Scribe logoScribeNotes & practice
Sign inStart free
  1. Notes
  2. ›AP Physics 2
  3. ›11 Electric Circuits
  4. ›11.7 Kirchhoff's junction rule

AP Physics 2 · Unit 11 · Electric Circuits

11.7 Kirchhoff's junction rule

Apply Kirchhoff’s junction rule to find unknown currents, and explain how it follows from conservation of charge.

  • 4 min read
  • 5 parts
  • 10 questions
  • Draft
Start a Quick 5 on this topic→Jump to the 10 questions
1/5Charge arriving at a junction must also leave
  1. 1Charge arriving at a junction must also leave
  2. 2Balancing currents finds an unknown current at a junction
  3. 3A branch carries its own current between two junctions
  4. 4Junction and loop equations together solve a multi-branch circuit
  5. 5The junction rule follows from conservation of charge
  6. Check your recall
  7. Practice: 10 questions
1

Part 1 of 5: Charge arriving at a junction must also leave

Picture a water pipe that splits into two smaller pipes. Every liter that enters the split also leaves through one of the branches. Nothing collects at the fork.

Wires in a circuit work the same way. Current arriving where wires meet must divide among the wires that leave.

A junction is a point where three or more wires meet. Kirchhoff’s junction rule says the total current entering a junction equals the total current leaving it: ∑Iin=∑Iout\sum I_\mathrm{in}=\sum I_\mathrm{out}∑Iin​=∑Iout​.

Current is the rate at which charge passes a point. The rule is therefore really a statement about charge.

Key terms · tap one for its definition

junction

A junction is a point in a circuit where three or more conductors meet, so the current can divide or combine.

Kirchhoff’s junction rule

Kirchhoff’s junction rule states that the sum of the currents entering a junction equals the sum of the currents leaving it.

Part 1 done

2

Part 2 of 5: Balancing currents finds an unknown current at a junction

Now use the rule on numbers. List every wire at the junction and mark each as entering or leaving. Add the entering currents, add the leaving currents, and set the two sums equal. Treat each current as positive in the direction you chose. Then the same equation holds at every junction.

Worked example

Current in the fourth wire

A junction joins four wires. Currents of 5.0 A and 2.0 A enter the junction, and 3.0 A leaves in one wire. Determine the current in the fourth wire, which also leaves.
  1. 1
    Entering total: 5.0 A+2.0 A=7.0 A5.0\,\mathrm{A}+2.0\,\mathrm{A}=7.0\,\mathrm{A}5.0A+2.0A=7.0A.
  2. 2
    Write the rule: ∑Iin=∑Iout\sum I_\mathrm{in}=\sum I_\mathrm{out}∑Iin​=∑Iout​, so 7.0 A=3.0 A+I47.0\,\mathrm{A}=3.0\,\mathrm{A}+I_47.0A=3.0A+I4​.
  3. 3
    Solve: I4=7.0 A−3.0 A=4.0 AI_4=7.0\,\mathrm{A}-3.0\,\mathrm{A}=4.0\,\mathrm{A}I4​=7.0A−3.0A=4.0A.

Answer: The fourth wire carries 4.0 A away from the junction.

Common mistake

A resistor does not use up current. The same current leaves a resistor as enters it, because the resistor transfers energy, not charge.

If you guess a direction wrongly, the algebra returns a negative value. That current simply flows the opposite way.

Part 2 done

Quick check

One question on the part you just read

Easy

Identify what Kirchhoff’s junction rule says is equal to the total current entering a junction.
Show answer and explanation

Answer: B · Worked explanation

The junction rule says the sum of the currents entering a junction equals the sum of the currents leaving it. Potential differences belong to the loop rule. The current in the battery is only one of the currents that may meet at a junction, and resistance does not appear in the rule.
3

Part 3 of 5: A branch carries its own current between two junctions

A circuit with parallel paths has several junctions. A branch is a path between two junctions that carries one current. A battery and a resistor in the same wire share a single branch current. In the figure, the battery wire and two resistor branches meet at junctions a and b.

