Scribe logoScribeNotes & practice
Sign inStart free
  1. Notes
  2. ›AP Environmental Science
  3. ›5 Land and Water Use
  4. ›5.9 Mining

AP Environmental Science · Unit 5 · Land and Water Use

5.9 Mining

Describe common mining methods, explain their environmental impacts, and identify ways to reduce the harm mining causes.

  • 4 min read
  • 5 parts
  • 10 questions
  • Draft
Start a Quick 5 on this topic→Jump to the 10 questions
1/5Mining removes valuable materials from the ground
  1. 1Mining removes valuable materials from the ground
  2. 2Surface mining strips away land to expose shallow ore
  3. 3Subsurface mining reaches deep ore through tunnels
  4. 4Mining damages land, water, and air
  5. 5Planning, cleanup, and recycling reduce mining damage
  6. Check your recall
  7. Practice: 10 questions
1

Part 1 of 5: Mining removes valuable materials from the ground

Phones, cars, and buildings all depend on materials taken from the earth. Mining is the process that removes them. An ore is a rock that holds enough of a valuable metal or mineral to be worth extracting.

Before miners can reach an ore, they must deal with whatever lies above it. The soil and rock that cover a deposit are called overburden. How much overburden there is, and how deep the ore sits, decides which mining method makes sense.

Mining supplies metals such as iron, copper, and aluminum. It also supplies coal, sand, gravel, and stone.

Key terms · tap one for its definition

ore

An ore is a naturally occurring rock that contains a metal or mineral in a concentration high enough to be extracted at a profit.

overburden

Overburden is the layer of soil and rock lying above an ore deposit that must be removed to reach the ore in surface mining.

Part 1 done

2

Part 2 of 5: Surface mining strips away land to expose shallow ore

Start with ore that lies close to the ground surface. In surface mining, workers remove vegetation, soil, and rock to expose the deposit. This is usually cheaper than digging underground, and it recovers most of the ore. Three common types are used.

  • In strip mining, long parallel strips of overburden are removed to reach shallow, flat layers such as coal.
  • In open-pit mining, a large pit is dug deeper over time to reach ore such as copper.
  • In mountaintop removal, a summit is blasted off to reach coal, and waste rock often fills nearby valleys.

Key terms · tap one for its definition

surface mining

Surface mining is the extraction of ore that lies close to the ground surface by removing the soil, vegetation, and rock above it.

strip mining

Strip mining is surface mining in which successive long strips of overburden are removed to expose shallow, horizontal layers of ore such as coal.

open-pit mining

Open-pit mining is surface mining in which a large pit is excavated, usually in steps, to reach a concentrated ore deposit near the surface.

Part 2 done

Quick check

One question on the part you just read

Easy

Identify the mining method that removes long, parallel strips of soil and rock to reach shallow, flat layers of coal.
Show answer and explanation

Answer: A · Worked explanation

Strip mining removes successive long strips of overburden to uncover shallow, flat layers such as coal. Open-pit mining also works from the surface, but it digs a deepening pit instead of moving along parallel strips. Mountaintop removal blasts away a summit rather than clearing strips across flat ground.
3

Part 3 of 5: Subsurface mining reaches deep ore through tunnels

Surface methods stop making sense when ore lies far below the ground. Removing that much overburden would cost too much and destroy too much land. Subsurface mining instead digs shafts and tunnels to reach the ore directly. Mines can follow ore hundreds of meters down this way.

Far less land is cleared, but the work carries other costs. Underground mining is more expensive per ton of ore. Workers face cave-ins, explosions from trapped gases, and lung disease from dust. Miners must also ventilate the tunnels to clear dust and gases.

Figure 1. A surface mine removes the overburden above shallow ore, while a subsurface mine reaches deep ore through a shaft and tunnel.

Surface and subsurface mining compared

FeatureSurface miningSubsurface mining
Best suited to ore that isShallowDeep
Land disturbedLarge areaSmall area
Cost per ton of oreUsually lowerUsually higher
Main worker dangersEquipment and blasting accidentsCave-ins, gas explosions, dust
Feature
Best suited to ore that is
Surface mining
Shallow
Subsurface mining
Deep
Feature
Land disturbed
Surface mining
Large area
Subsurface mining
Small area
Feature
Cost per ton of ore
Surface mining
Usually lower
Subsurface mining
Usually higher
Feature
Main worker dangers
Surface mining
Equipment and blasting accidents
Subsurface mining
Cave-ins, gas explosions, dust

Key term

subsurface mining

Subsurface mining is the extraction of deep ore by digging shafts and tunnels instead of removing all the overburden above it.

Part 3 done

4

Part 4 of 5: Mining damages land, water, and air

Now consider what mining leaves behind. Clearing land destroys habitat and exposes soil to erosion. Eroded sediment then washes into streams, making them cloudy and harming aquatic life.

Water is often harmed most. Exposed rock that contains sulfide minerals reacts with air and water to form acid mine drainage. This acidic water carries dissolved metals into streams and groundwater.

Processing ore creates tailings, the finely ground waste left after the valuable minerals are removed. Tailings can hold toxic metals and chemicals. Leaks or dam failures can contaminate large areas. Blasting, dust, and heavy machinery add air pollution and noise.

