Scribe logoScribeNotes & practice
Sign inStart free
  1. Notes
  2. ›AQA A-level Physics
  3. ›3.5 Electricity
  4. ›3.5.1.1 Basics of electricity

AQA A-level Physics · Section 3.5 · Electricity

3.5.1.1 Basics of electricity

Define charge, current, potential difference and resistance, explain current flow in metals, use ammeters and voltmeters, and apply Q=ItQ=ItQ=It and Ohm’s law.

  • 4 min read
  • 5 parts
  • 10 questions
  • Draft
Start a Quick 5 on this topic→Jump to the 10 questions
1/5Current is the rate at which charge flows
  1. 1Current is the rate at which charge flows
  2. 2Free electrons carry current through a metal
  3. 3Potential difference drives current and resistance opposes it
  4. 4Ammeters and voltmeters must be connected in the right way
  5. 5Charge, current and resistance link through two relationships
  6. Check your recall
  7. Practice: 10 questions
1

Part 1 of 5: Current is the rate at which charge flows

Rub a balloon on your hair and it sticks to a wall. Both objects have gained charge, which causes electric forces. We measure it in coulombs.

In a circuit, charge moves along the wires. Current is the rate of this flow, I=ΔQΔtI=\frac{\Delta Q}{\Delta t}I=ΔtΔQ​. A current of 1 A1\,\mathrm{A}1A means 1 C1\,\mathrm{C}1C passes a point every second.

For a steady current, this becomes Q=ItQ=ItQ=It, with time ttt in seconds. A larger current moves more coulombs each second.

The charge on one electron is very small, with magnitude 1.60×10−19 C1.60\times10^{-19}\,\mathrm{C}1.60×10−19C. A current of 1 A1\,\mathrm{A}1A therefore involves a vast number of electrons each second.

Key terms · tap one for its definition

charge

Charge is a property of matter, symbol QQQ, measured in coulombs (C\mathrm{C}C), that causes electric forces.

current

Current is the rate of flow of charge, I=ΔQΔtI=\frac{\Delta Q}{\Delta t}I=ΔtΔQ​, measured in amperes (A\mathrm{A}A).

Part 1 done

2

Part 2 of 5: Free electrons carry current through a metal

Metals conduct because they contain free electrons. These electrons are not bound to single atoms, so they move through the lattice of positive ions.

A potential difference makes the electrons drift along the wire, colliding with ions as they go. Their mean velocity along the wire is the drift velocity, vvv.

Electrons are negative, so they drift towards the positive terminal. By convention, current is drawn the opposite way. This is conventional current.

These ideas combine in I=nAvqI=nAvqI=nAvq, where:

  • nnn is the number of free electrons per unit volume, in m−3\mathrm{m^{-3}}m−3
  • AAA is the cross-sectional area, in m2\mathrm{m^{2}}m2
  • vvv is the drift velocity, in m s−1\mathrm{m\,s^{-1}}ms−1
  • qqq is the charge on one electron, of magnitude 1.60×10−19 C1.60\times10^{-19}\,\mathrm{C}1.60×10−19C

Worked example

Drift velocity in a wire

A wire has 8.0×10288.0\times10^{28}8.0×1028 free electrons per cubic metre and a cross-sectional area of 2.0×10−6 m22.0\times10^{-6}\,\mathrm{m^{2}}2.0×10−6m2. It carries a current of 4.0 A. Calculate the drift velocity.
  1. 1
    Rearrange I=nAvqI=nAvqI=nAvq to give v=InAqv=\frac{I}{nAq}v=nAqI​.
  2. 2
    Find the denominator: nAq=8.0×1028×2.0×10−6×1.60×10−19=2.56×104nAq=8.0\times10^{28}\times2.0\times10^{-6}\times1.60\times10^{-19}=2.56\times10^{4}nAq=8.0×1028×2.0×10−6×1.60×10−19=2.56×104.
  3. 3
    Substitute: v=4.02.56×104v=\frac{4.0}{2.56\times10^{4}}v=2.56×1044.0​.

Answer: The drift velocity is 1.6×10−4 m s−11.6\times10^{-4}\,\mathrm{m\,s^{-1}}1.6×10−4ms−1.

Key terms · tap one for its definition

free electron

Free electrons are electrons in a metal that are not bound to individual atoms and act as the charge carriers.

drift velocity

The drift velocity vvv is the mean velocity of charge carriers along a conductor, measured in m s−1\mathrm{m\,s^{-1}}ms−1.

conventional current

Conventional current is the direction in which positive charge would flow, from the positive terminal to the negative terminal.

