.
  • Waterlogging: too much water fills the air spaces in soil, so roots lack oxygen.
  • Runoff: water leaving fields carries fertilizer, pesticides, and sediment into streams.

Common mistake

Salt buildup does not come only from seawater. Ordinary irrigation water holds small amounts of salt that concentrate as the water evaporates.

Key terms · tap one for its definition

aquifer

An aquifer is an underground layer of rock or sediment that holds groundwater and can supply wells.

salinization

Salinization is the buildup of salts in soil, often when irrigation water evaporates and leaves dissolved salts behind.

waterlogging

Waterlogging is the saturation of soil with water so that air spaces fill and plant roots receive too little oxygen.

Part 4 done

Quick check

One question on the part you just read

Easy

Which statement describes a main disadvantage of flood irrigation?
Show answer and explanation

Answer: A · Worked explanation

Flood irrigation lets water stand over the whole field, so evaporation and deep drainage waste a large share. It relies on gravity, so heavy energy use is not its main problem. Clogging belongs to drip systems, which use narrow tubes with tiny holes.
5

Part 5 of 5: Better methods and timing can reduce water waste

Farmers can cut these harms without giving up irrigation. The most direct step is switching from flood or furrow to drip or well-designed sprinklers. Other steps add to the savings.

  • Water early in the morning or at night to reduce evaporation.
  • Use a soil moisture sensor to apply water only when plants need it.
  • Line canals and fix leaks to stop seepage.
  • Mulch the soil surface to slow evaporation.
  • Grow crops that suit the local climate.

Exam tip

When you recommend a change, name the loss it reduces. Drip tubing, for example, cuts evaporation and runoff.

Go deeperEfficiency gains do not always save water

Cheaper, more efficient irrigation can tempt farmers to irrigate more land or grow thirstier crops. Total water use may then stay the same or even rise. Savings are most reliable when rules also limit how much water can be withdrawn.

Suppose drip tubing cuts water use per field by 40 percent, but the irrigated area grows by 80 percent. Total use becomes 0.60 × 1.80 = 1.08 of the original, an 8 percent rise.

Key term

soil moisture sensor

A soil moisture sensor is a device that measures the water content of soil so irrigation can be timed to crop need.

Note read

Check your recall[13 marks]

6 written questions. Answer each one in your head or on paper, then open the mark scheme.

  1. 1.Identify[1 mark]

    Identify the irrigation method that uses gravity to send water along channels between crop rows.

    Show mark schemeHide mark scheme

    Model answer

    Furrow irrigation.

    • 1 mark for naming furrow irrigation
  2. 2.Compare[3 marks]

    Compare drip irrigation with flood irrigation in water efficiency and cost.

    Show mark schemeHide mark scheme

    Model answer

    Drip irrigation is far more efficient because water goes straight to the roots with little evaporation or runoff. Flood irrigation loses much water to evaporation and drainage. Drip systems cost more to install, while flood systems are cheap.

    • 1 mark for stating that drip irrigation has higher water efficiency
    • 1 mark for explaining that flood irrigation loses more water to evaporation or drainage
    • 1 mark for stating that drip costs more to set up and flood costs less
  3. 3.Describe[2 marks]

    Describe how irrigation can lead to salinization of soil.

    Show mark schemeHide mark scheme

    Model answer

    Irrigation water contains dissolved salts. When the water evaporates, the salts stay behind and build up in the soil, which reduces crop growth.

    • 1 mark for stating that irrigation water contains dissolved salts
    • 1 mark for stating that evaporation leaves the salts in the soil, where they build up
  4. 4.Explain[2 marks]

    Explain why pumping groundwater for irrigation faster than natural refilling is a problem.

    Show mark schemeHide mark scheme

    Model answer

    The water table drops as more water is removed than is replaced. Wells may then run dry, so farms lose their water supply.

    • 1 mark for stating that withdrawal exceeds natural refilling so the water table falls
    • 1 mark for explaining that wells may run dry or the supply is lost
  5. 5.Identify[2 marks]

    Identify two changes that would reduce water lost to evaporation on an irrigated farm.

    Show mark schemeHide mark scheme

    Model answer

    Irrigate early in the morning or at night, and switch to drip irrigation. Mulching the soil would also work.

    • 1 mark for identifying one valid change, such as timing irrigation for cooler hours
    • 1 mark for identifying a second valid change, such as drip irrigation or mulching
  6. 6.Justify[3 marks]

    Justify the choice of drip irrigation for an orchard in a dry region, even though it costs more to install.

    Show mark schemeHide mark scheme

    Model answer

    Drip irrigation delivers water to the roots, so little is lost to evaporation or runoff. Saving scarce water lowers pumping and water costs over time. This also protects groundwater or river supplies, which offsets the higher installation cost.

    • 1 mark for stating that drip irrigation wastes little water through evaporation or runoff
    • 1 mark for linking the savings to scarce water or lower long-term costs
    • 1 mark for recognizing that the benefits outweigh the higher installation cost

Practice this topic

10 quick-fire multiple-choice questions, easy to hard. Tap an answer to see if you're right and the worked explanation. (The written questions with mark schemes are under “Check your recall” above.)

