Scribe logoScribeNotes & practice
Sign inStart free
  1. Notes
  2. ›AP Physics 1
  3. ›8 Fluids
  4. ›8.4 Fluids and conservation laws

AP Physics 1 · Unit 8 · Fluids

8.4 Fluids and conservation laws

Apply conservation of mass and Bernoulli's equation to moving fluids, and explain how energy is conserved in their flow.

  • 3 min read
  • 5 parts
  • 10 questions
  • Draft
Start a Quick 5 on this topic→Jump to the 10 questions
1/5The mass entering a pipe must equal the mass leaving
  1. 1The mass entering a pipe must equal the mass leaving
  2. 2A narrower pipe makes the fluid flow faster
  3. 3Energy per unit volume is conserved along a streamline
  4. 4Pressure drops where the fluid speeds up
  5. 5A change in height trades off against pressure and speed
  6. Check your recall
  7. Practice: 10 questions
1

Part 1 of 5: The mass entering a pipe must equal the mass leaving

Think of water flowing steadily through a garden hose. None piles up inside, and none appears from nowhere. The mass entering each second equals the mass leaving each second.

For an incompressible fluid, volume tracks mass. The volume flow rate QQQ is the volume passing a point each second. It equals Q=AvQ=AvQ=Av, where AAA is the cross-sectional area and vvv is the speed.

Key term

volume flow rate

The volume of fluid passing a cross section per unit time, measured in m3/s\mathrm{m^3/s}m3/s.

Part 1 done

2

Part 2 of 5: A narrower pipe makes the fluid flow faster

Since the flow rate is the same everywhere, A1v1=A2v2A_1v_1=A_2v_2A1​v1​=A2​v2​. This is the continuity equation.

Where the pipe narrows, the area falls, so the speed must rise. Where it widens, the speed falls. Putting a thumb over a hose end shows this, as the water shoots out faster.

Worked example

Speed in a narrow section

Water flows at 1.5 m/s1.5\ \mathrm{m/s}1.5 m/s through a pipe of cross-sectional area 0.0020 m20.0020\ \mathrm{m^2}0.0020 m2. The pipe narrows to 0.00050 m20.00050\ \mathrm{m^2}0.00050 m2. Find the speed in the narrow section.
  1. 1
    Use A1v1=A2v2A_1v_1=A_2v_2A1​v1​=A2​v2​, so v2=A1v1A2v_2=\frac{A_1v_1}{A_2}v2​=A2​A1​v1​​.
  2. 2
    Substitute: v2=(0.0020)(1.5)0.00050v_2=\frac{(0.0020)(1.5)}{0.00050}v2​=0.00050(0.0020)(1.5)​.
  3. 3
    Calculate: v2=0.00300.00050=6.0v_2=\frac{0.0030}{0.00050}=6.0v2​=0.000500.0030​=6.0.

Answer: The speed in the narrow section is 6.0 m/s6.0\ \mathrm{m/s}6.0 m/s.

Common mistake

The flow rate stays constant, but the speed does not. Only the product AvAvAv is the same at every section.

Key term

continuity equation

The statement that AvAvAv is constant along a pipe for steady flow of an incompressible fluid.

Part 2 done

Quick check

One question on the part you just read

Easy

Identify the quantity that stays constant along a pipe of changing width in steady flow of an incompressible fluid.
Show answer and explanation

Answer: A · Worked explanation

The volume flow rate is the same at every section, and it equals the area times the speed. The speed changes whenever the area changes, so speed alone is not constant. Pressure also varies along the pipe.
3

Part 3 of 5: Energy per unit volume is conserved along a streamline

Now consider energy. A flowing fluid carries energy through its speed, its height and its pressure. In smooth, steady flow, the total stays constant along the path.

Per unit volume, the three terms are PPP, 12ρv2\frac{1}{2}\rho v^221​ρv2 and ρgy\rho g yρgy. Their sum gives Bernoulli's equation: P+12ρv2+ρgy=constantP+\frac{1}{2}\rho v^2+\rho g y=\text{constant}P+21​ρv2+ρgy=constant.

