Scribe logoScribeNotes & practice
Sign inStart free
  1. Notes
  2. ›IB Physics
  3. ›B The particulate nature of matter
  4. ›B.5 Current and circuits

IB Physics · Theme B · The particulate nature of matter

B.5 Current and circuits

Explain current and potential difference, apply Ohm’s law, calculate resistance, and interpret simple circuit diagrams.

  • 5 min read
  • 6 parts
  • 10 questions
  • Draft
Start a Quick 5 on this topic→Jump to the 10 questions
1/6Electric current measures the rate of charge flow
  1. 1Electric current measures the rate of charge flow
  2. 2Potential difference tracks energy transferred by each charge
  3. 3Resistance depends on the conductor and controls power transfer
  4. 4Series and parallel connections combine resistances differently
  5. 5Circuit diagrams show connections and measurement positions
  6. 6Junction and loop rules explain potential dividers
  7. Check your recall
  8. Practice: 10 questions
1

Part 1 of 6: Electric current measures the rate of charge flow

An electric current is the rate at which charge passes a point. If charge QQQ passes in time ttt, the current is I=QtI=\frac{Q}{t}I=tQ​. Current is measured in amperes (A), charge in coulombs (C), and time in seconds (s). A current of 1 A means 1 C passes each second. Conventional current points in the direction positive charge would move. Electrons move in the opposite direction through a metal wire.

Common mistake

Current is not used up as it passes through a resistor. Charge continues around a complete circuit.

Key terms · tap one for its definition

electric current

Electric current is the rate of flow of charge past a point.

conventional current

Conventional current has the direction in which positive charge would flow.

Part 1 done

2

Part 2 of 6: Potential difference tracks energy transferred by each charge

A cell gives energy to charges moving around a circuit. Potential difference is the energy transferred per unit charge between two points: V=EQV=\frac{E}{Q}V=QE​. It is measured in volts (V), where 1 V means 1 J per coulomb. Current tells us how quickly charge flows. Potential difference tells us how much energy each unit of charge transfers.

A cell’s electromotive force is the energy it supplies per unit charge. Some energy transfers inside the cell when current flows. This happens because the cell has internal resistance, rrr. If the external resistance is RRR, then E=I(R+r)\mathcal{E}=I(R+r)E=I(R+r). The terminal potential difference is V=IR=E−IrV=IR=\mathcal{E}-IrV=IR=E−Ir, where IrIrIr is the voltage across the internal resistance.

Key terms · tap one for its definition

potential difference

The energy transferred per unit charge between two points, measured in volts.

electromotive force

The energy supplied by a source per unit charge, measured in volts.

internal resistance

Resistance within a source that reduces its terminal potential difference by IrIrIr when current III flows.

Part 2 done

Quick check

One question on the part you just read

Easy

Identify the quantity that describes how much charge passes a point each second.
Show answer and explanation

Answer: C · Worked explanation

Electric current is the rate of flow of charge past a point, so it describes charge passing each second. Potential difference instead describes energy transferred per unit charge. Resistance describes how strongly a component opposes current, while energy is a quantity that can be transferred.
3

Part 3 of 6: Resistance depends on the conductor and controls power transfer

A longer wire offers charges more resistance. A thicker wire offers less. Its resistivity, ρ\rhoρ, describes the material’s effect on resistance. For a uniform wire, R=ρLAR=\frac{\rho L}{A}R=AρL​, where LLL is length and AAA is cross-sectional area. Resistivity has units of Ω m\Omega\,\mathrm{m}Ωm and changes with temperature.

Resistance at an operating point is R=VIR=\frac{V}{I}R=IV​. Ohm’s law says current is proportional to potential difference when physical conditions remain constant. An ohmic resistor therefore has constant resistance and obeys V=IRV=IRV=IR. A filament lamp is not ohmic because its temperature changes as current rises.

A resistor transfers electrical energy to its surroundings. Electrical power is energy transferred each second. Calculate it using P=IVP=IVP=IV. For a resistor, substituting V=IRV=IRV=IR also gives P=I2R=V2RP=I^2R=\frac{V^2}{R}P=I2R=RV2​. Power is measured in watts (W).

Exam tip

State that temperature remains constant when applying Ohm’s law. The equation V=IRV=IRV=IR can still describe a non-ohmic component at one operating point.

Key terms · tap one for its definition

resistance

Resistance is the ratio of potential difference across a component to current through it.

