Scribe logoScribeNotes & practice
Sign inStart free
  1. Notes
  2. ›AP Environmental Science
  3. ›6 Energy Resources and Consumption
  4. ›6.10 Geothermal energy

AP Environmental Science · Unit 6 · Energy Resources and Consumption

6.10 Geothermal energy

Explain how geothermal energy is produced and used, identify where it is available, and list its advantages and disadvantages.

  • 4 min read
  • 6 parts
  • 10 questions
  • Draft
Start a Quick 5 on this topic→Jump to the 10 questions
1/6The Earth’s interior supplies a steady flow of heat
  1. 1The Earth’s interior supplies a steady flow of heat
  2. 2Hot water and steam from underground can drive turbines
  3. 3Geothermal heat can also be used directly for warmth
  4. 4Geothermal resources cluster near plate boundaries and hot spots
  5. 5Geothermal power is steady, low in emissions and compact
  6. 6Cost, location and local side effects limit geothermal power
  7. Check your recall
  8. Practice: 10 questions
1

Part 1 of 6: The Earth’s interior supplies a steady flow of heat

Dig a deep mine and the rock gets hotter as you go down. Temperature rises with depth, a pattern called the geothermal gradient. Some of this heat is left over from the planet’s formation, and some comes from radioactive decay in rock.

Heat from within the Earth that people can use is called geothermal energy. It can be used directly or converted to electricity. The heat flow is continuous on human time scales, so geothermal energy is considered renewable.

The heat is not equally easy to reach everywhere. In most places, the rock near the surface is far too cool to generate power.

Key terms · tap one for its definition

geothermal gradient

The geothermal gradient is the rate at which temperature rises with depth below Earth’s surface.

geothermal energy

Geothermal energy is thermal energy stored in rock and fluids beneath Earth’s surface, produced mainly by radioactive decay and residual heat.

Part 1 done

2

Part 2 of 6: Hot water and steam from underground can drive turbines

Now consider how that heat becomes electricity. In many places, groundwater seeps into hot rock and warms up. The hot water or steam collects in porous rock.

  • Workers drill a production well into the hot zone.
  • Hot water or steam rises up the well to the surface.
  • The steam spins a turbine connected to a generator.
  • Cooled water is pumped back down an injection well.
Figure 1. Hot fluid rises to the plant, and cooled water goes back down so the underground supply lasts.

Returning the water keeps the underground supply topped up. Plant designs differ. Very hot reservoirs give steam directly, while cooler ones heat a second fluid that boils at a lower temperature.

Key terms · tap one for its definition

turbine

A turbine is a rotating machine whose blades are turned by a moving fluid, such as water, steam or wind.

generator

A generator is a machine that converts the motion of a rotating shaft into electrical energy.

Part 2 done

Quick check

One question on the part you just read

Easy

Identify the main sources of the heat used in geothermal energy.
Show answer and explanation

Answer: A · Worked explanation

The Earth’s interior is heated by radioactive decay in rock and by heat left over from the planet’s formation. Sunlight warms only the thin surface layer, so it does not supply geothermal energy. Wind friction adds almost no heat. Nothing is burning underground to heat the rock.
3

Part 3 of 6: Geothermal heat can also be used directly for warmth

Not every use needs a turbine. Where underground water is hot enough, pipes can carry it straight to buildings, greenhouses and fish farms. This direct use skips electricity generation.

Ground a few meters below the surface stays near a steady temperature all year. A geothermal heat pump moves heat between a building and the ground using buried pipes. It warms the building in winter and cools it in summer.

Common mistake

A geothermal heat pump does not tap deep volcanic heat. It uses the steady temperature of shallow ground, so it works almost anywhere.

Key terms · tap one for its definition

direct use

Direct use is the piping of geothermal hot water or steam to supply heat without first converting it to electricity.

geothermal heat pump

A geothermal heat pump is a system of buried pipes and a pump that transfers heat between the ground and a building.

Part 3 done

4

Part 4 of 6: Geothermal resources cluster near plate boundaries and hot spots

Power plants need very hot rock close to the surface, so location matters. Earth’s outer layer is split into large slabs, each one a tectonic plate. Where plates meet, magma rises near the surface and heats rock and groundwater above it.

Volcanoes, geysers and hot springs often mark such places. Many strong resources lie around the Pacific Ocean, in a belt of volcanoes and earthquakes called the Ring of Fire. Iceland sits on a plate boundary and uses geothermal energy widely for heating and electricity.

A few sites lie over a hot spot, away from plate edges. In the United States, the best resources are mainly in the western states.

Key terms · tap one for its definition

tectonic plate

A tectonic plate is a large slab of Earth’s rigid outer layer that moves slowly relative to neighboring slabs.

hot spot

A hot spot is a location where unusually hot rock rises from deep within Earth and heats the crust above it.

