Scribe logoScribeNotes & practice
Sign inStart free
  1. Notes
  2. ›AQA A-level Physics
  3. ›3.4 Mechanics and materials
  4. ›3.4.2.2 The Young modulus

AQA A-level Physics · Section 3.4 · Mechanics and materials

3.4.2.2 The Young modulus

Define stress, strain and the Young modulus, calculate it from experimental data, interpret stress–strain graphs and explain how it guides the choice of materials.

  • 4 min read
  • 5 parts
  • 10 questions
  • Draft
Start a Quick 5 on this topic→Jump to the 10 questions
1/5Stress and strain remove the effect of sample size
  1. 1Stress and strain remove the effect of sample size
  2. 2The Young modulus is stress divided by strain
  3. 3A long thin wire gives a measurable extension
  4. 4Stress–strain graphs reveal how a material behaves
  5. 5A high Young modulus suits parts that must stay stiff
  6. Check your recall
  7. Practice: 10 questions
1

Part 1 of 5: Stress and strain remove the effect of sample size

A thick rope stretches less than a thin one under the same load. Comparing materials fairly needs a measure that ignores size. Tensile stress divides the force by the cross-sectional area, so σ=FA\sigma=\frac{F}{A}σ=AF​.

A long wire also stretches more than a short one. Tensile strain removes this effect by dividing the extension by the original length, so ε=ΔLL\varepsilon=\frac{\Delta L}{L}ε=LΔL​.

Strain has no unit, because both lengths are measured in metres. Stress is measured in pascals, where 1 Pa=1 N m−21\,\mathrm{Pa}=1\,\mathrm{N\,m^{-2}}1Pa=1Nm−2.

Common mistake

Do not put the diameter into πr2\pi r^{2}πr2. Halve it first, so that A=π(d2)2A=\pi\left(\frac{d}{2}\right)^{2}A=π(2d​)2.

Key terms · tap one for its definition

tensile stress

Tensile stress is the force applied per unit cross-sectional area, σ=FA\sigma=\frac{F}{A}σ=AF​, measured in pascals (Pa\mathrm{Pa}Pa).

tensile strain

Tensile strain is the extension per unit original length, ε=ΔLL\varepsilon=\frac{\Delta L}{L}ε=LΔL​, and it has no unit.

Part 1 done

2

Part 2 of 5: The Young modulus is stress divided by strain

Now join the two ideas. While Hooke’s law holds, stress is proportional to strain. Their ratio is therefore constant for a given material. This constant is the Young modulus, EEE.

In symbols, E=σε=FLAΔLE=\frac{\sigma}{\varepsilon}=\frac{FL}{A\Delta L}E=εσ​=AΔLFL​. The unit is the pascal, because strain has no unit. A large EEE means a stiff material that strains very little under load.

The value depends on the material, not on the size or shape of the sample. This makes it a fair way to compare materials.

Worked example

Young modulus of a steel wire

A steel wire of original length 2.5 m and diameter 0.40 mm carries a force of 60 N. It extends by 6.0 mm. Calculate the Young modulus of the steel.
  1. 1
    Area: A=π(d2)2=π×(2.0×10−4 m)2=1.26×10−7 m2A=\pi\left(\frac{d}{2}\right)^{2}=\pi\times(2.0\times10^{-4}\,\mathrm{m})^{2}=1.26\times10^{-7}\,\mathrm{m^{2}}A=π(2d​)2=π×(2.0×10−4m)2=1.26×10−7m2.
  2. 2
    Stress: σ=FA=60 N1.26×10−7 m2=4.76×108 Pa\sigma=\frac{F}{A}=\frac{60\,\mathrm{N}}{1.26\times10^{-7}\,\mathrm{m^{2}}}=4.76\times10^{8}\,\mathrm{Pa}σ=AF​=1.26×10−7m260N​=4.76×108Pa.
  3. 3
    Strain: ε=ΔLL=6.0×10−3 m2.5 m=2.4×10−3\varepsilon=\frac{\Delta L}{L}=\frac{6.0\times10^{-3}\,\mathrm{m}}{2.5\,\mathrm{m}}=2.4\times10^{-3}ε=LΔL​=2.5m6.0×10−3m​=2.4×10−3.
  4. 4
    Young modulus: E=σε=4.76×108 Pa2.4×10−3=1.98×1011 PaE=\frac{\sigma}{\varepsilon}=\frac{4.76\times10^{8}\,\mathrm{Pa}}{2.4\times10^{-3}}=1.98\times10^{11}\,\mathrm{Pa}E=εσ​=2.4×10−34.76×108Pa​=1.98×1011Pa.