Ohm’s law

Ohm’s law states that current is proportional to potential difference when physical conditions remain constant.

resistivity

A material property equal to RA/LRA/LRA/L for a uniform conductor, measured in Ω m\Omega\,\mathrm{m}Ωm.

electrical power

The rate of electrical energy transfer, measured in watts, where 1 W=1 J s−11\,\mathrm{W}=1\,\mathrm{J\,s^{-1}}1W=1Js−1.

Part 3 done

4

Part 4 of 6: Series and parallel connections combine resistances differently

In series, components share one path. The same current passes through each resistor, while their potential differences add. Their total resistance is Rtotal=R1+R2+⋯R_{\mathrm{total}}=R_1+R_2+\cdotsRtotal​=R1​+R2​+⋯. In parallel, components connect across the same two points. Each branch has the same potential difference, while the branch currents add. Their combined resistance satisfies 1Rtotal=1R1+1R2+⋯\frac{1}{R_{\mathrm{total}}}=\frac{1}{R_1}+\frac{1}{R_2}+\cdotsRtotal​1​=R1​1​+R2​1​+⋯.

Adding a series resistor increases total resistance. Adding a parallel branch provides another path, so total resistance decreases. For positive resistances, the parallel total is smaller than either individual resistance.

Worked example

Finding total resistance and current

A 6 Ω resistor and a 3 Ω resistor are connected in parallel. This combination is in series with a 2 Ω resistor across a 12 V supply. Find the total resistance and supply current.
  1. 1
    For the parallel pair, 1Rparallel=16+13=12 Ω−1\frac{1}{R_{\mathrm{parallel}}}=\frac{1}{6}+\frac{1}{3}=\frac{1}{2}\,\Omega^{-1}Rparallel​1​=61​+31​=21​Ω−1.
  2. 2
    Therefore, Rparallel=2 ΩR_{\mathrm{parallel}}=2\,\OmegaRparallel​=2Ω.
  3. 3
    Add the series resistance: Rtotal=2+2=4 ΩR_{\mathrm{total}}=2+2=4\,\OmegaRtotal​=2+2=4Ω.
  4. 4
    Use I=VRtotal=124=3 AI=\frac{V}{R_{\mathrm{total}}}=\frac{12}{4}=3\,\mathrm{A}I=Rtotal​V​=412​=3A.

Answer: The total resistance is 4 Ω, and the supply current is 3 A.

Key terms · tap one for its definition

series

Components in series lie on one path and carry the same current.

parallel

Components in parallel connect across the same two points and share a potential difference.

Part 4 done

Quick check

One question on the part you just read

Easy

State the direction of conventional current in a metal wire relative to the direction in which its electrons move.
Show answer and explanation

Answer: A · Worked explanation

Conventional current is defined as the direction in which positive charge would move. In a metal wire, electrons move in the opposite direction, so conventional current and electron motion are opposite. The idea that they travel in the same direction confuses electron flow with the conventional-current convention.
5

Part 5 of 6: Circuit diagrams show connections and measurement positions

A circuit diagram uses symbols and connecting lines to show electrical connections. A cell symbol has one long and one short line. A resistor is shown as a rectangle, and a closed switch completes a path. Trace each path to decide whether components are in series or parallel. Their positions on the page matter less than which points they connect.

An ammeter measures current and goes in series with the component. A voltmeter measures potential difference and goes in parallel across it. When interpreting readings, identify the measured component before applying an equation. An ideal ammeter has zero resistance; an ideal voltmeter has infinite resistance. These assumptions prevent the meters from changing the circuit.

Figure 1. The ammeter lies on the main path. The voltmeter connects across the resistor.

Common mistake

A crossing of wires is not necessarily a junction. A junction must show that the paths are electrically connected.

Key terms · tap one for its definition

circuit diagram

A circuit diagram uses standard symbols and lines to show how electrical components connect.

ammeter

An ammeter measures current and is connected in series.

voltmeter

A voltmeter measures potential difference and is connected in parallel.

Part 5 done

6

Part 6 of 6: Junction and loop rules explain potential dividers

Now that circuit diagrams show each connection, follow charge through a junction. Kirchhoff’s laws express two conservation rules. Currents entering a junction add to the currents leaving it. Around any closed loop, the sum of potential rises equals the sum of potential drops. These rules also explain why series voltages add and parallel branches share a potential difference.