Figure 1. Current I₁ enters junction a and divides into I₂ and I₃. The two branches rejoin at junction b.

At junction a, I1I_1I1​ enters while I2I_2I2​ and I3I_3I3​ leave. The rule gives I1=I2+I3I_1=I_2+I_3I1​=I2​+I3​. At junction b the same three currents return, and the rule gives the same equation.

Two junctions therefore supply only one independent equation here.

Key term

branch

A branch is a path between two junctions that carries a single current along its whole length.

Part 3 done

4

Part 4 of 5: Junction and loop equations together solve a multi-branch circuit

Pick directions for I1I_1I1​, I2I_2I2​ and I3I_3I3​ as shown. Unknown currents need as many independent equations as unknowns. The junction rule gives relationships between currents. The loop rule gives energy relationships. Together they solve the circuit in the figure. A loop around the outside of the figure adds no new information.

Worked example

Three unknown branch currents

In the figure, a 12 V battery drives current through R1=2.0 ΩR_1=2.0\,\OmegaR1​=2.0Ω, then through branches with R2=3.0 ΩR_2=3.0\,\OmegaR2​=3.0Ω and R3=6.0 ΩR_3=6.0\,\OmegaR3​=6.0Ω. Determine I1I_1I1​, I2I_2I2​ and I3I_3I3​.
  1. 1
    Junction a: I1=I2+I3I_1=I_2+I_3I1​=I2​+I3​.
  2. 2
    Loop through the battery, R1R_1R1​ and R2R_2R2​: +12−2.0I1−3.0I2=0+12-2.0I_1-3.0I_2=0+12−2.0I1​−3.0I2​=0, with values in volts, ohms and amperes.
  3. 3
    Loop through R2R_2R2​ and R3R_3R3​, going down R2R_2R2​ and up R3R_3R3​: −3.0I2+6.0I3=0-3.0I_2+6.0I_3=0−3.0I2​+6.0I3​=0, so I2=2I3I_2=2I_3I2​=2I3​.
  4. 4
    Then I1=3I3I_1=3I_3I1​=3I3​. Substituting gives 12−6.0I3−6.0I3=012-6.0I_3-6.0I_3=012−6.0I3​−6.0I3​=0, so I3=1.0 AI_3=1.0\,\mathrm{A}I3​=1.0A.

Answer: I1=3.0 AI_1=3.0\,\mathrm{A}I1​=3.0A, I2=2.0 AI_2=2.0\,\mathrm{A}I2​=2.0A and I3=1.0 AI_3=1.0\,\mathrm{A}I3​=1.0A.

The loop through R2R_2R2​ and R3R_3R3​ has no battery. The loop rule still applies to it.

Exam tip

Count your unknowns before you start. Write exactly that many independent equations, then solve them together.

Part 4 done

Quick check

One question on the part you just read

Easy

Identify the conservation law on which the junction rule is based.
Show answer and explanation

Answer: C · Worked explanation

Charge cannot be created, destroyed or stored at a junction in a steady circuit, so charge arriving each second equals charge leaving each second. Conservation of energy underlies the loop rule instead. Momentum and mass play no role in the rule, which is about the flow of charge.
5

Part 5 of 5: The junction rule follows from conservation of charge

Charge cannot be created or destroyed, so it cannot vanish at a junction. In a steady circuit it does not pile up there either. Whatever arrives must leave.

Suppose more charge arrived than left. The junction would become charged, and its electric field would quickly oppose any further imbalance. Real circuits settle almost at once, so the currents in and out balance.

The loop rule reflects conservation of energy, and the junction rule reflects conservation of charge. Together they let you analyze most DC circuits. Each rule rests on one idea, so both work for circuits of any size.

Note read

Check your recall[12 marks]

5 written questions. Answer each one in your head or on paper, then open the mark scheme.

  1. 1.Describe[2 marks]

    Describe Kirchhoff’s junction rule for the currents at a junction.

