Scribe logoScribeNotes & practice
Sign inStart free
  1. Notes
  2. ›AP Physics 2
  3. ›11 Electric Circuits
  4. ›11.6 Kirchhoff's loop rule

AP Physics 2 · Unit 11 · Electric Circuits

11.6 Kirchhoff's loop rule

Apply Kirchhoff’s loop rule to write energy equations for a circuit loop and solve for unknown currents or potential differences.

  • 4 min read
  • 5 parts
  • 10 questions
  • Draft
Start a Quick 5 on this topic→Jump to the 10 questions
1/5Potential differences around a closed loop add to zero
  1. 1Potential differences around a closed loop add to zero
  2. 2Each circuit element adds a signed term to the equation
  3. 3A single loop gives one equation for one unknown current
  4. 4Every independent loop in a larger circuit gives an equation
  5. 5Use the loop rule when a circuit cannot be reduced
  6. Check your recall
  7. Practice: 10 questions
1

Part 1 of 5: Potential differences around a closed loop add to zero

Imagine walking a hiking trail that returns to its start. Every climb is canceled by a descent, so your net change in height is zero. Charge moving around a circuit behaves the same way with electric potential.

A closed loop is any path through a circuit that returns to its starting point. Kirchhoff’s loop rule says the potential differences around a closed loop sum to zero: ∑ΔV=0\sum \Delta V=0∑ΔV=0.

The rule expresses conservation of energy. Energy is gained in batteries and lost in resistors. A charge that returns to its starting point has the same electric potential energy as before. The gains and losses therefore balance.

Key terms · tap one for its definition

closed loop

A closed loop is a path through a circuit that returns to its starting point without crossing any element twice.

Kirchhoff’s loop rule

Kirchhoff’s loop rule states that the sum of the potential differences around any closed loop is zero, ∑ΔV=0\sum \Delta V=0∑ΔV=0.

Part 1 done

2

Part 2 of 5: Each circuit element adds a signed term to the equation

To use the rule, choose a loop and a direction of travel. Then go element by element and record each potential difference with its sign. The result is a loop equation.

Sign of each term when traveling around a loop

ElementDirection of travelTerm
Batteryfrom − terminal to + terminal+ΔVbattery+\Delta V_\mathrm{battery}+ΔVbattery​
Batteryfrom + terminal to − terminal−ΔVbattery-\Delta V_\mathrm{battery}−ΔVbattery​
Resistorsame direction as the current−IR-IR−IR
Resistoropposite to the current+IR+IR+IR
Element
Battery
Direction of travel
from − terminal to + terminal
Term
+ΔVbattery+\Delta V_\mathrm{battery}+ΔVbattery​
Element
Battery
Direction of travel
from + terminal to − terminal
Term
−ΔVbattery-\Delta V_\mathrm{battery}−ΔVbattery​
Element
Resistor
Direction of travel
same direction as the current
Term
−IR-IR−IR
Element
Resistor
Direction of travel
opposite to the current
Term
+IR+IR+IR

A resistor lowers the potential along the current, so that term is negative. Travel against the current, and the term flips sign. A battery works the other way. Crossing it from the negative to the positive terminal raises the potential.

Exam tip

Pick a current direction at the start and keep it. If the final current is negative, it flows opposite to your choice.

Key term

loop equation

A loop equation is the loop rule written for one loop, with each element’s potential difference entered with its sign.

Part 2 done

Quick check

One question on the part you just read

Easy

Identify the conservation law on which Kirchhoff’s loop rule is based.
Show answer and explanation

Answer: B · Worked explanation

A charge that returns to its starting point has no net change in electric potential energy. That is conservation of energy. Conservation of charge underlies the junction rule for currents, not the loop rule. Momentum and mass play no role in the potential differences around a loop.
3

Part 3 of 5: A single loop gives one equation for one unknown current

Now apply the rule to a real circuit. Two batteries sit in one loop with two resistors. The 12 V battery pushes charge clockwise, and the 6.0 V battery pushes it counterclockwise. The larger battery wins, so the current is clockwise.

