Scribe logoScribeNotes & practice
Sign inStart free
  1. Notes
  2. ›AQA A-level Physics
  3. ›3.11 Option: Engineering physics
  4. ›3.11.2 Thermodynamics and engines

AQA A-level Physics · Section 3.11 · Option: Engineering physics

3.11.2 Thermodynamics and engines

Apply the first law to a gas, read work done from pV diagrams, and calculate the efficiency of heat engines.

  • 6 min read
  • 6 parts
  • 10 questions
  • Draft
Start a Quick 5 on this topic→Jump to the 10 questions
1/6Heat and work both change the internal energy of a gas
  1. 1Heat and work both change the internal energy of a gas
  2. 2The first law says energy is conserved in these transfers
  3. 3On a pV diagram the area represents work done
  4. 4A heat engine turns some heat input into useful work
  5. 5The temperatures of hot and cold reservoirs limit efficiency
  6. 6Petrol and diesel engines differ in how they add heat
  7. Check your recall
  8. Practice: 10 questions
1

Part 1 of 6: Heat and work both change the internal energy of a gas

A bicycle pump gets warm as you push the plunger in. You do work on the air, and its molecules move faster. The energy stored in the gas has increased.

The internal energy of a gas is the sum of the random kinetic and potential energies of its molecules. Energy can enter the gas as heat, because of a temperature difference. It can also enter as work done on the gas, as when a piston compresses it.

At constant pressure ppp, a gas that expands by ΔV\Delta VΔV does work W=pΔVW=p\Delta VW=pΔV on its surroundings. With ppp in pascals and VVV in cubic metres, WWW is in joules.

Key terms · tap one for its definition

internal energy

The internal energy of a system is the sum of the random kinetic and potential energies of its molecules.

heat

Heat is energy transferred across a system boundary because of a temperature difference.

work done

Work done by a force is the energy transferred when its component along a displacement acts through that displacement.

Part 1 done

2

Part 2 of 6: The first law says energy is conserved in these transfers

Suppose you heat a gas and let it expand. Some of the heat raises the internal energy, and the rest leaves as work. The first law of thermodynamics states this as an equation: Q=ΔU+WQ=\Delta U+WQ=ΔU+W.

Here QQQ is the heat supplied to the gas and ΔU\Delta UΔU is the increase in its internal energy. The work done by the gas is WWW. Heat leaving the gas makes QQQ negative. Work done on the gas makes WWW negative.

Worked example

Using the first law

A gas at constant pressure 1.5×105 Pa1.5\times10^{5}\,\mathrm{Pa}1.5×105Pa expands from 2.0×10−3 m32.0\times10^{-3}\,\mathrm{m^3}2.0×10−3m3 to 5.0×10−3 m35.0\times10^{-3}\,\mathrm{m^3}5.0×10−3m3. It absorbs 700 J700\,\mathrm{J}700J of heat. Calculate the change in its internal energy.
  1. 1
    Work done by the gas = pressure × change in volume, so W=pΔVW=p\Delta VW=pΔV.
  2. 2
    Substitute: W=1.5×105×(5.0×10−3−2.0×10−3)=450 JW=1.5\times10^{5}\times(5.0\times10^{-3}-2.0\times10^{-3})=450\,\mathrm{J}W=1.5×105×(5.0×10−3−2.0×10−3)=450J.
  3. 3
    Rearrange the first law: ΔU=Q−W=700−450\Delta U=Q-W=700-450ΔU=Q−W=700−450.
  4. 4
    Calculate: ΔU=+250 J\Delta U=+250\,\mathrm{J}ΔU=+250J.

Answer: The internal energy rises by 250 J250\,\mathrm{J}250J.

Two special changes remove a term. An isothermal change happens at constant temperature. An adiabatic change involves no heat flow into or out of the gas. For a gas with no forces between its molecules, internal energy depends only on temperature.