Answer: The Young modulus is 2.0×1011 Pa2.0\times10^{11}\,\mathrm{Pa}2.0×1011Pa.

Key term

Young modulus

The Young modulus EEE is the ratio of tensile stress to tensile strain, E=σεE=\frac{\sigma}{\varepsilon}E=εσ​, measured in pascals.

Part 2 done

Quick check

One question on the part you just read

Easy

Identify the unit of the Young modulus.
Show answer and explanation

Answer: C · Worked explanation

The Young modulus is stress divided by strain. Stress is force per area in N m−2\mathrm{N\,m^{-2}}Nm−2, and strain has no unit, so the Young modulus has the unit N m−2\mathrm{N\,m^{-2}}Nm−2, which is the pascal. The unit N m−1\mathrm{N\,m^{-1}}Nm−1 belongs to a spring constant, which is force per unit extension rather than force per unit area.
3

Part 3 of 5: A long thin wire gives a measurable extension

Next, consider how EEE is found in a laboratory. A long, thin wire gives a measurable extension for modest loads. The method has five steps.

  • Measure the diameter at several places with a micrometer, then take the mean.
  • Measure the original length from the clamp to a marker with a metre rule.
  • Add masses one at a time and note the marker’s position each time.
  • Find each force from F=mgF=mgF=mg, using g=9.8 m s−2g=9.8\,\mathrm{m\,s^{-2}}g=9.8ms−2, and each extension from the marker’s movement.
  • Plot force against extension and find the gradient.
Figure 1. A marker on the wire moves along a metre rule as masses are added. The movement of the marker gives the extension.

The gradient is FΔL\frac{F}{\Delta L}ΔLF​, which equals EAL\frac{EA}{L}LEA​. So E=LA×FΔLE=\frac{L}{A}\times\frac{F}{\Delta L}E=AL​×ΔLF​, using the gradient and the measured LLL and AAA.

Exam tip

Measure the diameter carefully. It is squared when you find AAA, so it dominates the uncertainty in EEE.

Part 3 done

4

Part 4 of 5: Stress–strain graphs reveal how a material behaves

Plotting stress against strain removes sample size from the graph. The straight section starts at the origin. Its gradient is the Young modulus, and the line ends where the material stops obeying Hooke’s law.

A ductile metal then curves as it deforms plastically. The highest stress it reaches is the tensile strength, and the material soon fractures after this.

Figure 2. The initial straight line has gradient E. The curve rises to a maximum stress, the tensile strength, before the wire fractures.

The area under a stress–strain graph is the energy stored in each cubic metre of material. For the straight section the area is 12σε\frac{1}{2}\sigma\varepsilon21​σε, in J m−3\mathrm{J\,m^{-3}}Jm−3.

Common mistake

The gradient of a stress–strain graph is the Young modulus. The gradient of a force–extension graph is not, because it depends on the size of the sample.

Key term

tensile strength

The tensile strength of a material is the maximum tensile force per unit cross-sectional area it can bear before it breaks.

Part 4 done

Quick check

One question on the part you just read

Easy

State what is meant by tensile strain.
Show answer and explanation

Answer: C · Worked explanation

Tensile strain is extension divided by original length, ε=ΔLL\varepsilon=\frac{\Delta L}{L}ε=LΔL​. Force divided by cross-sectional area is tensile stress, a different quantity. Dividing the original length by the extension inverts the ratio, so a longer extension would wrongly give a smaller strain.
5

Part 5 of 5: A high Young modulus suits parts that must stay stiff

Engineers choose materials by their properties. For a cable or a support, small strain under load matters. A material with a high Young modulus gives a small strain for a given stress.

A low Young modulus suits parts that must flex, such as a rubber band. For two wires with the same size and load, strain is inversely proportional to EEE. If EEE doubles, the strain halves.

Exam tip

Stiffness and strength are different. A stiff material can still be brittle. When you justify a choice, state which property you mean.

Note read

Check your recall[15 marks]

6 written questions. Answer each one in your head or on paper, then open the mark scheme.