Figure 1. The long plate of each battery is the positive terminal. Traveling clockwise crosses the 12 V battery upward and the 6.0 V battery downward.

Worked example

Two opposing batteries in one loop

In the circuit shown, a 12 V battery and a 6.0 V battery oppose each other in one loop with resistors of 3.0 Ω3.0\,\Omega3.0Ω and 1.0 Ω1.0\,\Omega1.0Ω. Determine the current.
  1. 1
    Travel clockwise, the direction of the current.
  2. 2
    Write the loop equation: +12 V−I(3.0 Ω)−6.0 V−I(1.0 Ω)=0+12\,\mathrm{V}-I(3.0\,\Omega)-6.0\,\mathrm{V}-I(1.0\,\Omega)=0+12V−I(3.0Ω)−6.0V−I(1.0Ω)=0.
  3. 3
    Combine terms: 6.0 V−I(4.0 Ω)=06.0\,\mathrm{V}-I(4.0\,\Omega)=06.0V−I(4.0Ω)=0.
  4. 4
    Solve: I=6.0 V4.0 Ω=1.5 AI=\frac{6.0\,\mathrm{V}}{4.0\,\Omega}=1.5\,\mathrm{A}I=4.0Ω6.0V​=1.5A.

Answer: The current is 1.5 A, clockwise.

Check the result against the batteries. The resistors drop 4.5 V and 1.5 V. Together these equal the net 6.0 V supplied by the two batteries, so the loop rule is satisfied.

Part 3 done

4

Part 4 of 5: Every independent loop in a larger circuit gives an equation

Larger circuits contain several loops. To solve for nnn unknown currents you need nnn independent equations. A loop adds a new equation only if it is an independent loop. The junction rule for currents supplies the remaining equations.

The loop rule also explains a fact about parallel branches. Take resistors R2R_2R2​ and R3R_3R3​ joined at the same two points. Going down one and up the other gives −I2R2+I3R3=0-I_2R_2+I_3R_3=0−I2​R2​+I3​R3​=0.

So I2R2=I3R3I_2R_2=I_3R_3I2​R2​=I3​R3​, and the two potential differences are equal. This loop contains no battery, yet the rule still holds.

Key term

independent loop

An independent loop is a loop that includes at least one element not already included in the loops chosen.

Part 4 done

Quick check

One question on the part you just read

Easy

According to the loop rule, the sum of the potential differences around any closed loop is what?
Show answer and explanation

Answer: D · Worked explanation

The loop rule states that the potential differences around a closed loop sum to zero, because the potential must return to its starting value. The battery’s rise is balanced by the drops across the resistors, so the total is not equal to the battery’s potential difference. Resistance and current are not potential differences.
5

Part 5 of 5: Use the loop rule when a circuit cannot be reduced

Series and parallel reduction works for many circuits, but not all. Reach for the loop rule when batteries sit in different branches. Use it too when you need an unknown potential difference inside a loop.

  • Label each unknown current and assume a direction for it.
  • Choose a loop and a direction of travel.
  • Write the loop equation term by term, using the sign rules.
  • Repeat for other independent loops, then solve the equations together.
  • Check the signs and units of each answer.

Finish by testing a result in a loop you did not use. The potential differences should again sum to zero.

Note read

Check your recall[12 marks]

6 written questions. Answer each one in your head or on paper, then open the mark scheme.

  1. 1.Describe[2 marks]

    Describe Kirchhoff’s loop rule and the conservation law it reflects.

    Show mark schemeHide mark scheme

    Model answer

    The sum of the potential differences around any closed loop is zero. The rule reflects conservation of energy.