Special changes of a gas and the first law

ChangeConditionResult
IsothermalConstant temperatureΔU=0\Delta U=0ΔU=0, so Q=WQ=WQ=W
AdiabaticQ=0Q=0Q=0W=−ΔUW=-\Delta UW=−ΔU
Constant volumeΔV=0\Delta V=0ΔV=0W=0W=0W=0, so Q=ΔUQ=\Delta UQ=ΔU
Constant pressureppp fixedW=pΔVW=p\Delta VW=pΔV
Change
Isothermal
Condition
Constant temperature
Result
ΔU=0\Delta U=0ΔU=0, so Q=WQ=WQ=W
Change
Adiabatic
Condition
Q=0Q=0Q=0
Result
W=−ΔUW=-\Delta UW=−ΔU
Change
Constant volume
Condition
ΔV=0\Delta V=0ΔV=0
Result
W=0W=0W=0, so Q=ΔUQ=\Delta UQ=ΔU
Change
Constant pressure
Condition
ppp fixed
Result
W=pΔVW=p\Delta VW=pΔV

Key terms · tap one for its definition

first law of thermodynamics

The first law states that a system’s internal energy changes through heat transfer and work, conserving energy.

isothermal change

An isothermal change is a change of a gas that takes place at constant temperature.

adiabatic change

An adiabatic change is a change in which no heat enters or leaves the gas.

Part 2 done

Quick check

One question on the part you just read

Easy

Identify what WWW represents in the first law, Q=ΔU+WQ=\Delta U+WQ=ΔU+W.
Show answer and explanation

Answer: A · Worked explanation

In this form of the law WWW is the work done by the gas, so it is positive when the gas expands. Work done on the gas would make WWW negative. The increase in internal energy is ΔU\Delta UΔU, and heat supplied is QQQ.
3

Part 3 of 6: On a pV diagram the area represents work done

Engines repeat the same changes again and again. A pV diagram plots pressure against volume, so each change becomes a line or curve. The area under an expansion curve equals the work done by the gas. For compression, the area is the work done on the gas. A larger pressure or a larger volume change gives a larger area.

A complete cycle returns to its starting point, so the enclosed area is the net work done per cycle. A clockwise loop gives net work output, as in an engine. An anticlockwise loop means net work is done on the gas.

Figure 1. The enclosed area of a clockwise loop is the net work done by the gas in one cycle.

Worked example

Net work from a cycle

A cycle is a rectangle on a pV diagram. Pressure runs from 1.0×105 Pa1.0\times10^{5}\,\mathrm{Pa}1.0×105Pa to 3.0×105 Pa3.0\times10^{5}\,\mathrm{Pa}3.0×105Pa and volume from 1.0×10−3 m31.0\times10^{-3}\,\mathrm{m^3}1.0×10−3m3 to 3.0×10−3 m33.0\times10^{-3}\,\mathrm{m^3}3.0×10−3m3. Calculate the net work done per cycle.
  1. 1
    Net work = enclosed area = pressure range × volume range.
  2. 2
    Substitute: (3.0×105−1.0×105)×(3.0×10−3−1.0×10−3)(3.0\times10^{5}-1.0\times10^{5})\times(3.0\times10^{-3}-1.0\times10^{-3})(3.0×105−1.0×105)×(3.0×10−3−1.0×10−3).
  3. 3
    Calculate: 2.0×105×2.0×10−3=400 J2.0\times10^{5}\times2.0\times10^{-3}=400\,\mathrm{J}2.0×105×2.0×10−3=400J.

Answer: The net work done per cycle is 400 J400\,\mathrm{J}400J.

Key term

pV diagram

A pV diagram is a graph of the pressure of a gas against its volume.

Part 3 done

4

Part 4 of 6: A heat engine turns some heat input into useful work

An engine must take in heat to produce work. A heat engine takes heat QHQ_\mathrm{H}QH​ from a hot source and does work WWW. It rejects heat QCQ_\mathrm{C}QC​ to a cold sink. Hot gas expands and pushes a piston, which gives mechanical work. The gas must then be cooled and compressed, so some heat is always rejected.

The gas returns to its starting state each cycle, so its internal energy is unchanged. The first law then gives W=QH−QCW=Q_\mathrm{H}-Q_\mathrm{C}W=QH​−QC​. The efficiency is the fraction of the heat input that becomes useful work: WQH\frac{W}{Q_\mathrm{H}}QH​W​.