    Show mark schemeHide mark scheme

    Model answer

    The total current entering a junction equals the total current leaving it, ∑Iin=∑Iout\sum I_\mathrm{in}=\sum I_\mathrm{out}∑Iin​=∑Iout​.

    • 1 mark for comparing the currents entering and leaving a junction
    • 1 mark for stating that the totals are equal
  2. 2.Determine[2 marks]

    Determine the current that leaves a junction through a single wire when 4.0 A and 1.5 A enter through two other wires and 2.0 A leaves through a third wire. The single wire also leaves.

    Show mark schemeHide mark scheme

    Model answer

    Entering total =4.0 A+1.5 A=5.5 A=4.0\,\mathrm{A}+1.5\,\mathrm{A}=5.5\,\mathrm{A}=4.0A+1.5A=5.5A. Leaving: 5.5 A=2.0 A+I5.5\,\mathrm{A}=2.0\,\mathrm{A}+I5.5A=2.0A+I, so I=3.5 AI=3.5\,\mathrm{A}I=3.5A.

    • 1 mark for equating the entering and leaving totals
    • 1 mark for obtaining 3.5 A3.5\,\mathrm{A}3.5A
  3. 3.Explain[2 marks]

    Explain how the junction rule reflects conservation of charge.

    Show mark schemeHide mark scheme

    Model answer

    Charge cannot be created, destroyed or accumulated at a junction in a steady circuit. Charge arriving each second must therefore equal charge leaving each second, so the currents balance.

    • 1 mark for stating that charge is conserved and does not accumulate at the junction
    • 1 mark for linking equal charge per second in and out to equal currents
  4. 4.Determine[4 marks]

    Determine the current in each parallel resistor, using the junction rule and the loop rule. A 12 V battery is connected to a 2.0 Ω2.0\,\Omega2.0Ω resistor in series with two parallel 4.0 Ω4.0\,\Omega4.0Ω resistors.

    Show mark schemeHide mark scheme

    Model answer

    The junction rule gives I1=I2+I3I_1=I_2+I_3I1​=I2​+I3​, and symmetry from the loop through the two parallel resistors gives I2=I3I_2=I_3I2​=I3​, so I1=2I2I_1=2I_2I1​=2I2​. The battery loop gives 12−2.0I1−4.0I2=012-2.0I_1-4.0I_2=012−2.0I1​−4.0I2​=0, so 12−8.0I2=012-8.0I_2=012−8.0I2​=0 and I2=1.5 AI_2=1.5\,\mathrm{A}I2​=1.5A. Each parallel resistor carries 1.5 A1.5\,\mathrm{A}1.5A.

    • 1 mark for writing the junction equation I1=I2+I3I_1=I_2+I_3I1​=I2​+I3​
    • 1 mark for showing I2=I3I_2=I_3I2​=I3​ from a loop through the two parallel resistors
    • 1 mark for writing the loop equation through the battery
    • 1 mark for obtaining 1.5 A1.5\,\mathrm{A}1.5A in each parallel resistor
  5. 5.Predict[2 marks]

    Predict what would happen at a junction if, for a short time, more charge arrived each second than left.

    Show mark schemeHide mark scheme

    Model answer

    Charge would accumulate at the junction, making it charged. The resulting electric field would oppose further imbalance, so the currents would quickly balance.

    • 1 mark for stating that charge would accumulate at the junction
    • 1 mark for stating that the resulting field would restore balance

Practice this topic

10 quick-fire multiple-choice questions, easy to hard. Tap an answer to see if you're right and the worked explanation. (The written questions with mark schemes are under “Check your recall” above.)

0 right0 of 10 answered

Includes the 2 quick checks in the note above.

3.