    • 1 mark for stating that potential differences around a closed loop sum to zero
    • 1 mark for identifying conservation of energy
  2. 2.Calculate[2 marks]

    Calculate the current in a single loop containing a 9.0 V battery, a 2.0 Ω2.0\,\Omega2.0Ω resistor and a 4.0 Ω4.0\,\Omega4.0Ω resistor.

    Show mark schemeHide mark scheme

    Model answer

    +9.0 V−I(2.0 Ω)−I(4.0 Ω)=0+9.0\,\mathrm{V}-I(2.0\,\Omega)-I(4.0\,\Omega)=0+9.0V−I(2.0Ω)−I(4.0Ω)=0, so I=9.0 V6.0 Ω=1.5 AI=\frac{9.0\,\mathrm{V}}{6.0\,\Omega}=1.5\,\mathrm{A}I=6.0Ω9.0V​=1.5A.

    • 1 mark for writing the loop equation 9.0−2.0I−4.0I=09.0-2.0I-4.0I=09.0−2.0I−4.0I=0 in volts
    • 1 mark for obtaining 1.5 A1.5\,\mathrm{A}1.5A
  3. 3.Determine[3 marks]

    A 20 V battery and an 8.0 V battery oppose each other in one loop with a total resistance of 6.0 Ω6.0\,\Omega6.0Ω. Determine the current and its direction.

    Show mark schemeHide mark scheme

    Model answer

    The net potential difference is 20 V−8.0 V=12 V20\,\mathrm{V}-8.0\,\mathrm{V}=12\,\mathrm{V}20V−8.0V=12V. I=12 V6.0 Ω=2.0 AI=\frac{12\,\mathrm{V}}{6.0\,\Omega}=2.0\,\mathrm{A}I=6.0Ω12V​=2.0A, in the direction set by the 20 V battery.

    • 1 mark for writing the loop equation with opposite signs for the two batteries
    • 1 mark for obtaining 2.0 A2.0\,\mathrm{A}2.0A
    • 1 mark for identifying the direction as that driven by the larger battery
  4. 4.Explain[2 marks]

    Explain what a negative value for a current means after solving a loop equation.

    Show mark schemeHide mark scheme

    Model answer

    The current is opposite in direction to the one assumed when the equation was written. Its size is still correct.

    • 1 mark for stating that the actual current is opposite to the assumed direction
    • 1 mark for stating that the magnitude is unaffected
  5. 5.Identify[1 mark]

    Identify the sign of a resistor’s term in a loop equation when the loop is traveled against the current.

    Show mark schemeHide mark scheme

    Model answer

    The term is positive, +IR+IR+IR.

    • 1 mark for stating that the sign is positive
  6. 6.Justify[2 marks]

    Justify, using the loop rule, why two resistors in parallel have the same potential difference across them.

    Show mark schemeHide mark scheme

    Model answer

    Take a loop down one resistor and up the other. The rule gives −I2R2+I3R3=0-I_2R_2+I_3R_3=0−I2​R2​+I3​R3​=0, so I2R2=I3R3I_2R_2=I_3R_3I2​R2​=I3​R3​. The two potential differences are equal.

    • 1 mark for applying the loop rule to a loop through both resistors
    • 1 mark for concluding that I2R2=I3R3I_2R_2=I_3R_3I2​R2​=I3​R3​, so the potential differences are equal

Practice this topic

10 quick-fire multiple-choice questions, easy to hard. Tap an answer to see if you're right and the worked explanation. (The written questions with mark schemes are under “Check your recall” above.)

0 right0 of 10 answered

Includes the 2 quick checks in the note above.

3.

Easy[1 mark]

A loop is traveled in the same direction as the current through a resistor. What is the term for that resistor in the loop equation?
Show answer and explanation

Answer: B · Worked explanation

The potential decreases along the direction of the current, so the term is −IR-IR−IR. The term +IR+IR+IR applies only when traveling against the current. A term of zero would need no current or no resistance. The ratio IR\frac{I}{R}RI​ is not a potential difference.
4.