Worked example

Efficiency of an engine

In one cycle an engine takes 2000 J2000\,\mathrm{J}2000J from a hot source and rejects 1400 J1400\,\mathrm{J}1400J to a cold sink. Calculate its efficiency.
  1. 1
    Work done = heat in − heat out, so W=QH−QC=2000−1400=600 JW=Q_\mathrm{H}-Q_\mathrm{C}=2000-1400=600\,\mathrm{J}W=QH​−QC​=2000−1400=600J.
  2. 2
    Efficiency = WQH\frac{W}{Q_\mathrm{H}}QH​W​.
  3. 3
    Substitute: 6002000=0.30\frac{600}{2000}=0.302000600​=0.30.

Answer: The efficiency is 0.30, or 30%.

Exam tip

Efficiency is a ratio, so it has no unit. Give it as a decimal or a percentage.

Key terms · tap one for its definition

heat engine

A heat engine is a device that takes in heat from a hot source, does work, and rejects heat to a cold sink.

efficiency

Efficiency is the useful work output of an engine divided by its heat input, a ratio with no unit.

Part 4 done

Quick check

One question on the part you just read

Easy

Identify the change in which the temperature of a gas stays constant.
Show answer and explanation

Answer: B · Worked explanation

An isothermal change takes place at constant temperature, so the internal energy of the gas stays the same. In an adiabatic compression no heat flows, but work done on the gas raises its temperature. Heating at constant volume or at constant pressure also raises the temperature of the gas.
5

Part 5 of 6: The temperatures of hot and cold reservoirs limit efficiency

No engine can turn all its heat input into work. The best possible efficiency depends on the absolute temperatures of the hot source and the cold sink. The maximum theoretical efficiency is TH−TCTH\frac{T_\mathrm{H}-T_\mathrm{C}}{T_\mathrm{H}}TH​TH​−TC​​.

Both temperatures must be in kelvin. Raising THT_\mathrm{H}TH​ or lowering TCT_\mathrm{C}TC​ raises the limit, because a larger temperature difference lets more of the heat become work. A limit of 1 would need TC=0 KT_\mathrm{C}=0\,\mathrm{K}TC​=0K, which cannot be reached. Real engines fall below it because of friction, heat losses and incomplete combustion.

Worked example

Limit on efficiency

An engine works between 227 ∘C227\,^{\circ}\mathrm{C}227∘C and 27 ∘C27\,^{\circ}\mathrm{C}27∘C. Calculate its maximum theoretical efficiency.
  1. 1
    Convert to kelvin: TH=227+273=500 KT_\mathrm{H}=227+273=500\,\mathrm{K}TH​=227+273=500K and TC=27+273=300 KT_\mathrm{C}=27+273=300\,\mathrm{K}TC​=27+273=300K.
  2. 2
    Maximum efficiency = TH−TCTH\frac{T_\mathrm{H}-T_\mathrm{C}}{T_\mathrm{H}}TH​TH​−TC​​.
  3. 3
    Substitute: 500−300500=0.40\frac{500-300}{500}=0.40500500−300​=0.40.

Answer: The maximum theoretical efficiency is 0.40, or 40%.

Common mistake

Celsius temperatures give a wrong limit. Here they would give 200227≈0.88\frac{200}{227}\approx0.88227200​≈0.88, which is far too high.

Key term

maximum theoretical efficiency

The maximum theoretical efficiency of an engine between absolute temperatures THT_\mathrm{H}TH​ and TCT_\mathrm{C}TC​ is TH−TCTH\frac{T_\mathrm{H}-T_\mathrm{C}}{T_\mathrm{H}}TH​TH​−TC​​.

Part 5 done

6

Part 6 of 6: Petrol and diesel engines differ in how they add heat

Real engines use gas cycles built from the changes already met. The Otto cycle models a petrol engine. The gas is compressed adiabatically, heated at constant volume by the spark, expanded adiabatically, then cooled at constant volume. These four changes repeat many times each second.

The diesel cycle models a diesel engine. Only air is compressed, to a high pressure and temperature, and fuel is then injected into it. Heat is added at constant pressure as the fuel burns. The other three changes match the Otto cycle.