It applies along a streamline, which is the path followed by a small piece of fluid. Three conditions must hold:

  • The flow is steady
  • The fluid is incompressible
  • Viscosity is negligible

Exam tip

State these conditions when you use the equation. Say which two points lie on the same streamline.

Key terms · tap one for its definition

Bernoulli's equation

The relation P+12ρv2+ρgy=constantP+\frac{1}{2}\rho v^2+\rho g y=\text{constant}P+21​ρv2+ρgy=constant along a streamline in steady, incompressible, nonviscous flow.

streamline

A curve whose tangent at each point gives the fluid velocity there; in steady flow, the path of a fluid element.

Part 3 done

4

Part 4 of 5: Pressure drops where the fluid speeds up

In a horizontal pipe, yyy does not change, so P+12ρv2P+\frac{1}{2}\rho v^2P+21​ρv2 stays constant. Where the speed rises, the pressure must fall.

Energy explains this. Higher pressure behind the fluid pushes it toward the narrow section, where the pressure is lower. The net force does positive work, so the fluid gains kinetic energy.

Figure 1. The fluid moves faster in the narrow section. By Bernoulli's equation, its pressure is lower there.

Worked example

Pressure in a narrow section

Water of density 1000 kg/m31000\ \mathrm{kg/m^3}1000 kg/m3 flows through a horizontal pipe. In the wide section, v1=2.0 m/sv_1=2.0\ \mathrm{m/s}v1​=2.0 m/s and P1=2.00×105 PaP_1=2.00\times10^{5}\ \mathrm{Pa}P1​=2.00×105 Pa. In the narrow section, v2=6.0 m/sv_2=6.0\ \mathrm{m/s}v2​=6.0 m/s. Find P2P_2P2​.
  1. 1
    The pipe is horizontal, so P1+12ρv12=P2+12ρv22P_1+\frac{1}{2}\rho v_1^2=P_2+\frac{1}{2}\rho v_2^2P1​+21​ρv12​=P2​+21​ρv22​.
  2. 2
    Rearrange: P2=P1+12ρ (v12−v22)P_2=P_1+\frac{1}{2}\rho\,(v_1^2-v_2^2)P2​=P1​+21​ρ(v12​−v22​).
  3. 3
    Substitute: P2=200000+12(1000)(4.0−36)P_2=200000+\frac{1}{2}(1000)(4.0-36)P2​=200000+21​(1000)(4.0−36).
  4. 4
    Calculate: P2=200000−16000=184000P_2=200000-16000=184000P2​=200000−16000=184000.

Answer: The pressure is P2=1.84×105 PaP_2=1.84\times10^{5}\ \mathrm{Pa}P2​=1.84×105 Pa.

Common mistake

Faster flow does not mean higher pressure. In a horizontal pipe, the fastest section has the lowest pressure.

Part 4 done

Quick check

One question on the part you just read

Easy

Identify the term in Bernoulli's equation that represents kinetic energy per unit volume.
Show answer and explanation

Answer: A · Worked explanation

Kinetic energy is 12mv2\frac{1}{2}mv^221​mv2. Dividing by volume turns mmm into the density ρ\rhoρ, giving 12ρv2\frac{1}{2}\rho v^221​ρv2. The term ρgy\rho g yρgy is gravitational potential energy per unit volume.
5

Part 5 of 5: A change in height trades off against pressure and speed

Now let the fluid change height. A fluid that rises gains potential energy, so its pressure or speed must fall. Moving downward does the reverse. Pressure therefore drops as water climbs a pipe, even if its speed stays the same.

Consider a large open tank draining through a small hole. The surface and the hole are both at atmospheric pressure. The surface speed is nearly zero, so ρgh=12ρv2\rho g h=\frac{1}{2}\rho v^2ρgh=21​ρv2 and v=2ghv=\sqrt{2gh}v=2gh​.