Exam tip

When you describe an impact, name the cause and the resource harmed. For example, exposed sulfide minerals form acid that lowers stream pH.

Go deeperHow acid mine drainage forms

A common sulfide mineral is pyrite, an iron sulfide with the formula FeS2\mathrm{FeS_2}FeS2​. When air and water reach pyrite, chemical reactions produce sulfuric acid. Bacteria can speed these reactions up.

The acid dissolves other metals from nearby rock. When the water reaches a stream, the stream’s pH drops. Dissolved iron often leaves an orange coating on the streambed, and few aquatic organisms can tolerate the conditions.

Key terms · tap one for its definition

acid mine drainage

Acid mine drainage is acidic water, often carrying dissolved metals, that forms when air and water react with sulfide minerals exposed by mining.

tailings

Tailings are the finely ground waste left after valuable minerals are separated from ore, often stored in ponds and often containing toxic substances.

Part 4 done

Quick check

One question on the part you just read

Easy

What is overburden?
Show answer and explanation

Answer: B · Worked explanation

Overburden is the soil and rock that lies above an ore deposit and must be removed to reach it in surface mining. The finely ground waste left after minerals are separated is tailings, a different material produced later during processing. The rock containing the valuable metal is the ore.
5

Part 5 of 5: Planning, cleanup, and recycling reduce mining damage

Much of this harm can be limited if companies plan for it. The aim is to disturb less land and to repair what is disturbed. Cleanup after mining is called reclamation. It includes regrading the land, replacing topsoil, and replanting native vegetation.

  • Neutralize acidic water, for example with lime, before it leaves the site.
  • Line tailings ponds and cover waste rock to keep air and water out.
  • Require companies to set aside money in advance to pay for cleanup.
  • Recycle metals so that less new ore must be mined.

Common mistake

Reclamation does not fully undo mining. A replanted site rarely matches the original ecosystem, and the removed ore is gone for good.

Key term

reclamation

Reclamation is the process of returning a mined site toward a stable, vegetated condition by regrading land, replacing topsoil, and replanting.

Note read

Check your recall[13 marks]

6 written questions. Answer each one in your head or on paper, then open the mark scheme.

  1. 1.Identify[1 mark]

    Identify the type of mining used to reach ore that lies deep underground.

    Show mark schemeHide mark scheme

    Model answer

    Subsurface mining.

    • 1 mark for identifying subsurface mining
  2. 2.Describe[2 marks]

    Describe how strip mining exposes ore.

    Show mark schemeHide mark scheme

    Model answer

    Long parallel strips of overburden are removed in turn. This uncovers shallow, flat layers of ore such as coal.

    • 1 mark for stating that overburden is removed
    • 1 mark for stating that it is removed in successive long strips to reach shallow ore layers
  3. 3.Explain[3 marks]

    Explain how mining can lower the pH of a nearby stream.

    Show mark schemeHide mark scheme

    Model answer

    Mining exposes rock that contains sulfide minerals. These minerals react with air and water to form acidic water, called acid mine drainage. Runoff or seepage carries the acid into the stream and lowers its pH.

    • 1 mark for stating that mining exposes sulfide minerals
    • 1 mark for stating that they react with air and water to form acid
    • 1 mark for explaining that the acidic water flows into the stream
  4. 4.Describe[2 marks]

    Describe two ways to reduce the environmental harm caused by mining.

    Show mark schemeHide mark scheme

    Model answer

    Reclaim the site by regrading, replacing topsoil, and replanting vegetation. Line tailings ponds to stop toxic seepage. Recycling metals also reduces the need for new ore.

    • 1 mark for describing one valid measure, such as reclamation, neutralizing acidic water, lining tailings ponds, or recycling
    • 1 mark for describing a second valid measure
  5. 5.Justify[3 marks]

    Justify the use of subsurface mining rather than surface mining for a deep ore deposit beneath a forest.

    Show mark schemeHide mark scheme

    Model answer

    Surface mining would need very deep overburden to be removed, which is costly and clears a large area. Subsurface mining reaches the ore through shafts and tunnels. This disturbs far less forest, so there is less habitat loss and erosion.

    • 1 mark for stating that surface mining would remove a large amount of overburden or land
    • 1 mark for stating that subsurface mining disturbs much less surface land
    • 1 mark for linking the smaller disturbance to less habitat loss or erosion
  6. 6.Predict[2 marks]

    Predict how increased metal recycling would affect the amount of new ore that must be mined.

    Show mark schemeHide mark scheme

    Model answer

    Less new ore would be mined because recycled metal replaces some of it. This would also reduce the overburden removed and the tailings produced.

    • 1 mark for predicting that less new ore is mined
    • 1 mark for linking this to less land disturbed or less waste produced

Practice this topic

10 quick-fire multiple-choice questions, easy to hard. Tap an answer to see if you're right and the worked explanation. (The written questions with mark schemes are under “Check your recall” above.)

0 right0 of 10 answered

Includes the 2 quick checks in the note above.

3.