Medium·Calculate[2 marks]

Calculate the current in a single loop containing an 18 V18\,\mathrm{V}18V battery, a 5.0 Ω5.0\,\Omega5.0Ω resistor and a 4.0 Ω4.0\,\Omega4.0Ω resistor.
Show answer and explanation

Answer: B · Worked explanation

The loop equation is 18−5.0I−4.0I=018-5.0I-4.0I=018−5.0I−4.0I=0, so I=18 V9.0 Ω=2.0 AI=\frac{18\,\mathrm{V}}{9.0\,\Omega}=2.0\,\mathrm{A}I=9.0Ω18V​=2.0A. The value 3.6 A3.6\,\mathrm{A}3.6A uses only the 5.0 Ω5.0\,\Omega5.0Ω resistor. The value 4.5 A4.5\,\mathrm{A}4.5A uses only the 4.0 Ω4.0\,\Omega4.0Ω resistor. Each ignores the potential drop across the other resistor. In a single loop the same current passes through both resistors, so their potential drops add.
5.

Medium·Determine[2 marks]

A 15 V15\,\mathrm{V}15V battery and a 9.0 V9.0\,\mathrm{V}9.0V battery oppose each other in a single loop with a total resistance of 3.0 Ω3.0\,\Omega3.0Ω. Determine the current.
Show answer and explanation

Answer: B · Worked explanation

The net potential difference is 15 V−9.0 V=6.0 V15\,\mathrm{V}-9.0\,\mathrm{V}=6.0\,\mathrm{V}15V−9.0V=6.0V, so I=6.0 V3.0 Ω=2.0 AI=\frac{6.0\,\mathrm{V}}{3.0\,\Omega}=2.0\,\mathrm{A}I=3.0Ω6.0V​=2.0A. The value 8.0 A8.0\,\mathrm{A}8.0A adds the batteries as if they aided each other. The value 5.0 A5.0\,\mathrm{A}5.0A ignores the opposing battery. Opposing batteries partly cancel, so only their difference drives the current. The value 3.0 A3.0\,\mathrm{A}3.0A uses only the smaller battery.
6.

Medium·Determine[2 marks]

A single loop has a 12 V12\,\mathrm{V}12V battery and three resistors. Traveling in the direction of the current, the changes across two of the resistors are −5.0 V-5.0\,\mathrm{V}−5.0V and −3.0 V-3.0\,\mathrm{V}−3.0V. Determine the change across the third resistor.
Show answer and explanation

Answer: B · Worked explanation

The loop rule gives +12−5.0−3.0+ΔV3=0+12-5.0-3.0+\Delta V_3=0+12−5.0−3.0+ΔV3​=0, so ΔV3=−4.0 V\Delta V_3=-4.0\,\mathrm{V}ΔV3​=−4.0V. A positive value would make the sum +8.0 V+8.0\,\mathrm{V}+8.0V, not zero. The value −20 V-20\,\mathrm{V}−20V simply adds the battery and the two known changes as if all were drops, −12−5.0−3.0-12-5.0-3.0−12−5.0−3.0, instead of solving for the missing term. Rises and drops must cancel exactly around the loop, so the third term has to balance the other terms.
7.

Medium[2 marks]

A student solves a loop equation and finds I=−0.80 AI=-0.80\,\mathrm{A}I=−0.80A. What does the negative sign mean?
Show answer and explanation

Answer: A · Worked explanation

The sign only compares the true direction with the assumed one. A negative result means the current flows opposite to the assumed direction, and its size is still 0.80 A. The sign does not record a potential drop, and it does not signal an error. The loop equation sums to zero for every valid current.
8.