Worked example

Draining tank

Water leaves a small hole 1.8 m1.8\ \mathrm{m}1.8 m below the surface of a large open tank. Find the exit speed. Use g=9.8 m/s2g=9.8\ \mathrm{m/s^2}g=9.8 m/s2.
  1. 1
    Surface and hole are both at atmospheric pressure, and the surface speed is about zero.
  2. 2
    So v=2ghv=\sqrt{2gh}v=2gh​.
  3. 3
    Calculate: v=2(9.8)(1.8)=35.28=5.94v=\sqrt{2(9.8)(1.8)}=\sqrt{35.28}=5.94v=2(9.8)(1.8)​=35.28​=5.94.

Answer: The exit speed is 5.9 m/s5.9\ \mathrm{m/s}5.9 m/s.

Note read

Check your recall[13 marks]

5 written questions. Answer each one in your head or on paper, then open the mark scheme.

  1. 1.State[3 marks]

    State the continuity equation for an incompressible fluid and define each symbol.

    Show mark schemeHide mark scheme

    Model answer

    A1v1=A2v2A_1v_1=A_2v_2A1​v1​=A2​v2​, where AAA is the cross-sectional area of the pipe and vvv is the fluid speed at that section. Subscripts 1 and 2 label two sections.

    • 1 mark for writing A1v1=A2v2A_1v_1=A_2v_2A1​v1​=A2​v2​
    • 1 mark for defining AAA as cross-sectional area
    • 1 mark for defining vvv as fluid speed (subscripts label sections)
  2. 2.Calculate[2 marks]

    Calculate the speed in a section of area 0.0040 m20.0040\ \mathrm{m^2}0.0040 m2 when water at 3.0 m/s3.0\ \mathrm{m/s}3.0 m/s flows in from a section of area 0.0010 m20.0010\ \mathrm{m^2}0.0010 m2.

    Show mark schemeHide mark scheme

    Model answer

    v2=A1v1A2=(0.0010)(3.0)0.0040=0.75 m/sv_2=\frac{A_1v_1}{A_2}=\frac{(0.0010)(3.0)}{0.0040}=0.75\ \mathrm{m/s}v2​=A2​A1​v1​​=0.0040(0.0010)(3.0)​=0.75 m/s.

    • 1 mark for using A1v1=A2v2A_1v_1=A_2v_2A1​v1​=A2​v2​
    • 1 mark for obtaining 0.75 m/s0.75\ \mathrm{m/s}0.75 m/s
  3. 3.Explain[3 marks]

    Explain, using energy, why the pressure falls in the narrow section of a horizontal pipe.

    Show mark schemeHide mark scheme

    Model answer

    The fluid moves faster in the narrow section, so its kinetic energy per volume is higher. The height does not change. Total energy per volume is conserved, so the pressure term must be lower.

    • 1 mark for stating that speed is higher in the narrow section (greater kinetic energy)
    • 1 mark for stating that height is unchanged
    • 1 mark for linking conservation of energy per volume to a lower pressure
  4. 4.State[2 marks]

    State two conditions needed for Bernoulli's equation to apply.

    Show mark schemeHide mark scheme

    Model answer

    The flow must be steady, the fluid must be incompressible, and viscosity must be negligible. Points must lie on one streamline. Any two of these.

    • 1 mark for stating one valid condition
    • 1 mark for stating a second valid condition
  5. 5.Calculate[3 marks]

    Calculate the exit speed of water from a small hole 0.80 m0.80\ \mathrm{m}0.80 m below the surface of a large open tank.

    Show mark schemeHide mark scheme

    Model answer

    v=2gh=2(9.8)(0.80)=15.68≈4.0 m/sv=\sqrt{2gh}=\sqrt{2(9.8)(0.80)}=\sqrt{15.68}\approx4.0\ \mathrm{m/s}v=2gh​=2(9.8)(0.80)​=15.68​≈4.0 m/s.

    • 1 mark for using ρgh=12ρv2\rho g h=\frac{1}{2}\rho v^2ρgh=21​ρv2 or v=2ghv=\sqrt{2gh}v=2gh​
    • 1 mark for substituting g=9.8g=9.8g=9.8 and h=0.80h=0.80h=0.80
    • 1 mark for obtaining about 4.0 m/s4.0\ \mathrm{m/s}4.0 m/s

Practice this topic

10 quick-fire multiple-choice questions, easy to hard. Tap an answer to see if you're right and the worked explanation. (The written questions with mark schemes are under “Check your recall” above.)