Part 2 done

Quick check

One question on the part you just read

Easy

Identify which expression is equal to one coulomb.
Show answer and explanation

Answer: B · Worked explanation

Charge is current multiplied by time, Q=ItQ=ItQ=It, so one coulomb is one ampere second. The unit A s−1\mathrm{A\,s^{-1}}As−1 would divide by time instead. The expression V A−1\mathrm{V\,A^{-1}}VA−1 is the ohm, the unit of resistance, and J s−1\mathrm{J\,s^{-1}}Js−1 is the watt. Remember that current is charge per second, so charge is current multiplied by seconds.
3

Part 3 of 5: Potential difference drives current and resistance opposes it

Think of a pump pushing water round a pipe. A cell does the same job for charge. The potential difference between two points measures the energy transferred for each coulomb.

In symbols, V=WQV=\frac{W}{Q}V=QW​, where WWW is the energy transferred in joules. One volt is one joule per coulomb, so 1 V=1 J C−11\,\mathrm{V}=1\,\mathrm{J\,C^{-1}}1V=1JC−1.

Both quantities matter in a circuit. A larger potential difference across the same resistance gives a larger current. A larger resistance at the same potential difference gives a smaller current.

The wire and components oppose the flow of charge. Resistance measures this opposition, R=VIR=\frac{V}{I}R=IV​. Its unit is the ohm, Ω\OmegaΩ, where 1 Ω=1 V A−11\,\Omega=1\,\mathrm{V\,A^{-1}}1Ω=1VA−1.

Key terms · tap one for its definition

potential difference

The energy transferred per unit charge between two points, measured in volts.

resistance

Resistance is the ratio of potential difference across a component to current through it.

Part 3 done

4

Part 4 of 5: Ammeters and voltmeters must be connected in the right way

To measure these quantities you need two meters. An ammeter measures current. It sits in series, so all the current passes through it.

A voltmeter measures potential difference. It is connected across the component being tested, so only a tiny current passes through it.

Figure 1. The ammeter is in series with the resistor. The voltmeter is connected in parallel across it. The arrow shows conventional current.

Ammeter and voltmeter compared

MeterMeasuresConnectionIdeal resistance
AmmeterCurrentIn seriesZero
VoltmeterPotential differenceIn parallelInfinite
Meter
Ammeter
Measures
Current
Connection
In series
Ideal resistance
Zero
Meter
Voltmeter
Measures
Potential difference
Connection
In parallel
Ideal resistance
Infinite

An ideal ammeter has zero resistance, so it does not reduce the current. An ideal voltmeter has infinite resistance, so it draws no current.

Common mistake

A voltmeter in series leaves almost no current in the circuit, because its resistance is so high.

Key terms · tap one for its definition

ammeter

An ammeter measures current and is connected in series.

voltmeter

A voltmeter measures potential difference and is connected in parallel.

Part 4 done

Quick check

One question on the part you just read

Easy

State how a voltmeter is connected to measure the potential difference across a component.
Show answer and explanation

Answer: A · Worked explanation

A voltmeter measures the potential difference between two points, so it is connected in parallel across the component. Connecting it in series would place its very high resistance in the loop and block the current. Joining it only to the cell would measure the cell’s potential difference, not the component’s.
5

Part 5 of 5: Charge, current and resistance link through two relationships

Questions often give a current and a time and ask for the charge. Use Q=ItQ=ItQ=It with the time in seconds. Convert minutes before you substitute.

Resistance in a metal is often constant. Ohm’s law describes this case. For such a conductor, V=IRV=IRV=IR gives a fixed value of RRR.

Common mistake

The equation V=IRV=IRV=IR defines resistance and works for every component. Ohm’s law is the special case where RRR stays constant.

Always check units. Potential difference in volts and resistance in ohms give current in amperes. Current in amperes and time in seconds give charge in coulombs.

Worked example

Charge through a resistor

A 6.0 Ω6.0\,\Omega6.0Ω resistor is connected across a 9.0 V9.0\,\mathrm{V}9.0V cell for 30 s. Calculate the charge that passes through it.
  1. 1
    Current: I=VR=9.0 V6.0 Ω=1.5 AI=\frac{V}{R}=\frac{9.0\,\mathrm{V}}{6.0\,\Omega}=1.5\,\mathrm{A}I=RV​=6.0Ω9.0V​=1.5A.
  2. 2
    Charge: Q=It=1.5 A×30 sQ=It=1.5\,\mathrm{A}\times30\,\mathrm{s}Q=It=1.5A×30s.