Easy·Determine[1 mark]

Currents of 3.0 A3.0\,\mathrm{A}3.0A and 2.0 A2.0\,\mathrm{A}2.0A enter a junction through two wires. One other wire carries current away from the junction. Determine the current in that wire.
Show answer and explanation

Answer: B · Worked explanation

The entering total is 3.0 A+2.0 A=5.0 A3.0\,\mathrm{A}+2.0\,\mathrm{A}=5.0\,\mathrm{A}3.0A+2.0A=5.0A. The single leaving wire must carry all of it, 5.0 A5.0\,\mathrm{A}5.0A. The value 1.0 A1.0\,\mathrm{A}1.0A subtracts the currents, and 6.0 A6.0\,\mathrm{A}6.0A multiplies them. The value 2.5 A2.5\,\mathrm{A}2.5A averages them, which has no basis in the rule. The leaving wire is the only exit, so it must carry the entire entering total.
4.

Medium·Determine[2 marks]

A wire carries 6.0 A6.0\,\mathrm{A}6.0A into a junction. A second wire carries 2.5 A2.5\,\mathrm{A}2.5A away from it. A third wire also carries current away. Determine the current in the third wire.
Show answer and explanation

Answer: C · Worked explanation

The entering current is 6.0 A6.0\,\mathrm{A}6.0A, so 6.0 A=2.5 A+I6.0\,\mathrm{A}=2.5\,\mathrm{A}+I6.0A=2.5A+I and I=3.5 AI=3.5\,\mathrm{A}I=3.5A. The value 8.5 A8.5\,\mathrm{A}8.5A adds the two known currents even though one enters and one leaves. The value 2.4 A2.4\,\mathrm{A}2.4A divides the currents, which has no basis in the rule. Entering and leaving currents must be counted separately before they are compared.
5.

Medium[2 marks]

A junction has wires carrying 1.5 A and 0.50 A into it and 3.0 A away from it. A fourth wire is also attached. Which statement must be true?
Show answer and explanation

Answer: C · Worked explanation

The entering total of 2.0 A is less than the leaving 3.0 A, so another 1.0 A must enter through the fourth wire. If the fourth wire carried 1.0 A away, 4.0 A would leave while only 2.0 A enters. The value 5.0 A adds all three currents without regard to direction.
6.

Medium·Determine[2 marks]

A current of 3.0 A3.0\,\mathrm{A}3.0A splits at a junction into two branches. One branch carries 1.2 A1.2\,\mathrm{A}1.2A. Determine the current in the other branch.
Show answer and explanation

Answer: D · Worked explanation

The branch currents add to the entering current, so I=3.0 A−1.2 A=1.8 AI=3.0\,\mathrm{A}-1.2\,\mathrm{A}=1.8\,\mathrm{A}I=3.0A−1.2A=1.8A. The value 4.2 A4.2\,\mathrm{A}4.2A adds the currents, as if both entered. The value 2.5 A2.5\,\mathrm{A}2.5A divides them, and 3.6 A3.6\,\mathrm{A}3.6A multiplies them. The rule involves only sums and differences. Check that the two branch currents add back to the original 3.0 A.
7.

Medium[2 marks]

A student claims that the current leaving a bulb is smaller than the current entering it, because the bulb uses up current. Which response is correct?
Show answer and explanation

Answer: C · Worked explanation

Charge flows through the bulb without being lost, so the same current leaves as enters. The bulb transfers electrical energy to thermal energy and light. A potential difference across the bulb does not reduce the current in the wire. The currents are equal whatever the bulb’s resistance.
8.

Hard·Determine[2 marks]

An 18 V18\,\mathrm{V}18V battery is connected to a 2.0 Ω2.0\,\Omega2.0Ω resistor in series with a parallel pair of 12 Ω12\,\Omega12Ω and 6.0 Ω6.0\,\Omega6.0Ω resistors. Determine the current in the 12 Ω12\,\Omega12Ω resistor.
Show answer and explanation

