Scribe logoScribeNotes & practice
Sign inStart free
  1. Notes
  2. ›AP Physics 2
  3. ›11 Electric Circuits
  4. ›11.3 Resistance, resistivity and Ohm's law

AP Physics 2 · Unit 11 · Electric Circuits

11.3 Resistance, resistivity and Ohm's law

Explain Ohm’s law, calculate resistance, current, or potential difference, and describe how resistivity, length, and area determine a wire’s resistance.

  • 4 min read
  • 5 parts
  • 10 questions
  • Draft
Start a Quick 5 on this topic→Jump to the 10 questions
1/5Resistance measures how strongly an object opposes current
  1. 1Resistance measures how strongly an object opposes current
  2. 2Ohm’s law links potential difference, current, and resistance
  3. 3Resistivity is a property of the material itself
  4. 4Longer wires resist more and thicker wires resist less
  5. 5Not every conductor obeys Ohm’s law under all conditions
  6. Check your recall
  7. Practice: 10 questions
1

Part 1 of 5: Resistance measures how strongly an object opposes current

Think of water flowing through a narrow pipe and then a wide one. The narrow pipe opposes the flow more. A conductor treats charge in a similar way.

An electric potential difference pushes charge through a conductor. How much current results depends on the conductor’s resistance, RRR. Resistance is the ratio of potential difference to current, R=ΔVIR=\frac{\Delta V}{I}R=IΔV​.

Its unit is the ohm, written Ω\OmegaΩ, where 1 Ω=1 V/A1\,\Omega=1\,\mathrm{V/A}1Ω=1V/A. A larger resistance means less current for the same potential difference. Resistance belongs to the object itself, not to the circuit it sits in.

Key terms · tap one for its definition

electric potential difference

The electric potential difference ΔV\Delta VΔV is the change in electric potential energy per unit charge, ΔUE/q\Delta U_E/qΔUE​/q, measured in volts, where 1 V=1 J/C1\,\mathrm{V}=1\,\mathrm{J/C}1V=1J/C.

resistance

The resistance RRR of a conductor is the ratio of the potential difference across it to the current through it, measured in ohms, where 1 Ω=1 V/A1\,\Omega=1\,\mathrm{V/A}1Ω=1V/A.

Part 1 done

2

Part 2 of 5: Ohm’s law links potential difference, current, and resistance

Now rearrange that definition to predict current. For many conductors at constant temperature, the resistance stays the same as the potential difference changes. This behavior is Ohm’s law, written ΔV=IR\Delta V=IRΔV=IR. Such a conductor is called ohmic.

Doubling ΔV\Delta VΔV across an ohmic resistor doubles the current. A graph of ΔV\Delta VΔV against III is a straight line through the origin, and its slope is RRR. Rearranged forms are I=ΔVRI=\frac{\Delta V}{R}I=RΔV​ and R=ΔVIR=\frac{\Delta V}{I}R=IΔV​.

Figure 1. Each line is straight and passes through the origin, so the resistance is constant. The steeper line belongs to the larger resistance.

Worked example

Resistance and current

A resistor connected to a 9.0 V9.0\,\mathrm{V}9.0V battery carries 0.30 A0.30\,\mathrm{A}0.30A. Calculate its resistance. Then calculate the current when the potential difference is raised to 12 V12\,\mathrm{V}12V.
  1. 1
    Resistance equals potential difference divided by current: R=ΔVI=9.0 V0.30 A=30 ΩR=\frac{\Delta V}{I}=\frac{9.0\,\mathrm{V}}{0.30\,\mathrm{A}}=30\,\OmegaR=IΔV​=0.30A9.0V​=30Ω.
  2. 2
    The resistor is ohmic, so RRR stays at 30 Ω30\,\Omega30Ω.
  3. 3
    Current equals potential difference divided by resistance: I=ΔVR=12 V30 Ω=0.40 AI=\frac{\Delta V}{R}=\frac{12\,\mathrm{V}}{30\,\Omega}=0.40\,\mathrm{A}I=RΔV​=30Ω12V​=0.40A.

Answer: The resistance is 30 Ω30\,\Omega30Ω, and the current at 12 V12\,\mathrm{V}12V is 0.40 A0.40\,\mathrm{A}0.40A.