  1. 1.State[2 marks]

    State what is meant by tensile strain and give its unit.

    Show mark schemeHide mark scheme

    Model answer

    Tensile strain is the extension per unit original length, ΔLL\frac{\Delta L}{L}LΔL​. It has no unit because it is a ratio of two lengths.

    • 1 mark for stating that strain is extension divided by original length
    • 1 mark for stating that it has no unit
  2. 2.Calculate[3 marks]

    A wire of cross-sectional area 2.0×10−7 m22.0\times10^{-7}\,\mathrm{m^{2}}2.0×10−7m2 and original length 1.5 m1.5\,\mathrm{m}1.5m extends by 1.2 mm1.2\,\mathrm{mm}1.2mm under a force of 40 N40\,\mathrm{N}40N. Calculate the Young modulus of its material.

    Show mark schemeHide mark scheme

    Model answer

    Stress =402.0×10−7=2.0×108 Pa=\frac{40}{2.0\times10^{-7}}=2.0\times10^{8}\,\mathrm{Pa}=2.0×10−740​=2.0×108Pa. Strain =1.2×10−31.5=8.0×10−4=\frac{1.2\times10^{-3}}{1.5}=8.0\times10^{-4}=1.51.2×10−3​=8.0×10−4. So E=2.0×1088.0×10−4=2.5×1011 PaE=\frac{2.0\times10^{8}}{8.0\times10^{-4}}=2.5\times10^{11}\,\mathrm{Pa}E=8.0×10−42.0×108​=2.5×1011Pa.

    • 1 mark for calculating the stress as 2.0×108 Pa2.0\times10^{8}\,\mathrm{Pa}2.0×108Pa
    • 1 mark for calculating the strain as 8.0×10−48.0\times10^{-4}8.0×10−4
    • 1 mark for obtaining E=2.5×1011 PaE=2.5\times10^{11}\,\mathrm{Pa}E=2.5×1011Pa
  3. 3.Describe[4 marks]

    Describe how a student measures the original length, the diameter and the extension of a wire in an experiment to find the Young modulus.

    Show mark schemeHide mark scheme

    Model answer

    Measure the original length from the clamp to a marker with a metre rule. Measure the diameter with a micrometer at several places and take the mean. Add masses one at a time. Record the marker’s position against the rule each time, and find the extension from its movement.

    • 1 mark for measuring the original length with a metre rule
    • 1 mark for measuring the diameter with a micrometer at several places and averaging
    • 1 mark for adding masses in steps
    • 1 mark for finding the extension from the marker’s movement along a rule
  4. 4.Explain[2 marks]

    Explain why a long, thin wire is used when measuring the Young modulus.

    Show mark schemeHide mark scheme

    Model answer

    A long, thin wire gives a large extension for a small load. The extension can then be measured with small percentage error using a metre rule.

    • 1 mark for stating that a long thin wire gives a large extension for a small force
    • 1 mark for linking the large extension to more accurate measurement
  5. 5.Suggest[3 marks]

    Suggest why a material with a high Young modulus may still be unsuitable for a cable that must carry a heavy load.

    Show mark schemeHide mark scheme

    Model answer

    A high Young modulus means the material is stiff, not that it is strong. The material may have a low tensile strength, or be brittle. The cable could then break at a low stress without stretching much first.

    • 1 mark for stating that a high Young modulus means stiffness
    • 1 mark for stating that this is not the same as strength or tensile strength
    • 1 mark for suggesting that the material may be brittle or break at low stress
  6. 6.State[1 mark]

    State the quantity given by the gradient of the straight section of a stress–strain graph.

    Show mark schemeHide mark scheme

    Model answer

    The gradient is the Young modulus.

    • 1 mark for stating the Young modulus

Practice this topic

10 quick-fire multiple-choice questions, easy to hard. Tap an answer to see if you're right and the worked explanation. (The written questions with mark schemes are under “Check your recall” above.)

0 right0 of 10 answered

Includes the 2 quick checks in the note above.

3.

Easy·Identify[1 mark]

Identify the quantity found by dividing the force applied to a wire by its cross-sectional area.
Show answer and explanation

Answer: D · Worked explanation

Force divided by cross-sectional area is tensile stress, σ=FA\sigma=\frac{F}{A}σ=AF​. The Young modulus is a different ratio, found by dividing this stress by the strain. Tensile strain is the extension divided by the original length and does not involve the force directly.
4.