0 right0 of 10 answered

Includes the 2 quick checks in the note above.

3.

Easy·Predict[1 mark]

Predict what happens to the speed of a steadily flowing, incompressible fluid when the pipe it flows in becomes narrower.
Show answer and explanation

Answer: A · Worked explanation

The product of area and speed is constant, so a smaller area requires a larger speed. A decrease in speed would occur in a wider pipe, not a narrower one.
4.

Medium·Calculate[1 mark]

Water flows at 0.50 m s−10.50\ \mathrm{m\,s^{-1}}0.50 ms−1 through a pipe of area 0.0060 m20.0060\ \mathrm{m^2}0.0060 m2 into a section of area 0.0020 m20.0020\ \mathrm{m^2}0.0020 m2. Calculate the speed in the narrow section.
Show answer and explanation

Answer: A · Worked explanation

v2=A1v1A2=(0.0060)(0.50)0.0020=1.5 m s−1v_2=\frac{A_1v_1}{A_2}=\frac{(0.0060)(0.50)}{0.0020}=1.5\ \mathrm{m\,s^{-1}}v2​=A2​A1​v1​​=0.0020(0.0060)(0.50)​=1.5 ms−1. The value 0.17 m s−10.17\ \mathrm{m\,s^{-1}}0.17 ms−1 inverts the area ratio, so it predicts a slower flow in the narrower pipe, which is wrong.
5.

Medium·Calculate[2 marks]

A pipe's radius decreases from 4.0 cm to 2.0 cm. The speed in the wide part is 1.0 m s−11.0\ \mathrm{m\,s^{-1}}1.0 ms−1. Calculate the speed in the narrow part.
Show answer and explanation

Answer: D · Worked explanation

Area is proportional to r2r^2r2, so halving the radius gives one quarter of the area. Then v2=4v1=4.0 m s−1v_2=4v_1=4.0\ \mathrm{m\,s^{-1}}v2​=4v1​=4.0 ms−1. The value 2.0 m s−12.0\ \mathrm{m\,s^{-1}}2.0 ms−1 treats area as proportional to radius.
6.

Medium·Calculate[2 marks]

Water of density 1000 kg m−31000\ \mathrm{kg\,m^{-3}}1000 kgm−3 flows through a horizontal pipe. At one point P=1.50×105 PaP=1.50\times10^{5}\ \mathrm{Pa}P=1.50×105 Pa and v=3.0 m s−1v=3.0\ \mathrm{m\,s^{-1}}v=3.0 ms−1. Calculate the pressure where v=5.0 m s−1v=5.0\ \mathrm{m\,s^{-1}}v=5.0 ms−1.
Show answer and explanation

Answer: D · Worked explanation

P2=P1+12ρ(v12−v22)=150000+500(9−25)=142000 PaP_2=P_1+\frac{1}{2}\rho(v_1^2-v_2^2)=150000+500(9-25)=142000\ \mathrm{Pa}P2​=P1​+21​ρ(v12​−v22​)=150000+500(9−25)=142000 Pa. The value 1.38×105 Pa1.38\times10^{5}\ \mathrm{Pa}1.38×105 Pa comes from using only v22v_2^2v22​ and leaving out the initial speed.
7.

Medium·Calculate[2 marks]

Water leaves a small hole 5.0 m below the surface of a large open tank. Calculate the exit speed. Use g=9.8 m s−2g=9.8\ \mathrm{m\,s^{-2}}g=9.8 ms−2.
Show answer and explanation

Answer: C · Worked explanation

v=2gh=2(9.8)(5.0)=98≈9.9 m s−1v=\sqrt{2gh}=\sqrt{2(9.8)(5.0)}=\sqrt{98}\approx9.9\ \mathrm{m\,s^{-1}}v=2gh​=2(9.8)(5.0)​=98​≈9.9 ms−1. The exit speed rises with depth. The value 7.0 m s−17.0\ \mathrm{m\,s^{-1}}7.0 ms−1 is gh\sqrt{gh}gh​, which drops the factor of 2 that comes from the one-half.
8.