A potential divider uses two resistors in series to provide part of a supply voltage. The same current passes through both, so voltage divides in proportion to resistance. For an ideal supply VinV_{\mathrm{in}}Vin​, the voltage across R2R_2R2​ is Vout=VinR2R1+R2V_{\mathrm{out}}=V_{\mathrm{in}}\frac{R_2}{R_1+R_2}Vout​=Vin​R1​+R2​R2​​. This result assumes nothing connected across R2R_2R2​ draws current. A connected load can change the output voltage.

Key terms · tap one for its definition

Kirchhoff’s laws

The junction rule conserves charge; the closed-loop rule conserves energy per unit charge.

potential divider

A series-resistor arrangement that provides an output potential difference across part of the circuit.

Note read

Check your recall[14 marks]

6 written questions. Answer each one in your head or on paper, then open the mark scheme.

  1. 1.Define[2 marks]

    Define electric current and state its unit.

    Show mark schemeHide mark scheme

    Model answer

    Electric current is charge passing a point per unit time. Its unit is the ampere.

    • 1 mark for defining current as the rate of charge flow
    • 1 mark for stating the ampere as its unit
  2. 2.Explain[2 marks]

    Explain how potential difference differs from current.

    Show mark schemeHide mark scheme

    Model answer

    Potential difference is energy transferred per unit charge. Current is charge flowing per unit time.

    • 1 mark for identifying potential difference as energy transferred per unit charge
    • 1 mark for identifying current as charge flowing per unit time
  3. 3.Calculate[2 marks]

    Calculate the current through a 4 Ω ohmic resistor connected across 12 V.

    Show mark schemeHide mark scheme

    Model answer

    Using I=VRI=\frac{V}{R}I=RV​, I=124=3 AI=\frac{12}{4}=3\,\mathrm{A}I=412​=3A.

    • 1 mark for using I=VRI=\frac{V}{R}I=RV​ with the given values
    • 1 mark for obtaining 3 A
  4. 4.Calculate[3 marks]

    Calculate the total resistance of 6 Ω and 3 Ω resistors in parallel.

    Show mark schemeHide mark scheme

    Model answer

    1Rtotal=16+13=12 Ω−1\frac{1}{R_{\mathrm{total}}}=\frac{1}{6}+\frac{1}{3}=\frac{1}{2}\,\Omega^{-1}Rtotal​1​=61​+31​=21​Ω−1, so Rtotal=2 ΩR_{\mathrm{total}}=2\,\OmegaRtotal​=2Ω.

    • 1 mark for using the reciprocal rule for parallel resistance
    • 1 mark for calculating the reciprocal total as 12 Ω−1\frac{1}{2}\,\Omega^{-1}21​Ω−1
    • 1 mark for obtaining a total resistance of 2 Ω
  5. 5.Describe[2 marks]

    Describe where to connect an ammeter and voltmeter when measuring a resistor.

    Show mark schemeHide mark scheme

    Model answer

    Connect the ammeter in series with the resistor. Connect the voltmeter in parallel across the resistor.

    • 1 mark for placing the ammeter in series with the resistor
    • 1 mark for placing the voltmeter in parallel across the resistor
  6. 6.Explain[3 marks]

    Explain how current and potential difference behave across two parallel resistors.

    Show mark schemeHide mark scheme

    Model answer

    Both resistors connect across the same two points, so each has the same potential difference. Current divides between the branches. The branch currents add to give the total current.

    • 1 mark for stating that both branches have the same potential difference
    • 1 mark for stating that current divides between branches
    • 1 mark for stating that branch currents add to give the total current

Practice this topic

10 quick-fire multiple-choice questions, easy to hard. Tap an answer to see if you're right and the worked explanation. (The written questions with mark schemes are under “Check your recall” above.)

0 right0 of 10 answered

Includes the 2 quick checks in the note above.

3.

Easy·Identify[1 mark]

Which quantity describes the energy transferred for each coulomb of charge moving between two points?
Show answer and explanation

Answer: A · Worked explanation

Potential difference is the energy transferred per unit charge between two points, measured in volts. Current describes how quickly charge flows, not the energy transferred by each coulomb. Resistance and charge are also different quantities: neither is defined as energy per unit charge.
4.

Easy·State[1 mark]

For an ohmic resistor, state the condition required for current to be proportional to potential difference.
Show answer and explanation

Answer: A · Worked explanation

Ohm’s law states that current is proportional to potential difference when physical conditions, especially temperature, remain constant. A particular connection arrangement or a potential difference of exactly 1 V is not required. If temperature changes, a resistor’s resistance may change and the proportional relationship may no longer hold.
5.