Answer: The charge is 45 C45\,\mathrm{C}45C.

Key term

Ohm’s law

Ohm’s law states that current is proportional to potential difference when physical conditions remain constant.

Note read

Check your recall[15 marks]

6 written questions. Answer each one in your head or on paper, then open the mark scheme.

  1. 1.State[2 marks]

    State what an ammeter measures and how it is connected in a circuit.

    Show mark schemeHide mark scheme

    Model answer

    An ammeter measures current. It is connected in series with the component.

    • 1 mark for stating that an ammeter measures current
    • 1 mark for stating that it is connected in series
  2. 2.Describe[3 marks]

    Describe how current flows in a metal wire connected to a cell.

    Show mark schemeHide mark scheme

    Model answer

    The metal contains free electrons that are not bound to single atoms. The potential difference makes these electrons drift along the wire towards the positive terminal. They collide with ions on the way, so their mean drift velocity is small.

    • 1 mark for stating that free electrons carry the current
    • 1 mark for stating that the potential difference makes them drift towards the positive terminal
    • 1 mark for stating that collisions with ions keep the drift velocity small or give a mean velocity
  3. 3.Calculate[3 marks]

    A resistor of resistance 12 Ω12\,\Omega12Ω has a potential difference of 4.8 V4.8\,\mathrm{V}4.8V across it for 25 s25\,\mathrm{s}25s. Calculate the charge that passes through it.

    Show mark schemeHide mark scheme

    Model answer

    I=VR=4.812=0.40 AI=\frac{V}{R}=\frac{4.8}{12}=0.40\,\mathrm{A}I=RV​=124.8​=0.40A. Then Q=It=0.40×25=10 CQ=It=0.40\times25=10\,\mathrm{C}Q=It=0.40×25=10C.

    • 1 mark for using I=VRI=\frac{V}{R}I=RV​ to find 0.40 A0.40\,\mathrm{A}0.40A
    • 1 mark for using Q=ItQ=ItQ=It
    • 1 mark for obtaining 10 C10\,\mathrm{C}10C
  4. 4.State[2 marks]

    State Ohm’s law.

    Show mark schemeHide mark scheme

    Model answer

    The current in a conductor is proportional to the potential difference across it. This applies when physical conditions such as temperature stay constant.

    • 1 mark for stating that current is proportional to potential difference
    • 1 mark for stating that physical conditions such as temperature must remain constant
  5. 5.Explain[2 marks]

    Explain why a voltmeter should have a very high resistance.

    Show mark schemeHide mark scheme

    Model answer

    A voltmeter is connected in parallel across a component. A very high resistance means it draws almost no current, so it does not change the current or potential difference being measured.

    • 1 mark for stating that the voltmeter takes a negligible current
    • 1 mark for linking this to the circuit being unchanged so the reading is accurate
  6. 6.Calculate[3 marks]

    A wire has 5.0×10285.0\times10^{28}5.0×1028 free electrons per cubic metre and a cross-sectional area of 1.0 mm21.0\,\mathrm{mm^{2}}1.0mm2. It carries a current of 2.0 A2.0\,\mathrm{A}2.0A. Calculate the drift velocity. The charge on an electron has magnitude 1.60×10−19 C1.60\times10^{-19}\,\mathrm{C}1.60×10−19C.

    Show mark schemeHide mark scheme

    Model answer

    The area is 1.0×10−6 m21.0\times10^{-6}\,\mathrm{m^{2}}1.0×10−6m2. Then v=InAq=2.05.0×1028×1.0×10−6×1.60×10−19=2.5×10−4 m s−1v=\frac{I}{nAq}=\frac{2.0}{5.0\times10^{28}\times1.0\times10^{-6}\times1.60\times10^{-19}}=2.5\times10^{-4}\,\mathrm{m\,s^{-1}}v=nAqI​=5.0×1028×1.0×10−6×1.60×10−192.0​=2.5×10−4ms−1.