Hard·Determine[2 marks]

Water of density 1000 kg m−31000\ \mathrm{kg\,m^{-3}}1000 kgm−3 flows through a pipe of constant width. It rises 3.0 m, and the pressure at the lower point is 3.0×105 Pa3.0\times10^{5}\ \mathrm{Pa}3.0×105 Pa. Determine the pressure at the higher point. Use g=9.8 m s−2g=9.8\ \mathrm{m\,s^{-2}}g=9.8 ms−2.
Show answer and explanation

Answer: D · Worked explanation

The width is constant, so the speed is unchanged and only P+ρgyP+\rho g yP+ρgy matters. Then P2=3.0×105−(1000)(9.8)(3.0)=2.7×105 PaP_2=3.0\times10^{5}-(1000)(9.8)(3.0)=2.7\times10^{5}\ \mathrm{Pa}P2​=3.0×105−(1000)(9.8)(3.0)=2.7×105 Pa. The value 3.0×105 Pa3.0\times10^{5}\ \mathrm{Pa}3.0×105 Pa ignores the change in height. Rising water gains potential energy, so its pressure must fall.
9.

Hard·Determine[2 marks]

Water of density 1000 kg m−31000\ \mathrm{kg\,m^{-3}}1000 kgm−3 flows at 2.0 m s−12.0\ \mathrm{m\,s^{-1}}2.0 ms−1 through a horizontal pipe of area 0.0100 m20.0100\ \mathrm{m^2}0.0100 m2 and pressure 2.50×105 Pa2.50\times10^{5}\ \mathrm{Pa}2.50×105 Pa. The pipe narrows to 0.0025 m20.0025\ \mathrm{m^2}0.0025 m2. Determine the pressure there.
Show answer and explanation

Answer: B · Worked explanation

Continuity gives v2=(0.0100)(2.0)0.0025=8.0 m s−1v_2=\frac{(0.0100)(2.0)}{0.0025}=8.0\ \mathrm{m\,s^{-1}}v2​=0.0025(0.0100)(2.0)​=8.0 ms−1. Then P2=250000−12(1000)(64−4)=220000 PaP_2=250000-\frac{1}{2}(1000)(64-4)=220000\ \mathrm{Pa}P2​=250000−21​(1000)(64−4)=220000 Pa. The value 2.80×105 Pa2.80\times10^{5}\ \mathrm{Pa}2.80×105 Pa adds the kinetic term instead of subtracting it. That wrongly raises the pressure where the water speeds up.
10.

Hard·Explain[1 mark]

Water in a horizontal pipe passes from a wide section into a narrow section. Which statement correctly explains the energy of the water?
Show answer and explanation

Answer: A · Worked explanation

In the narrow section the pressure is lower. The higher pressure behind pushes the water forward with a net force. That force does positive work, raising kinetic energy. The pipe is horizontal, so there is no change in gravitational potential energy to supply the gain.

Keep going

Previous topic8.3 Fluids and Newton's laws

More in Unit 8 · Fluids

  1. 8.1Internal structure and densityNotes · 10 questions
  2. 8.2PressureNotes · 10 questions
  3. 8.3Fluids and Newton's lawsNotes · 10 questions
  4. 8.4Fluids and conservation lawsNotes · 10 questions

All AP Physics 1 topics →

Draft: written by Scribe and checked automatically, not yet by a subject reviewer.

Practice questions are original, written by Scribe and checked automatically for correctness.

Topic codes follow the official numbering. Not endorsed by College Board or any exam board.

On this page

0/5 read

  1. 1The mass entering a pipe must equal the mass leaving
  2. 2A narrower pipe makes the fluid flow faster
  3. 3Energy per unit volume is conserved along a streamline
  4. 4Pressure drops where the fluid speeds up
  5. 5A change in height trades off against pressure and speed
  6. Check your recall
  7. Practice: 10 questions
All coursesScribeHow it worksPricingPrivacyTerms

Notes and questions are written by Scribe in our own words. Topic codes follow the official course numbering so you can find your place. Not produced or endorsed by the IB, College Board, AQA, OCR, Pearson Edexcel or any exam board.

© 2026 Scribe