Easy·Identify[1 mark]

Identify the circuit component represented by one long line and one short line in a circuit diagram.
Show answer and explanation

Answer: D · Worked explanation

A cell is represented by a pair of parallel lines of unequal length: one long and one short. A resistor is shown as a rectangle, while a switch has a break or contact representation. The ammeter is represented by its meter symbol, not by unequal parallel lines.
6.

Medium·Calculate[2 marks]

A charge of 15 C passes a point in a wire in 5.0 s. Calculate the current in the wire.
Show answer and explanation

Answer: B · Worked explanation

Use the rate of charge flow, I=Q/tI=Q/tI=Q/t. Substituting gives I=15/5.0=3.0I=15/5.0=3.0I=15/5.0=3.0 A. The tempting value 0.33 A comes from reversing the division; current is charge divided by time, not time divided by charge.
7.

Medium·Calculate[2 marks]

A component has a potential difference of 9.0 V across it and a current of 0.30 A through it. Calculate its resistance at this operating point.
Show answer and explanation

Answer: C · Worked explanation

Use R=V/IR=V/IR=V/I: R=9.0/0.30=30R=9.0/0.30=30R=9.0/0.30=30 Ω. This is the resistance at the stated operating point, whether or not the component is ohmic. The tempting value 2.7 Ω comes from multiplying voltage by current rather than dividing.
8.

Medium·Calculate[2 marks]

Two resistors of 4.0 Ω and 7.0 Ω are connected in series. Calculate their total resistance.
Show answer and explanation

Answer: B · Worked explanation

For resistors in series, total resistance is the sum: Rtotal=4.0+7.0=11R_{\mathrm{total}}=4.0+7.0=11Rtotal​=4.0+7.0=11 Ω. The tempting value 2.5 Ω is an incorrect reciprocal-style combination; the reciprocal rule applies to parallel resistors, not series resistors.
9.

Medium·Determine[2 marks]

Resistors of 8.0 Ω and 8.0 Ω are connected in parallel. Determine their combined resistance.
Show answer and explanation

Answer: A · Worked explanation

For two equal resistors in parallel, the reciprocal rule gives 1/Rtotal=1/8.0+1/8.0=1/4.01/R_{\mathrm{total}}=1/8.0+1/8.0=1/4.01/Rtotal​=1/8.0+1/8.0=1/4.0, so Rtotal=4.0R_{\mathrm{total}}=4.0Rtotal​=4.0 Ω. The tempting 16 Ω is the sum used for a series connection; adding a parallel path lowers the combined resistance.
10.

Medium·Determine[2 marks]

A circuit has a cell and a resistor on one complete path. A meter is inserted into the path so that all the circuit current passes through it. A second meter is connected between the two ends of the resistor. Identify the correct meter arrangement.
Show answer and explanation

Answer: D · Worked explanation

An ammeter measures current and is connected in series so that the circuit current passes through it. A voltmeter measures potential difference and is connected in parallel across the component. The tempting reversed arrangement would place a voltmeter in series and an ammeter across the resistor, contrary to their measurement connections.

Keep going

Next topicC.1 Simple harmonic motionPrevious topicB.4 Thermodynamics

More in Theme B · The particulate nature of matter

  1. B.1Thermal energy transfersNotes · 10 questions
  2. B.2Greenhouse effectNotes · 10 questions
  3. B.3Gas lawsNotes · 10 questions
  4. B.4ThermodynamicsNotes · 10 questions· HL only
  5. B.5Current and circuitsNotes · 10 questions

All IB Physics topics →

Draft: written by Scribe and checked automatically, not yet by a subject reviewer.

Practice questions are original, written by Scribe and checked automatically for correctness.

Topic codes follow the official numbering. Not endorsed by IB Diploma Programme or any exam board.

On this page

0/6 read

  1. 1Electric current measures the rate of charge flow
  2. 2Potential difference tracks energy transferred by each charge
  3. 3Resistance depends on the conductor and controls power transfer
  4. 4Series and parallel connections combine resistances differently
  5. 5Circuit diagrams show connections and measurement positions
  6. 6Junction and loop rules explain potential dividers
  7. Check your recall
  8. Practice: 10 questions
All coursesScribeHow it worksPricingPrivacyTerms

Notes and questions are written by Scribe in our own words. Topic codes follow the official course numbering so you can find your place. Not produced or endorsed by the IB, College Board, AQA, OCR, Pearson Edexcel or any exam board.

© 2026 Scribe