Part 4 done

Quick check

One question on the part you just read

Easy

Identify the location most likely to have strong geothermal resources.
Show answer and explanation

Answer: C · Worked explanation

Where plates meet, magma rises close to the surface and heats the rock and groundwater above it, so volcanic regions on plate boundaries have strong resources. Sunshine does not create geothermal heat. Stable plate interiors are far from such heat, and a cold climate is irrelevant to what lies deep underground.
5

Part 5 of 6: Geothermal power is steady, low in emissions and compact

Geothermal strengths follow from a heat source that never switches off.

  • It runs day and night in any weather, giving baseload power.
  • Operation releases few greenhouse gases compared with burning fossil fuels.
  • A plant uses little land for the electricity it makes.
  • Fuel costs are near zero once the wells are drilled.

Returning water to the ground helps keep a field productive for decades. Because the heat is always there, output does not depend on the weather or on the time of day.

Key term

baseload

Baseload power is electricity supplied at a steady rate that meets the minimum demand on a grid around the clock.

Part 5 done

6

Part 6 of 6: Cost, location and local side effects limit geothermal power

Those strengths apply only where a site exists, and building one is hard. Costs and side effects add to the challenge.

  • Good sites are limited to certain regions.
  • Drilling is costly, and some wells find too little heat.
  • Underground fluids can release hydrogen sulfide and other gases.
  • Injecting water can trigger small earthquakes.
  • Pumping out water faster than rain and groundwater replace it can cool the field.

Common mistake

Geothermal energy is not unlimited at a single site. A field can lose heat if it is managed poorly.

Key term

hydrogen sulfide

Hydrogen sulfide, H2S\mathrm{H_2S}H2​S, is a gas with a rotten-egg smell that is harmful at high concentrations.

Note read

Check your recall[12 marks]

5 written questions. Answer each one in your head or on paper, then open the mark scheme.

  1. 1.Describe[3 marks]

    Describe how a geothermal power plant uses underground heat to produce electricity.

    Show mark schemeHide mark scheme

    Model answer

    A production well brings hot water or steam to the surface. The steam spins a turbine that drives a generator. Cooled water is returned underground through an injection well.

    • 1 mark for stating that a production well brings hot water or steam to the surface
    • 1 mark for stating that the steam spins a turbine connected to a generator
    • 1 mark for stating that cooled water is returned through an injection well
  2. 2.Identify[2 marks]

    Identify two kinds of location where geothermal resources are most available.

    Show mark schemeHide mark scheme

    Model answer

    Any two of: near tectonic plate boundaries, over hot spots, in volcanic regions such as around the Ring of Fire.

    • 1 mark for identifying one correct kind of location
    • 1 mark for identifying a second correct kind of location
  3. 3.Explain[2 marks]

    Explain why a geothermal heat pump can be installed where there are no hot springs or volcanoes.

    Show mark schemeHide mark scheme

    Model answer

    Ground a few meters down stays at a steady temperature all year. The heat pump moves heat between the building and the ground, so it does not need hot rock.

    • 1 mark for stating that shallow ground stays near a steady temperature
    • 1 mark for explaining that the pump moves heat between the ground and a building, so hot rock is not required
  4. 4.Justify[3 marks]

    Justify why geothermal power is described as reliable but not suitable everywhere.

    Show mark schemeHide mark scheme

    Model answer

    The Earth’s heat is continuous, so a plant gives baseload power in any weather. However, power plants need very hot rock near the surface. Few regions have such sites, and drilling is costly.

    • 1 mark for stating that the heat source is continuous, giving baseload power
    • 1 mark for stating that power plants need very hot rock near the surface
    • 1 mark for stating that suitable sites are limited or that drilling is costly
  5. 5.Describe[2 marks]

    Describe two environmental disadvantages of geothermal energy.

    Show mark schemeHide mark scheme

    Model answer

    Underground fluids can release gases such as hydrogen sulfide. Injecting water can trigger small earthquakes.

    • 1 mark for describing one correct disadvantage
    • 1 mark for describing a second correct disadvantage

Practice this topic

10 quick-fire multiple-choice questions, easy to hard. Tap an answer to see if you're right and the worked explanation. (The written questions with mark schemes are under “Check your recall” above.)

0 right0 of 10 answered

Includes the 2 quick checks in the note above.

3.

Easy·Identify[1 mark]

Identify a use of geothermal energy that does not involve making electricity.
Show answer and explanation

Answer: B · Worked explanation

Direct use sends geothermal hot water straight to buildings, greenhouses or fish farms as heat, with no electricity generation. Spinning a turbine, driving a generator and supplying current to homes are all steps in making electricity. They describe a geothermal power plant, which is a different use of the same heat.
4.