Idealised petrol and diesel cycles compared

FeatureOtto cycle (petrol)Diesel cycle
Gas compressedFuel–air mixtureAir only
IgnitionSparkHeat of compression
Heating stepConstant volumeConstant pressure
Usual efficiencyLowerHigher
Feature
Gas compressed
Otto cycle (petrol)
Fuel–air mixture
Diesel cycle
Air only
Feature
Ignition
Otto cycle (petrol)
Spark
Diesel cycle
Heat of compression
Feature
Heating step
Otto cycle (petrol)
Constant volume
Diesel cycle
Constant pressure
Feature
Usual efficiency
Otto cycle (petrol)
Lower
Diesel cycle
Higher

Key terms · tap one for its definition

Otto cycle

The Otto cycle is the idealised petrol-engine cycle of adiabatic compression, constant-volume heating, adiabatic expansion and constant-volume cooling.

diesel cycle

The diesel cycle is the idealised diesel-engine cycle with constant-pressure heating in place of the constant-volume heating of the Otto cycle.

Note read

Check your recall[16 marks]

6 written questions. Answer each one in your head or on paper, then open the mark scheme.

  1. 1.State[3 marks]

    State the first law of thermodynamics as an equation and give the meaning of each symbol.

    Show mark schemeHide mark scheme

    Model answer

    Q=ΔU+WQ=\Delta U+WQ=ΔU+W, where QQQ is the heat supplied to the gas, ΔU\Delta UΔU is the increase in its internal energy and WWW is the work done by the gas.

    • 1 mark for writing Q=ΔU+WQ=\Delta U+WQ=ΔU+W
    • 1 mark for stating that QQQ is the heat supplied to the gas and ΔU\Delta UΔU is the increase in internal energy
    • 1 mark for stating that WWW is the work done by the gas
  2. 2.Calculate[3 marks]

    Calculate the change in internal energy of a gas that expands at a constant pressure of 2.0×105 Pa2.0\times10^{5}\,\mathrm{Pa}2.0×105Pa from 1.5×10−3 m31.5\times10^{-3}\,\mathrm{m^3}1.5×10−3m3 to 4.0×10−3 m34.0\times10^{-3}\,\mathrm{m^3}4.0×10−3m3 while absorbing 800 J800\,\mathrm{J}800J of heat.

    Show mark schemeHide mark scheme

    Model answer

    W=pΔV=2.0×105×2.5×10−3=500 JW=p\Delta V=2.0\times10^{5}\times2.5\times10^{-3}=500\,\mathrm{J}W=pΔV=2.0×105×2.5×10−3=500J. Then ΔU=Q−W=800−500=+300 J\Delta U=Q-W=800-500=+300\,\mathrm{J}ΔU=Q−W=800−500=+300J.

    • 1 mark for using W=pΔVW=p\Delta VW=pΔV with ΔV=2.5×10−3 m3\Delta V=2.5\times10^{-3}\,\mathrm{m^3}ΔV=2.5×10−3m3
    • 1 mark for obtaining W=500 JW=500\,\mathrm{J}W=500J
    • 1 mark for using ΔU=Q−W\Delta U=Q-WΔU=Q−W to obtain +300 J+300\,\mathrm{J}+300J
  3. 3.Explain[3 marks]

    Explain how the net work done by a gas in one cycle can be found from a pV diagram.

    Show mark schemeHide mark scheme

    Model answer

    The work done by the gas in an expansion is the area under the curve, and the work done on it in a compression is the area under that curve. The net work is the difference between them. This equals the area enclosed by the loop.

    • 1 mark for stating that work done is the area under a curve on a pV diagram
    • 1 mark for stating that expansion gives work done by the gas and compression gives work done on it
    • 1 mark for concluding that the net work is the area enclosed by the cycle
  4. 4.Calculate[2 marks]

    Calculate the efficiency of an engine that takes 3000 J3000\,\mathrm{J}3000J from a hot source and rejects 2100 J2100\,\mathrm{J}2100J to a cold sink in one cycle.

    Show mark schemeHide mark scheme

    Model answer

    W=3000−2100=900 JW=3000-2100=900\,\mathrm{J}W=3000−2100=900J, so efficiency =9003000=0.30=\frac{900}{3000}=0.30=3000900​=0.30.

    • 1 mark for finding the work done as 900 J900\,\mathrm{J}900J
    • 1 mark for dividing by the heat input to obtain 0.30
  5. 5.Compare[3 marks]

    Compare the idealised Otto cycle with the diesel cycle.