Hard·Determine[2 marks]

A 12 V12\,\mathrm{V}12V battery and a 6.0 V6.0\,\mathrm{V}6.0V battery are in a single loop so that they push current in the same direction. The total resistance is 3.0 Ω3.0\,\Omega3.0Ω. Determine the current.
Show answer and explanation

Answer: C · Worked explanation

Aiding batteries add: +12+6.0−3.0I=0+12+6.0-3.0I=0+12+6.0−3.0I=0, so I=18 V3.0 Ω=6.0 AI=\frac{18\,\mathrm{V}}{3.0\,\Omega}=6.0\,\mathrm{A}I=3.0Ω18V​=6.0A. The value 2.0 A2.0\,\mathrm{A}2.0A is the result for opposing batteries. The value 4.0 A4.0\,\mathrm{A}4.0A uses only the larger battery. The value 18 A18\,\mathrm{A}18A forgets to divide by the resistance. Aiding batteries raise the potential twice around the loop, so their gains add.
9.

Hard·Determine[2 marks]

A 12 V12\,\mathrm{V}12V battery is connected to a 2.0 Ω2.0\,\Omega2.0Ω resistor in series with a parallel pair of 3.0 Ω3.0\,\Omega3.0Ω and 6.0 Ω6.0\,\Omega6.0Ω resistors. Determine the potential difference across the 3.0 Ω3.0\,\Omega3.0Ω resistor.
Show answer and explanation

Answer: B · Worked explanation

The pair is 2.0 Ω2.0\,\Omega2.0Ω, so Req=4.0 ΩR_\mathrm{eq}=4.0\,\OmegaReq​=4.0Ω and I=3.0 AI=3.0\,\mathrm{A}I=3.0A in the 2.0 Ω2.0\,\Omega2.0Ω resistor. A loop through the battery, that resistor and the 3.0 Ω3.0\,\Omega3.0Ω resistor gives 12−6.0−ΔV=012-6.0-\Delta V=012−6.0−ΔV=0, so ΔV=6.0 V\Delta V=6.0\,\mathrm{V}ΔV=6.0V. The value 9.0 V9.0\,\mathrm{V}9.0V multiplies the total current by 3.0 Ω3.0\,\Omega3.0Ω, though only part of the current passes through it.
10.

Hard[2 marks]

Which statement about Kirchhoff’s loop rule is correct?
Show answer and explanation

Answer: C · Worked explanation

The rule comes from conservation of energy, so it holds for every closed loop in every circuit. A loop through two parallel resistors has no battery, and the potential differences around it still sum to zero. The current does not need to be the same in every element, and circuits with several loops obey it for each loop.

Keep going

Next topic11.7 Kirchhoff's junction rulePrevious topic11.5 Compound DC circuits

More in Unit 11 · Electric Circuits

  1. 11.1Electric currentNotes · 10 questions
  2. 11.2Simple circuitsNotes · 10 questions
  3. 11.3Resistance, resistivity and Ohm's lawNotes · 10 questions
  4. 11.4Electric powerNotes · 10 questions
  5. 11.5Compound DC circuitsNotes · 10 questions
  6. 11.6Kirchhoff's loop ruleNotes · 10 questions
  7. 11.7Kirchhoff's junction ruleNotes · 10 questions
  8. 11.8RC circuitsNotes · 10 questions

All AP Physics 2 topics →

Draft: written by Scribe and checked automatically, not yet by a subject reviewer.

Practice questions are original, written by Scribe and checked automatically for correctness.

Topic codes follow the official numbering. Not endorsed by College Board or any exam board.

On this page

0/5 read

  1. 1Potential differences around a closed loop add to zero
  2. 2Each circuit element adds a signed term to the equation
  3. 3A single loop gives one equation for one unknown current
  4. 4Every independent loop in a larger circuit gives an equation
  5. 5Use the loop rule when a circuit cannot be reduced
  6. Check your recall
  7. Practice: 10 questions
All coursesScribeHow it worksPricingPrivacyTerms

Notes and questions are written by Scribe in our own words. Topic codes follow the official course numbering so you can find your place. Not produced or endorsed by the IB, College Board, AQA, OCR, Pearson Edexcel or any exam board.

© 2026 Scribe