Common mistake

The potential difference and current do not set the resistance. The material, length, area, and temperature do. For an ohmic conductor, changing the potential difference changes only the current.

Key terms · tap one for its definition

Ohm’s law

Ohm’s law states that the current through an ohmic conductor is proportional to the potential difference across it, ΔV=IR\Delta V=IRΔV=IR, at constant temperature.

ohmic

An ohmic conductor is one whose resistance stays constant as the potential difference across it changes.

Part 2 done

Quick check

One question on the part you just read

Easy

Identify the unit of resistance.
Show answer and explanation

Answer: C · Worked explanation

Resistance is potential difference divided by current, so its unit is volts per ampere, which is the ohm. The ampere is the unit of current, and the volt is the unit of potential difference. The watt measures energy transferred per second, not resistance.
3

Part 3 of 5: Resistivity is a property of the material itself

Two wires of the same shape but different metals can have different resistances. Resistivity explains why.

The resistivity ρ\rhoρ of a material describes how strongly the material resists current, independent of the object’s shape. It is measured in ohm-meters, Ω m\Omega\,\mathrm{m}Ωm.

For a uniform wire of length ℓ\ellℓ and cross-sectional area AAA, the resistance is R=ρℓAR=\frac{\rho\ell}{A}R=Aρℓ​. The cross-sectional area is the area of the wire’s end face.

Exam tip

The upright A\mathrm{A}A means amperes, while the italic AAA means area. Keep the units beside each value so they never get mixed up.

Key terms · tap one for its definition

resistivity

The resistivity ρ\rhoρ of a material is the property that, with a conductor’s length and cross-sectional area, sets its resistance, measured in Ω m\Omega\,\mathrm{m}Ωm.

cross-sectional area

The cross-sectional area AAA of a wire is the area of a slice cut perpendicular to its length, measured in m2\mathrm{m^2}m2.

Part 3 done

4

Part 4 of 5: Longer wires resist more and thicker wires resist less

Apply the formula to see how shape changes resistance. Compare a long, thin pipe with a short, wide one. Charge moves most easily through the short, wide one.

  • Doubling the length doubles the resistance.
  • Doubling the cross-sectional area halves the resistance.
  • Doubling the radius makes the area four times larger, so the resistance falls to one quarter.
  • Changing the material changes ρ\rhoρ, and so changes RRR.

Use ratios to reason quickly. Write each change as a factor, then multiply the factors together.

Worked example

Resistance of a wire

A wire has resistivity 4.0×10−7 Ω m4.0\times10^{-7}\,\Omega\,\mathrm{m}4.0×10−7Ωm, length 1.5 m1.5\,\mathrm{m}1.5m, and cross-sectional area 2.0×10−7 m22.0\times10^{-7}\,\mathrm{m^2}2.0×10−7m2. Calculate its resistance.
  1. 1
    Resistance depends on resistivity, length, and area: R=ρℓAR=\frac{\rho\ell}{A}R=Aρℓ​.
  2. 2
    Substitute: R=(4.0×10−7 Ω m)(1.5 m)2.0×10−7 m2R=\frac{(4.0\times10^{-7}\,\Omega\,\mathrm{m})(1.5\,\mathrm{m})}{2.0\times10^{-7}\,\mathrm{m^2}}R=2.0×10−7m2(4.0×10−7Ωm)(1.5m)​.
  3. 3
    Evaluate: R=3.0 ΩR=3.0\,\OmegaR=3.0Ω.

Answer: The resistance is 3.0 Ω3.0\,\Omega3.0Ω.

Part 4 done

Quick check

One question on the part you just read

Easy

Identify the correct form of Ohm’s law.
Show answer and explanation

Answer: C · Worked explanation

Ohm’s law states that potential difference equals current times resistance. Checking units confirms it: amperes times ohms gives volts. Writing ΔV=I/R\Delta V=I/RΔV=I/R gives amperes per ohm, which is not a unit of potential difference. Rearranging gives I=ΔVRI=\frac{\Delta V}{R}I=RΔV​ as well, but the product form is the standard statement.
5

Part 5 of 5: Not every conductor obeys Ohm’s law under all conditions

The straight-line graph holds only while resistance stays constant. A lamp filament gets very hot as current rises. In a metal, higher temperature raises resistivity, so the resistance increases, and the graph of ΔV\Delta VΔV against III curves upward.