    Show mark schemeHide mark scheme

    Model answer

    The Otto cycle compresses a fuel–air mixture and is ignited by a spark, whereas the diesel cycle compresses air only and the fuel ignites from the heat of compression. Heat is added at constant volume in the Otto cycle and at constant pressure in the diesel cycle.

    • 1 mark for stating that the Otto cycle compresses a fuel–air mixture and the diesel cycle compresses air only
    • 1 mark for stating that ignition is by spark in the Otto cycle and by heat of compression in the diesel cycle
    • 1 mark for stating that heating is at constant volume in the Otto cycle and at constant pressure in the diesel cycle
  6. 6.Suggest[2 marks]

    Suggest two reasons why a real engine has a lower efficiency than its maximum theoretical efficiency.

    Show mark schemeHide mark scheme

    Model answer

    Friction between moving parts wastes energy as heat. Heat is also lost to the surroundings, and combustion may be incomplete.

    • 1 mark for friction between moving parts
    • 1 mark for heat losses to the surroundings or incomplete combustion

Practice this topic

10 quick-fire multiple-choice questions, easy to hard. Tap an answer to see if you're right and the worked explanation. (The written questions with mark schemes are under “Check your recall” above.)

0 right0 of 10 answered

Includes the 2 quick checks in the note above.

3.

Easy·State[1 mark]

State what the area under an expansion curve on a pV diagram represents.
Show answer and explanation

Answer: C · Worked explanation

Area under the curve equals ∫p dV\int p\,\mathrm{d}V∫pdV, which is the work done by the gas. Heat supplied and internal energy are not read from this area. Efficiency is a ratio of work to heat input and has no unit, so it cannot be an area.
4.

Medium·Calculate[1 mark]

A gas at constant pressure 1.2×105 Pa1.2\times10^{5}\,\mathrm{Pa}1.2×105Pa expands from 3.0×10−3 m33.0\times10^{-3}\,\mathrm{m^3}3.0×10−3m3 to 5.0×10−3 m35.0\times10^{-3}\,\mathrm{m^3}5.0×10−3m3. Calculate the work done by the gas.
Show answer and explanation

Answer: D · Worked explanation

At constant pressure, W=pΔV=1.2×105×(5.0×10−3−3.0×10−3)=240 JW=p\Delta V=1.2\times10^{5}\times(5.0\times10^{-3}-3.0\times10^{-3})=240\,\mathrm{J}W=pΔV=1.2×105×(5.0×10−3−3.0×10−3)=240J. The value 360 J360\,\mathrm{J}360J uses the initial volume instead of the change in volume. The value 600 J600\,\mathrm{J}600J uses the final volume. The value 6.0×107 J6.0\times10^{7}\,\mathrm{J}6.0×107J divides pressure by the change in volume. The units pascal and cubic metre combine to give joules.
5.

Medium·Calculate[1 mark]

A gas absorbs 600 J600\,\mathrm{J}600J of heat and does 250 J250\,\mathrm{J}250J of work on its surroundings. Calculate the change in its internal energy.
Show answer and explanation

Answer: C · Worked explanation

Rearranging the first law gives ΔU=Q−W=600−250=+350 J\Delta U=Q-W=600-250=+350\,\mathrm{J}ΔU=Q−W=600−250=+350J, because the gas does work on its surroundings. The value +850 J+850\,\mathrm{J}+850J adds the work instead of subtracting it. The value −350 J-350\,\mathrm{J}−350J has the wrong sign, and +600 J+600\,\mathrm{J}+600J ignores the work done by the gas altogether.
6.

Medium·Calculate[1 mark]

In one cycle an engine takes 4000 J4000\,\mathrm{J}4000J from a hot source and rejects 2800 J2800\,\mathrm{J}2800J to a cold sink. Calculate its efficiency.
Show answer and explanation

Answer: B · Worked explanation

The work done is 4000−2800=1200 J4000-2800=1200\,\mathrm{J}4000−2800=1200J, so efficiency =WQH=12004000=0.30=\frac{W}{Q_\mathrm{H}}=\frac{1200}{4000}=0.30=QH​W​=40001200​=0.30. The value 0.70 is the fraction of the heat that is rejected, and 0.43 is the work divided by the heat rejected. The value 3.3 is the heat input divided by the work.
7.