Medium·Calculate[2 marks]

A force of 150 N150\,\mathrm{N}150N is applied to a wire of diameter 0.60 mm0.60\,\mathrm{mm}0.60mm. Calculate the tensile stress.
Show answer and explanation

Answer: B · Worked explanation

The radius is 0.30 mm=3.0×10−4 m0.30\,\mathrm{mm}=3.0\times10^{-4}\,\mathrm{m}0.30mm=3.0×10−4m, so A=πr2=2.83×10−7 m2A=\pi r^{2}=2.83\times10^{-7}\,\mathrm{m^{2}}A=πr2=2.83×10−7m2. Then σ=1502.83×10−7=5.3×108 Pa\sigma=\frac{150}{2.83\times10^{-7}}=5.3\times10^{8}\,\mathrm{Pa}σ=2.83×10−7150​=5.3×108Pa. The value 1.3×1081.3\times10^{8}1.3×108 comes from using the diameter as the radius, which makes the area four times too large. The value 5.3×1055.3\times10^{5}5.3×105 comes from converting square millimetres to square metres with the wrong power of ten.
5.

Medium·Calculate[2 marks]

A wire of original length 2.0 m2.0\,\mathrm{m}2.0m extends by 1.5 mm1.5\,\mathrm{mm}1.5mm. Calculate the tensile strain.
Show answer and explanation

Answer: C · Worked explanation

Convert the extension to metres: 1.5 mm=1.5×10−3 m1.5\,\mathrm{mm}=1.5\times10^{-3}\,\mathrm{m}1.5mm=1.5×10−3m. Then ε=ΔLL=1.5×10−32.0=7.5×10−4\varepsilon=\frac{\Delta L}{L}=\frac{1.5\times10^{-3}}{2.0}=7.5\times10^{-4}ε=LΔL​=2.01.5×10−3​=7.5×10−4. The value 7.5×10−17.5\times10^{-1}7.5×10−1 comes from dividing 1.5 by 2.0 without converting millimetres to metres, which mixes two different length units. Strain is a ratio of two lengths in the same unit, so it has no unit.
6.

Medium·Calculate[2 marks]

On the straight section of a stress–strain graph, the stress is 4.0×108 Pa4.0\times10^{8}\,\mathrm{Pa}4.0×108Pa when the strain is 2.0×10−32.0\times10^{-3}2.0×10−3. Calculate the Young modulus.
Show answer and explanation

Answer: D · Worked explanation

The Young modulus is the gradient, E=σε=4.0×1082.0×10−3=2.0×1011 PaE=\frac{\sigma}{\varepsilon}=\frac{4.0\times10^{8}}{2.0\times10^{-3}}=2.0\times10^{11}\,\mathrm{Pa}E=εσ​=2.0×10−34.0×108​=2.0×1011Pa. The value 8.0×1058.0\times10^{5}8.0×105 comes from multiplying stress by strain. The value 5.0×10−125.0\times10^{-12}5.0×10−12 comes from dividing strain by stress, which inverts the ratio. The gradient of a stress–strain graph is stress divided by strain, so check which quantity is on each axis.
7.

Medium·Predict[2 marks]

Two wires, P and Q, are made of the same material and have the same cross-sectional area. Q is twice as long as P. The same force is applied to each. Predict the extension of Q and its Young modulus compared with P.
Show answer and explanation

Answer: A · Worked explanation

The stress is the same in both wires, so the strain is the same. Extension equals strain multiplied by original length, so the longer wire Q extends twice as far. The Young modulus belongs to the material, so it is unchanged. Doubling the Young modulus would wrongly treat it as depending on length.
8.

Hard·Predict[2 marks]

Two wires are made of the same material and have the same length. Wire B has half the diameter of wire A. The same force is applied to both. Predict the extension of B compared with A.
Show answer and explanation

Answer: D · Worked explanation

The area depends on diameter squared, so halving the diameter makes the area one quarter. The stress becomes four times larger. With the same material and length, strain and extension also become four times larger. A prediction of twice as large wrongly treats the area as proportional to diameter.
9.