Such a device is non-ohmic. Its resistance at any one point is still the ratio of potential difference to current there. Only the proportionality fails.

A resistor also links back to energy. Charge passing through it loses electric potential energy, and the energy becomes thermal energy.

Exam tip

To test whether a device is ohmic, check that ΔVI\frac{\Delta V}{I}IΔV​ stays the same at several different currents.

Key term

non-ohmic

A non-ohmic conductor is one whose resistance changes as the potential difference across it changes.

Note read

Check your recall[13 marks]

6 written questions. Answer each one in your head or on paper, then open the mark scheme.

  1. 1.Explain[2 marks]

    Explain why doubling the potential difference across an ohmic resistor doubles the current.

    Show mark schemeHide mark scheme

    Model answer

    An ohmic resistor has constant resistance. Since I=ΔVRI=\frac{\Delta V}{R}I=RΔV​, the current is proportional to the potential difference, so doubling ΔV\Delta VΔV doubles III.

    • 1 mark for stating that the resistance of an ohmic resistor is constant
    • 1 mark for using I=ΔV/RI=\Delta V/RI=ΔV/R to show that current is proportional to potential difference
  2. 2.Calculate[2 marks]

    Calculate the potential difference across a 25 Ω25\,\Omega25Ω resistor that carries 0.40 A0.40\,\mathrm{A}0.40A.

    Show mark schemeHide mark scheme

    Model answer

    ΔV=IR=(0.40 A)(25 Ω)=10 V\Delta V=IR=(0.40\,\mathrm{A})(25\,\Omega)=10\,\mathrm{V}ΔV=IR=(0.40A)(25Ω)=10V.

    • 1 mark for using ΔV=IR\Delta V=IRΔV=IR with correct substitution
    • 1 mark for obtaining 10 V10\,\mathrm{V}10V
  3. 3.Determine[3 marks]

    A wire has resistivity 5.0×10−7 Ω m5.0\times10^{-7}\,\Omega\,\mathrm{m}5.0×10−7Ωm, length 2.4 m2.4\,\mathrm{m}2.4m, and cross-sectional area 3.0×10−7 m23.0\times10^{-7}\,\mathrm{m^2}3.0×10−7m2. Determine its resistance.

    Show mark schemeHide mark scheme

    Model answer

    R=ρℓA=(5.0×10−7 Ω m)(2.4 m)3.0×10−7 m2=4.0 ΩR=\frac{\rho\ell}{A}=\frac{(5.0\times10^{-7}\,\Omega\,\mathrm{m})(2.4\,\mathrm{m})}{3.0\times10^{-7}\,\mathrm{m^2}}=4.0\,\OmegaR=Aρℓ​=3.0×10−7m2(5.0×10−7Ωm)(2.4m)​=4.0Ω.

    • 1 mark for using R=ρℓ/AR=\rho\ell/AR=ρℓ/A
    • 1 mark for substituting the given values correctly
    • 1 mark for obtaining 4.0 Ω4.0\,\Omega4.0Ω
  4. 4.Predict[2 marks]

    Predict how the resistance changes when a wire is replaced by one of the same material and length but twice the diameter. Give a reason.

    Show mark schemeHide mark scheme

    Model answer

    The resistance falls to one quarter. Doubling the diameter makes the cross-sectional area four times larger, and resistance is inversely proportional to area.

    • 1 mark for predicting that the resistance becomes one quarter of its original value
    • 1 mark for reasoning that the area becomes four times larger and resistance varies inversely with area
  5. 5.Describe[2 marks]

    Describe the graph of ΔV\Delta VΔV against III for an ohmic resistor, and state what its slope represents.

    Show mark schemeHide mark scheme

    Model answer

    The graph is a straight line through the origin. Its slope equals the resistance.

    • 1 mark for describing a straight line through the origin
    • 1 mark for stating that the slope is the resistance
  6. 6.Explain[2 marks]

    Explain why the graph of potential difference against current for a lamp filament curves upward.

    Show mark schemeHide mark scheme

    Model answer

    As the current rises, the filament gets hotter. The higher temperature raises its resistivity and resistance, so each extra ampere needs a larger increase in potential difference.