Medium·Explain[1 mark]

A geothermal plant returns cooled water to the ground through an injection well. Explain the main benefit.
Show answer and explanation

Answer: A · Worked explanation

Returning cooled water keeps the underground supply topped up, which helps the field produce heat for decades. Water removed faster than it is replaced can cool a field. Injection does not remove the need for a turbine, which the steam still spins. It also cannot guarantee that no gases escape.
5.

Medium·Calculate[1 mark]

A geothermal plant produces 50 MW continuously for 24 hours. Calculate the energy it produces.
Show answer and explanation

Answer: D · Worked explanation

Energy equals power times time, so 50 MW × 24 h = 1200 MWh. The value 2.1 MWh comes from dividing power by time instead of multiplying. The value 74 MWh comes from adding the two numbers. The value 120 MWh results from a decimal slip in the multiplication.
6.

Medium·Identify[1 mark]

A family lives in a region with no volcanoes or hot springs and wants low-emission heating. Identify the most suitable geothermal option.
Show answer and explanation

Answer: B · Worked explanation

A heat pump needs only the steady temperature of shallow ground, which exists almost everywhere. Direct use needs hot water to be nearby, and power plants need very hot rock near the surface, so both fail without volcanic or hot spring resources. Drilling to molten rock is neither practical nor how geothermal systems are built.
7.

Medium·Identify[1 mark]

Identify the pairing that correctly matches a geothermal disadvantage with its cause.
Show answer and explanation

Answer: C · Worked explanation

A field can lose heat when water is removed faster than rain and groundwater restore it. The rotten-egg smell comes from hydrogen sulfide in underground fluids, not from burning fuel. Small earthquakes can be triggered by injecting fluid. Upfront cost comes from expensive drilling, since geothermal fuel costs are near zero.
8.

Hard·Identify[2 marks]

A town needs electricity around the clock. Identify the statement that best supports a geothermal plant for this need.
Show answer and explanation

Answer: D · Worked explanation

Because Earth’s heat flow is continuous, a geothermal plant supplies baseload power day and night. Geothermal plants need suitable underground heat, so they cannot be built anywhere. Drilling makes upfront costs high. Underground fluids can release gases such as hydrogen sulfide, so the claim of no gases is incorrect.
9.

Hard·Justify[2 marks]

A student claims geothermal energy is renewable and cannot run low at any site. Justify the most accurate response.
Show answer and explanation

Answer: A · Worked explanation

Earth’s heat supply is continuous, which is why geothermal energy is considered renewable. A single field, however, can cool locally if fluid is pumped out faster than natural recharge, so poor management can deplete it. No fuel is burned to make the heat, and geothermal output does not stop at night.
10.

Hard·Determine[2 marks]

A geothermal plant and a solar farm each have a 100 MW capacity. In one day, the geothermal plant runs at full output for 24 hours. The solar farm runs at full output for 6 hours in total. Determine how many more MWh the geothermal plant supplies.
Show answer and explanation

Answer: B · Worked explanation

Geothermal energy is 100 MW × 24 h = 2400 MWh. Solar energy is 100 MW × 6 h = 600 MWh. The difference is 2400 − 600 = 1800 MWh. The value 2,400 MWh is only the geothermal total, 600 MWh is only the solar total, and 3,000 MWh comes from adding the two totals instead of subtracting.

Keep going

Next topic6.11 Hydrogen fuel cellsPrevious topic6.9 Hydroelectric power

More in Unit 6 · Energy Resources and Consumption

  1. 6.5Fossil fuelsNotes · 10 questions
  2. 6.6Nuclear powerNotes · 10 questions
  3. 6.7Energy from biomassNotes · 10 questions
  4. 6.8Solar energyNotes · 10 questions
  5. 6.9Hydroelectric powerNotes · 10 questions
  6. 6.10Geothermal energyNotes · 10 questions
  7. 6.11Hydrogen fuel cellsNotes · 10 questions
  8. 6.12Wind energyNotes · 10 questions
  9. 6.13Energy conservationNotes · 10 questions

All AP Environmental Science topics →

Draft: written by Scribe and checked automatically, not yet by a subject reviewer.

Practice questions are original, written by Scribe and checked automatically for correctness.

Topic codes follow the official numbering. Not endorsed by College Board or any exam board.

On this page

0/6 read

  1. 1The Earth’s interior supplies a steady flow of heat
  2. 2Hot water and steam from underground can drive turbines
  3. 3Geothermal heat can also be used directly for warmth
  4. 4Geothermal resources cluster near plate boundaries and hot spots
  5. 5Geothermal power is steady, low in emissions and compact
  6. 6Cost, location and local side effects limit geothermal power
  7. Check your recall
  8. Practice: 10 questions
All coursesScribeHow it worksPricingPrivacyTerms

Notes and questions are written by Scribe in our own words. Topic codes follow the official course numbering so you can find your place. Not produced or endorsed by the IB, College Board, AQA, OCR, Pearson Edexcel or any exam board.

© 2026 Scribe