Hard·Calculate[2 marks]

Stress rises in proportion to strain up to 3.0×108 Pa3.0\times10^{8}\,\mathrm{Pa}3.0×108Pa at a strain of 1.6×10−31.6\times10^{-3}1.6×10−3. Calculate the energy stored per unit volume at this point.
Show answer and explanation

Answer: C · Worked explanation

The graph is a straight line, so the area is a triangle and energy per unit volume is 12σε=12×3.0×108×1.6×10−3=2.4×105 J m−3\frac{1}{2}\sigma\varepsilon=\frac{1}{2}\times3.0\times10^{8}\times1.6\times10^{-3}=2.4\times10^{5}\,\mathrm{J\,m^{-3}}21​σε=21​×3.0×108×1.6×10−3=2.4×105Jm−3. The value 4.8×1054.8\times10^{5}4.8×105 leaves out the factor of one half. The value 1.9×10111.9\times10^{11}1.9×1011 is the Young modulus, not an energy. The area under the graph up to this point is a triangle, which is why the factor of one half appears.
10.

Hard·Calculate[2 marks]

A wire of cross-sectional area 2.0×10−6 m22.0\times10^{-6}\,\mathrm{m^{2}}2.0×10−6m2 supports a mass of 40 kg40\,\mathrm{kg}40kg. Its Young modulus is 2.0×1011 Pa2.0\times10^{11}\,\mathrm{Pa}2.0×1011Pa. Use g=9.8 m s−2g=9.8\,\mathrm{m\,s^{-2}}g=9.8ms−2. Calculate the strain.
Show answer and explanation

Answer: B · Worked explanation

The force is the weight, F=mg=40×9.8=392 NF=mg=40\times9.8=392\,\mathrm{N}F=mg=40×9.8=392N. The stress is 3922.0×10−6=1.96×108 Pa\frac{392}{2.0\times10^{-6}}=1.96\times10^{8}\,\mathrm{Pa}2.0×10−6392​=1.96×108Pa. The strain is 1.96×1082.0×1011=9.8×10−4\frac{1.96\times10^{8}}{2.0\times10^{11}}=9.8\times10^{-4}2.0×10111.96×108​=9.8×10−4. The value 1.0×10−41.0\times10^{-4}1.0×10−4 comes from using the mass as the force instead of the weight. The value 1.0×1031.0\times10^{3}1.0×103 comes from dividing the Young modulus by the stress, which inverts the relationship.

Keep going

Next topic3.5.1.1 Basics of electricityPrevious topic3.4.2.1 Bulk properties of solids

More in Section 3.4 · Mechanics and materials

  1. 3.4.1.2MomentsNotes · 10 questions
  2. 3.4.1.3Motion in a straight lineNotes · 10 questions
  3. 3.4.1.4Projectile motionNotes · 10 questions
  4. 3.4.1.5Newton's laws of motionNotes · 10 questions
  5. 3.4.1.6MomentumNotes · 10 questions
  6. 3.4.1.7Work, energy and powerNotes · 10 questions
  7. 3.4.1.8Conservation of energyNotes · 9 questions
  8. 3.4.2.1Bulk properties of solidsNotes · 10 questions
  9. 3.4.2.2The Young modulusNotes · 10 questions

All AQA A-level Physics topics →

Draft: written by Scribe and checked automatically, not yet by a subject reviewer.

Practice questions are original, written by Scribe and checked automatically for correctness.

Topic codes follow the official numbering. Not endorsed by AQA or any exam board.

On this page

0/5 read

  1. 1Stress and strain remove the effect of sample size
  2. 2The Young modulus is stress divided by strain
  3. 3A long thin wire gives a measurable extension
  4. 4Stress–strain graphs reveal how a material behaves
  5. 5A high Young modulus suits parts that must stay stiff
  6. Check your recall
  7. Practice: 10 questions
All coursesScribeHow it worksPricingPrivacyTerms

Notes and questions are written by Scribe in our own words. Topic codes follow the official course numbering so you can find your place. Not produced or endorsed by the IB, College Board, AQA, OCR, Pearson Edexcel or any exam board.

© 2026 Scribe

Stress–strain graph for a ductile metal

Stress (×10⁸ Pa)012345670123456Strain (×10⁻³)
  • Straight part
  • Plastic part
  • Beyond maximum
  • Limit of proportionality
  • Tensile strength
  • Fracture