    • 1 mark for stating that the filament’s temperature rises as the current rises
    • 1 mark for explaining that its resistance increases, so the ratio of potential difference to current increases

Practice this topic

10 quick-fire multiple-choice questions, easy to hard. Tap an answer to see if you're right and the worked explanation. (The written questions with mark schemes are under “Check your recall” above.)

0 right0 of 10 answered

Includes the 2 quick checks in the note above.

3.

Easy·Identify[1 mark]

Identify the factor, other than temperature, that sets a material’s resistivity.
Show answer and explanation

Answer: D · Worked explanation

Resistivity is a property of the material itself, independent of the shape of the object. Length and area affect the resistance of a particular wire, but they do not change the resistivity. The current does not set resistivity either. Changing a wire’s dimensions changes its resistance, but the same material keeps the same resistivity.
4.

Medium·Calculate[2 marks]

A conductor carries 0.60 A0.60\,\mathrm{A}0.60A when 18 V18\,\mathrm{V}18V is across it. Calculate its resistance.
Show answer and explanation

Answer: C · Worked explanation

R=ΔVI=18 V0.60 A=30 ΩR=\frac{\Delta V}{I}=\frac{18\,\mathrm{V}}{0.60\,\mathrm{A}}=30\,\OmegaR=IΔV​=0.60A18V​=30Ω. The value of 0.033 Ω0.033\,\Omega0.033Ω comes from dividing current by potential difference, which inverts the ratio. The value of 11 Ω11\,\Omega11Ω multiplies the two quantities together. As a check, 30 Ω×0.60 A=18 V30\,\Omega\times0.60\,\mathrm{A}=18\,\mathrm{V}30Ω×0.60A=18V. The value of 17 Ω17\,\Omega17Ω subtracts the current from the potential difference.
5.

Medium·Calculate[2 marks]

A 240 Ω240\,\Omega240Ω resistor has 120 V120\,\mathrm{V}120V across it. Calculate the current through it.
Show answer and explanation

Answer: A · Worked explanation

I=ΔVR=120 V240 Ω=0.50 AI=\frac{\Delta V}{R}=\frac{120\,\mathrm{V}}{240\,\Omega}=0.50\,\mathrm{A}I=RΔV​=240Ω120V​=0.50A. The value of 2.0 A2.0\,\mathrm{A}2.0A comes from dividing the resistance by the potential difference. The value of 2.9×104 A2.9\times10^{4}\,\mathrm{A}2.9×104A multiplies the two quantities. As a check, 0.50 A×240 Ω=120 V0.50\,\mathrm{A}\times240\,\Omega=120\,\mathrm{V}0.50A×240Ω=120V. The value of 360 A360\,\mathrm{A}360A adds the two numbers, which is not a physical relationship.
6.

Medium·Predict[2 marks]

A wire has its length doubled and its cross-sectional area doubled. The material stays the same. Predict how its resistance changes.
Show answer and explanation

Answer: B · Worked explanation

Resistance is R=ρℓAR=\frac{\rho\ell}{A}R=Aρℓ​. Doubling the length doubles RRR, and doubling the area halves it, so the two changes cancel. Doubling alone would apply only if the area stayed fixed, and halving would apply only if the length stayed fixed. Using ratios avoids needing actual values for the material.
7.

Medium·Calculate[2 marks]

A wire has resistivity 1.2×10−6 Ω m1.2\times10^{-6}\,\Omega\,\mathrm{m}1.2×10−6Ωm, length 0.50 m0.50\,\mathrm{m}0.50m, and cross-sectional area 3.0×10−7 m23.0\times10^{-7}\,\mathrm{m^2}3.0×10−7m2. Calculate its resistance.
Show answer and explanation

Answer: B · Worked explanation

R=ρℓA=(1.2×10−6 Ω m)(0.50 m)3.0×10−7 m2=2.0 ΩR=\frac{\rho\ell}{A}=\frac{(1.2\times10^{-6}\,\Omega\,\mathrm{m})(0.50\,\mathrm{m})}{3.0\times10^{-7}\,\mathrm{m^2}}=2.0\,\OmegaR=Aρℓ​=3.0×10−7m2(1.2×10−6Ωm)(0.50m)​=2.0Ω. The value of 8.0 Ω8.0\,\Omega8.0Ω divides the resistivity by the product of length and area. The value of 0.50 Ω0.50\,\Omega0.50Ω inverts the correct answer. Cancel the units to check: Ω m\Omega\,\mathrm{m}Ωm times m\mathrm{m}m divided by m2\mathrm{m^2}m2 leaves ohms. The value of 0.20 Ω0.20\,\Omega0.20Ω is off by a factor of ten, a slip in the powers of ten.
8.