Medium·Calculate[1 mark]

An engine works between 177 ∘C177\,^{\circ}\mathrm{C}177∘C and 27 ∘C27\,^{\circ}\mathrm{C}27∘C. Calculate its maximum theoretical efficiency.
Show answer and explanation

Answer: D · Worked explanation

In kelvin, TH=177+273=450 KT_\mathrm{H}=177+273=450\,\mathrm{K}TH​=177+273=450K and TC=27+273=300 KT_\mathrm{C}=27+273=300\,\mathrm{K}TC​=27+273=300K. The limit is then 450−300450=0.33\frac{450-300}{450}=0.33450450−300​=0.33. The value 0.85 comes from using Celsius temperatures. The value 0.67 is TCTH\frac{T_\mathrm{C}}{T_\mathrm{H}}TH​TC​​, and 0.50 divides by TCT_\mathrm{C}TC​ instead of THT_\mathrm{H}TH​. Always convert to kelvin before using the formula, because the formula needs absolute temperatures.
8.

Hard·Determine[2 marks]

A gas follows a clockwise rectangular cycle on a pV diagram. Pressure varies from 1.0×105 Pa1.0\times10^{5}\,\mathrm{Pa}1.0×105Pa to 4.0×105 Pa4.0\times10^{5}\,\mathrm{Pa}4.0×105Pa and volume from 2.0×10−3 m32.0\times10^{-3}\,\mathrm{m^3}2.0×10−3m3 to 5.0×10−3 m35.0\times10^{-3}\,\mathrm{m^3}5.0×10−3m3. Determine the net work done by the gas per cycle.
Show answer and explanation

Answer: A · Worked explanation

The enclosed area is 3.0×105×3.0×10−3=900 J3.0\times10^{5}\times3.0\times10^{-3}=900\,\mathrm{J}3.0×105×3.0×10−3=900J, and a clockwise loop means net work is done by the gas. An anticlockwise loop would give −900 J-900\,\mathrm{J}−900J. The value 1200 J1200\,\mathrm{J}1200J is only the area under the top edge. The internal energy returns to its start, but the net work is not zero because heat flows.
9.

Hard·Explain[2 marks]

A gas is compressed adiabatically. Which statement is correct?
Show answer and explanation

Answer: C · Worked explanation

In an adiabatic change Q=0Q=0Q=0, so ΔU=−W\Delta U=-WΔU=−W. Compression means the gas does negative work, so ΔU\Delta UΔU is positive and the temperature rises. Zero heat transfer does not mean unchanged internal energy, because work still changes it. Constant temperature describes an isothermal change.
10.

Hard·Compare[2 marks]

Which statement correctly compares the idealised Otto and diesel cycles?
Show answer and explanation

Answer: B · Worked explanation

The spark in a petrol engine ignites a compressed fuel–air mixture, giving heating at constant volume. In a diesel engine only air is compressed and fuel burns as it is injected, giving heating at constant pressure. Reversing these steps, or giving the diesel cycle a spark, describes neither engine.

Keep going

Next topic3.12.1 Discovery of the electronPrevious topic3.11.1 Rotational dynamics

More in Section 3.11 · Option: Engineering physics

  1. 3.11.1Rotational dynamicsNotes · 10 questions
  2. 3.11.2Thermodynamics and enginesNotes · 10 questions

All AQA A-level Physics topics →

Draft: written by Scribe and checked automatically, not yet by a subject reviewer.

Practice questions are original, written by Scribe and checked automatically for correctness.

Topic codes follow the official numbering. Not endorsed by AQA or any exam board.

On this page

0/6 read

  1. 1Heat and work both change the internal energy of a gas
  2. 2The first law says energy is conserved in these transfers
  3. 3On a pV diagram the area represents work done
  4. 4A heat engine turns some heat input into useful work
  5. 5The temperatures of hot and cold reservoirs limit efficiency
  6. 6Petrol and diesel engines differ in how they add heat
  7. Check your recall
  8. Practice: 10 questions
All coursesScribeHow it worksPricingPrivacyTerms

Notes and questions are written by Scribe in our own words. Topic codes follow the official course numbering so you can find your place. Not produced or endorsed by the IB, College Board, AQA, OCR, Pearson Edexcel or any exam board.

© 2026 Scribe