Answer: D · Worked explanation

The pair has 112+16=14\frac{1}{12}+\frac{1}{6}=\frac{1}{4}121​+61​=41​, so 4.0 Ω4.0\,\Omega4.0Ω. Then Req=6.0 ΩR_\mathrm{eq}=6.0\,\OmegaReq​=6.0Ω and the source current is 3.0 A3.0\,\mathrm{A}3.0A. The 2.0 Ω2.0\,\Omega2.0Ω resistor drops 6.0 V6.0\,\mathrm{V}6.0V, leaving 12 V12\,\mathrm{V}12V across the pair, so I=12 V12 Ω=1.0 AI=\frac{12\,\mathrm{V}}{12\,\Omega}=1.0\,\mathrm{A}I=12Ω12V​=1.0A. The value 1.5 A1.5\,\mathrm{A}1.5A wrongly splits the current equally. As a check, the branch currents 1.0 A1.0\,\mathrm{A}1.0A and 2.0 A2.0\,\mathrm{A}2.0A add to the source current.
9.

Hard[2 marks]

A circuit has three branches joining the same two junctions. Each branch current is unknown. How many independent equations does the junction rule supply for these two junctions?
Show answer and explanation

Answer: A · Worked explanation

At the first junction the branch currents obey I1=I2+I3I_1=I_2+I_3I1​=I2​+I3​. At the second junction the same three currents appear with entering and leaving reversed, which gives the identical equation. The two junctions therefore supply one independent equation. The remaining equations must come from loops.
10.

Hard·Determine[2 marks]

A current of 4.0 A4.0\,\mathrm{A}4.0A enters a junction and divides between two parallel branches of 6.0 Ω6.0\,\Omega6.0Ω and 12 Ω12\,\Omega12Ω. Determine the current in the 6.0 Ω6.0\,\Omega6.0Ω branch.
Show answer and explanation

Answer: C · Worked explanation

The pair has R=4.0 ΩR=4.0\,\OmegaR=4.0Ω, so the shared potential difference is (4.0 A)(4.0 Ω)=16 V(4.0\,\mathrm{A})(4.0\,\Omega)=16\,\mathrm{V}(4.0A)(4.0Ω)=16V. Then I=16 V6.0 Ω=2.7 AI=\frac{16\,\mathrm{V}}{6.0\,\Omega}=2.7\,\mathrm{A}I=6.0Ω16V​=2.7A. The value 1.3 A1.3\,\mathrm{A}1.3A is the current in the 12 Ω12\,\Omega12Ω branch. The value 2.0 A2.0\,\mathrm{A}2.0A wrongly assumes an equal split. As a check, 2.7 A+1.3 A=4.0 A2.7\,\mathrm{A}+1.3\,\mathrm{A}=4.0\,\mathrm{A}2.7A+1.3A=4.0A, as the junction rule requires.

Keep going

Next topic11.8 RC circuitsPrevious topic11.6 Kirchhoff's loop rule

More in Unit 11 · Electric Circuits

  1. 11.1Electric currentNotes · 10 questions
  2. 11.2Simple circuitsNotes · 10 questions
  3. 11.3Resistance, resistivity and Ohm's lawNotes · 10 questions
  4. 11.4Electric powerNotes · 10 questions
  5. 11.5Compound DC circuitsNotes · 10 questions
  6. 11.6Kirchhoff's loop ruleNotes · 10 questions
  7. 11.7Kirchhoff's junction ruleNotes · 10 questions
  8. 11.8RC circuitsNotes · 10 questions

All AP Physics 2 topics →

Draft: written by Scribe and checked automatically, not yet by a subject reviewer.

Practice questions are original, written by Scribe and checked automatically for correctness.

Topic codes follow the official numbering. Not endorsed by College Board or any exam board.

On this page

0/5 read

  1. 1Charge arriving at a junction must also leave
  2. 2Balancing currents finds an unknown current at a junction
  3. 3A branch carries its own current between two junctions
  4. 4Junction and loop equations together solve a multi-branch circuit
  5. 5The junction rule follows from conservation of charge
  6. Check your recall
  7. Practice: 10 questions
All coursesScribeHow it worksPricingPrivacyTerms

Notes and questions are written by Scribe in our own words. Topic codes follow the official course numbering so you can find your place. Not produced or endorsed by the IB, College Board, AQA, OCR, Pearson Edexcel or any exam board.

© 2026 Scribe