Hard·Predict[2 marks]

Two wires are made of the same material and have the same length. Wire B has three times the diameter of wire A. Predict the ratio of the resistance of B to that of A.
Show answer and explanation

Answer: C · Worked explanation

Area varies with the square of the diameter, so wire B has nine times the area. Resistance varies inversely with area, so RB/RA=19R_B/R_A=\frac{1}{9}RB​/RA​=91​. A ratio of 13\frac{1}{3}31​ treats area as proportional to diameter instead of to diameter squared. As a check, if wire A has an area of 1 unit, wire B has 9 units, so B resists one ninth as much.
9.

Hard·Determine[2 marks]

Wire X has length L and radius r. Wire Y is made of the same material, with length 2L and radius 2r. Determine the ratio of the resistance of Y to that of X.
Show answer and explanation

Answer: A · Worked explanation

Doubling the length doubles the resistance. Doubling the radius makes the area four times larger, which divides the resistance by four. Together, RY/RX=24=12R_Y/R_X=\frac{2}{4}=\frac{1}{2}RY​/RX​=42​=21​. A ratio of 2 counts only the length change and ignores the larger area. As a check, use ℓ=1\ell=1ℓ=1 and r=1r=1r=1 for X, so R∝11R\propto\frac{1}{1}R∝11​, and R∝24R\propto\frac{2}{4}R∝42​ for Y.
10.

Hard·Justify[2 marks]

A lamp carries 0.40 A0.40\,\mathrm{A}0.40A with 2.0 V2.0\,\mathrm{V}2.0V across it. It carries 0.80 A0.80\,\mathrm{A}0.80A with 6.0 V6.0\,\mathrm{V}6.0V across it. Which conclusion is justified by these data?
Show answer and explanation

Answer: B · Worked explanation

At the first reading, R=2.00.40=5.0 ΩR=\frac{2.0}{0.40}=5.0\,\OmegaR=0.402.0​=5.0Ω. At the second, R=6.00.80=7.5 ΩR=\frac{6.0}{0.80}=7.5\,\OmegaR=0.806.0​=7.5Ω. A changing resistance means the lamp is non-ohmic. Current rising with potential difference alone does not show an ohmic conductor, because the current must rise in proportion. Both ratios must be computed, since the reading at a single point cannot show whether resistance changes.

Keep going

Next topic11.4 Electric powerPrevious topic11.2 Simple circuits

More in Unit 11 · Electric Circuits

  1. 11.1Electric currentNotes · 10 questions
  2. 11.2Simple circuitsNotes · 10 questions
  3. 11.3Resistance, resistivity and Ohm's lawNotes · 10 questions
  4. 11.4Electric powerNotes · 10 questions
  5. 11.5Compound DC circuitsNotes · 10 questions
  6. 11.6Kirchhoff's loop ruleNotes · 10 questions
  7. 11.7Kirchhoff's junction ruleNotes · 10 questions
  8. 11.8RC circuitsNotes · 10 questions

All AP Physics 2 topics →

Draft: written by Scribe and checked automatically, not yet by a subject reviewer.

Practice questions are original, written by Scribe and checked automatically for correctness.

Topic codes follow the official numbering. Not endorsed by College Board or any exam board.

On this page

0/5 read

  1. 1Resistance measures how strongly an object opposes current
  2. 2Ohm’s law links potential difference, current, and resistance
  3. 3Resistivity is a property of the material itself
  4. 4Longer wires resist more and thicker wires resist less
  5. 5Not every conductor obeys Ohm’s law under all conditions
  6. Check your recall
  7. Practice: 10 questions
All coursesScribeHow it worksPricingPrivacyTerms

Notes and questions are written by Scribe in our own words. Topic codes follow the official course numbering so you can find your place. Not produced or endorsed by the IB, College Board, AQA, OCR, Pearson Edexcel or any exam board.

© 2026 Scribe

Potential difference against current for two ohmic resistors

Potential difference ΔV (V)00.511.5205101520Current I (A)
  • 5.0 Ω resistor
  • 10 Ω resistor