Easy·Identify[1 mark]

Identify an environmental impact that comes directly from clearing land for a surface mine.
Show answer and explanation

Answer: C · Worked explanation

Clearing vegetation and removing soil destroys habitat and leaves bare ground that erodes easily. Ozone thinning, soil salinity from irrigation, and ocean algal growth have other causes and are not direct results of clearing mine land. Eroded sediment can then wash into streams and harm aquatic life.
4.

Medium·Identify[1 mark]

A copper ore body lies 400 m below farmland. A company wants to disturb as little surface land as possible. Identify the most suitable method.
Show answer and explanation

Answer: D · Worked explanation

Reaching ore 400 m down from the surface would mean removing a huge volume of overburden and clearing a wide area of farmland. Subsurface mining reaches the ore through shafts and tunnels and leaves most of the surface intact, which best meets the goal of disturbing little land. Strip mining, open-pit mining, and mountaintop removal all clear large areas of surface land.
5.

Medium·Explain[1 mark]

Explain how acid mine drainage forms.
Show answer and explanation

Answer: D · Worked explanation

Mining exposes rock with sulfide minerals. These react with air and water to produce acid, and the acidic water dissolves metals and flows into streams. Dust from blasting does not make water basic in this way. Fertilizer runoff causes algal growth, which is a different pollution problem.
6.

Medium·Identify[1 mark]

Downstream of an abandoned coal mine, a stream has an orange tint, a pH far below the upstream pH, and few fish. Identify the most likely cause.
Show answer and explanation

Answer: A · Worked explanation

A low pH and an orange coating of dissolved iron point to acid mine drainage from exposed sulfide minerals. Nutrient runoff would cause an algal bloom, usually giving green water rather than very low pH. Warm water would not lower pH or tint the water orange.
7.

Medium·Calculate[1 mark]

A strip mine has disturbed 500 hectares, and 120 hectares have been reclaimed. Calculate the percentage of the disturbed land still unreclaimed.
Show answer and explanation

Answer: C · Worked explanation

Unreclaimed land is 500 − 120 = 380 hectares. As a percentage, 380500×100=76%\frac{380}{500}\times100=76\%500380​×100=76%. The value 24% is the share that has been reclaimed, which is a different quantity. The value 380% results from reporting the hectares as a percentage, and the value 38% has no basis in the data.
8.

Hard[2 marks]

A company proposes replacing an open-pit mine with a subsurface mine for the same ore. Which is the most likely result?
Show answer and explanation

Answer: A · Worked explanation

Subsurface mining clears far less surface land but exposes workers to cave-ins, trapped gases, and dust. Acid mine drainage can still form underground, because tunnels expose sulfide minerals to air and water. Greater habitat loss and lower cost per ton describe surface mining, not the change to underground mining.
9.

Hard[2 marks]

A company regrades a mined site, spreads topsoil, and plants grass. Which statement about this work is most accurate?
Show answer and explanation

Answer: B · Worked explanation

Regrading, topsoil, and plants stabilize the ground and slow erosion, which is the goal of reclamation. The restored site usually differs from the original ecosystem, and water may still need treatment. Reclamation does not bring back removed ore, and it has no effect on tailings made during processing.
10.

Hard·Predict[2 marks]

A mine stores tailings in an unlined pond on permeable soil above groundwater. Predict which change would best reduce contamination of the groundwater.
Show answer and explanation

Answer: A · Worked explanation

A liner stops liquid from seeping through permeable soil, and a cover limits contact with air and rain, so toxic metals stay out of groundwater. Trees do not remove all contaminants. Adding water or enlarging the pond increases the volume or area exposed and can raise seepage rather than prevent it.

Keep going

Next topic5.10 UrbanizationPrevious topic5.8 Overfishing

More in Unit 5 · Land and Water Use

  1. 5.5Irrigation methodsNotes · 10 questions
  2. 5.6Pest control methodsNotes · 10 questions
  3. 5.7Meat production methodsNotes · 10 questions
  4. 5.8OverfishingNotes · 10 questions
  5. 5.9MiningNotes · 10 questions
  6. 5.10UrbanizationNotes · 10 questions
  7. 5.11Ecological footprintsNotes · 10 questions
  8. 5.12Introduction to sustainabilityNotes · 10 questions
  9. 5.13Reducing urban runoffNotes · 10 questions

All AP Environmental Science topics →

Draft: written by Scribe and checked automatically, not yet by a subject reviewer.

Practice questions are original, written by Scribe and checked automatically for correctness.

Topic codes follow the official numbering. Not endorsed by College Board or any exam board.

On this page

0/5 read

  1. 1Mining removes valuable materials from the ground
  2. 2Surface mining strips away land to expose shallow ore
  3. 3Subsurface mining reaches deep ore through tunnels
  4. 4Mining damages land, water, and air
  5. 5Planning, cleanup, and recycling reduce mining damage
  6. Check your recall
  7. Practice: 10 questions
All coursesScribeHow it worksPricingPrivacyTerms

Notes and questions are written by Scribe in our own words. Topic codes follow the official course numbering so you can find your place. Not produced or endorsed by the IB, College Board, AQA, OCR, Pearson Edexcel or any exam board.

© 2026 Scribe