0 right0 of 10 answered

Includes the 2 quick checks in the note above.

3.

Easy[1 mark]

Which problem occurs when salts left behind by evaporating irrigation water build up in soil?
Show answer and explanation

Answer: D · Worked explanation

Evaporation removes water but leaves dissolved salts in the soil, and this buildup is salinization. Waterlogging is different: it is a shortage of oxygen in saturated soil, not a buildup of salt. Aquifer depletion concerns groundwater levels, not soil chemistry.
4.

Medium·Calculate[2 marks]

Calculate the irrigation efficiency of a field that receives 10,000 L of water when its crops take up 6,000 L.
Show answer and explanation

Answer: B · Worked explanation

Irrigation efficiency is water used by crops divided by water applied, times 100. Here 6,000 L10,000 L×100=60%\frac{6{,}000\,\mathrm{L}}{10{,}000\,\mathrm{L}}\times100=60\%10,000L6,000L​×100=60%. The value 40% is the share that was lost, not the share that crops used. The value 167% comes from dividing in the wrong order.
5.

Medium[2 marks]

An orchard grower in a hot, windy region wants to cut evaporation losses. Which change is most likely to help?
Show answer and explanation

Answer: D · Worked explanation

Drip tubing puts water at the roots and exposes little water to heat and wind. Running sprinklers at midday increases evaporation because the air is hottest then. Flood irrigation keeps even more water standing on the surface, so it would not reduce losses.
6.

Medium·Explain[2 marks]

Explain why pumping water from an aquifer faster than natural refilling can harm farms.
Show answer and explanation

Answer: B · Worked explanation

If more water is removed than is replaced, the water table drops. Wells then need to be deeper or may run dry. Oxygen shortage in roots is waterlogging, which comes from too much water applied, not from too little groundwater.
7.

Medium[2 marks]

A farmer installs soil moisture sensors. What is the most direct benefit?
Show answer and explanation

Answer: C · Worked explanation

Sensors measure the water content of soil, so irrigation can be timed to what crops need and less is wasted. Slowing surface evaporation is what mulch does, and sensors do not stop wind drift or remove salts.
8.

Hard[2 marks]

A field in a dry climate has been flood-irrigated for many years. Crop yields have fallen, and a white crust now covers the soil surface. Which cause is most likely?
Show answer and explanation

Answer: A · Worked explanation

A white crust in a dry climate points to salts left by repeated evaporation, which is salinization. Waterlogging would show soggy soil rather than a crust, and a dropping water table affects wells, not surface salt. Spray drift belongs to sprinkler systems, not flood irrigation.
9.

Hard·Determine[2 marks]

Switching to drip irrigation cuts water use per hectare by 40%. The farmer then expands the irrigated area by 80%. Determine the change in total water use.
Show answer and explanation

Answer: C · Worked explanation

Total use = 0.60 × 1.80 = 1.08 of the original, so use rises 8%. An increase of 40% comes from adding 80% and subtracting 40%, but the changes multiply rather than add. A decrease of 40% ignores the larger area.
10.

Hard[2 marks]

Which pair of changes would both reduce evaporation losses?
Show answer and explanation

Answer: B · Worked explanation

Night watering avoids the hottest, driest hours and drip tubing exposes little water to the air, so both cut evaporation. Mulching helps, but raising the sprinklers increases wind drift. Lining canals stops seepage, yet flood irrigation increases evaporation.

Keep going

Next topic5.6 Pest control methodsPrevious topic5.4 Impacts of agricultural practices

More in Unit 5 · Land and Water Use

  1. 5.1Tragedy of the commonsNotes · 10 questions
  2. 5.2ClearcuttingNotes · 10 questions
  3. 5.3The Green RevolutionNotes · 10 questions
  4. 5.4Impacts of agricultural practicesNotes · 10 questions
  5. 5.5Irrigation methodsNotes · 10 questions
  6. 5.6Pest control methodsNotes · 10 questions
  7. 5.7Meat production methodsNotes · 10 questions
  8. 5.8OverfishingNotes · 10 questions
  9. 5.9MiningNotes · 10 questions

All AP Environmental Science topics →

Draft: written by Scribe and checked automatically, not yet by a subject reviewer.

Practice questions are original, written by Scribe and checked automatically for correctness.

Topic codes follow the official numbering. Not endorsed by College Board or any exam board.

On this page

0/5 read

  1. 1Irrigation supplies water that rain does not provide
  2. 2Flood and furrow systems are simple but wasteful
  3. 3Spray and drip systems deliver water more precisely
  4. 4Irrigation can deplete and degrade water resources
  5. 5Better methods and timing can reduce water waste
  6. Check your recall
  7. Practice: 10 questions
All coursesScribeHow it worksPricingPrivacyTerms

Notes and questions are written by Scribe in our own words. Topic codes follow the official course numbering so you can find your place. Not produced or endorsed by the IB, College Board, AQA, OCR, Pearson Edexcel or any exam board.

© 2026 Scribe