    • 1 mark for converting the area to 1.0×10−6 m21.0\times10^{-6}\,\mathrm{m^{2}}1.0×10−6m2
    • 1 mark for rearranging to v=InAqv=\frac{I}{nAq}v=nAqI​
    • 1 mark for obtaining 2.5×10−4 m s−12.5\times10^{-4}\,\mathrm{m\,s^{-1}}2.5×10−4ms−1

Practice this topic

10 quick-fire multiple-choice questions, easy to hard. Tap an answer to see if you're right and the worked explanation. (The written questions with mark schemes are under “Check your recall” above.)

0 right0 of 10 answered

Includes the 2 quick checks in the note above.

3.

Easy·Identify[1 mark]

Identify the direction of conventional current in a circuit.
Show answer and explanation

Answer: C · Worked explanation

Conventional current is the direction positive charge would flow, from the positive terminal round the circuit to the negative terminal. Electrons in a metal drift the opposite way, because they carry negative charge. So saying it follows the electron flow confuses the real motion of electrons with the convention.
4.

Medium·Calculate[1 mark]

A steady current of 0.30 A0.30\,\mathrm{A}0.30A flows for 5.0 minutes. Calculate the charge that passes.
Show answer and explanation

Answer: D · Worked explanation

Convert the time to seconds: 5.0 min=300 s5.0\,\mathrm{min}=300\,\mathrm{s}5.0min=300s. Then Q=It=0.30×300=90 CQ=It=0.30\times300=90\,\mathrm{C}Q=It=0.30×300=90C. The value 1.5 C1.5\,\mathrm{C}1.5C comes from using 5.0 as the time in seconds. The value 1.0×1031.0\times10^{3}1.0×103 comes from dividing time by current instead of multiplying. Always convert minutes to seconds before using Q=ItQ=ItQ=It.
5.

Medium·Calculate[2 marks]

A resistor obeys Ohm’s law. The current through it is 0.20 A0.20\,\mathrm{A}0.20A when the potential difference is 6.0 V6.0\,\mathrm{V}6.0V. Calculate the current when the potential difference is 15 V15\,\mathrm{V}15V.
Show answer and explanation

Answer: D · Worked explanation

The resistance is R=6.00.20=30 ΩR=\frac{6.0}{0.20}=30\,\OmegaR=0.206.0​=30Ω, so I=VR=1530=0.50 AI=\frac{V}{R}=\frac{15}{30}=0.50\,\mathrm{A}I=RV​=3015​=0.50A. Equally, the current scales in proportion to the potential difference. The value 3.0 A3.0\,\mathrm{A}3.0A comes from multiplying 0.20 by 15 rather than by the ratio 156.0\frac{15}{6.0}6.015​. The value 75 A75\,\mathrm{A}75A comes from dividing 15 by 0.20, which gives a resistance-style number rather than a current.
6.

Medium·Calculate[2 marks]

A 12 V12\,\mathrm{V}12V supply moves 5.0 C5.0\,\mathrm{C}5.0C of charge through a lamp. Calculate the energy transferred.
Show answer and explanation

Answer: A · Worked explanation

Potential difference is energy per unit charge, so W=QV=5.0×12=60 JW=QV=5.0\times12=60\,\mathrm{J}W=QV=5.0×12=60J. The value 2.4 J2.4\,\mathrm{J}2.4J comes from dividing the potential difference by the charge, which inverts the relationship. The value 17 J17\,\mathrm{J}17J comes from adding the two numbers, which has no physical meaning here.
7.

Medium·Identify[1 mark]

Identify the correct description of the resistance of ideal meters.
Show answer and explanation

Answer: B · Worked explanation

An ideal ammeter has zero resistance so that it does not reduce the current it is measuring. An ideal voltmeter has infinite resistance so that it draws no current from the component. The reverse arrangement would make the ammeter block the current and the voltmeter act like a short circuit.
8.

Hard·Calculate[2 marks]

A 15 Ω15\,\Omega15Ω resistor has a potential difference of 6.0 V6.0\,\mathrm{V}6.0V across it for 40 s40\,\mathrm{s}40s. Calculate the charge that passes through it.
Show answer and explanation

Answer: C · Worked explanation

First find the current: I=VR=6.015=0.40 AI=\frac{V}{R}=\frac{6.0}{15}=0.40\,\mathrm{A}I=RV​=156.0​=0.40A. Then Q=It=0.40×40=16 CQ=It=0.40\times40=16\,\mathrm{C}Q=It=0.40×40=16C. The value 6.0×1026.0\times10^{2}6.0×102 comes from multiplying resistance by time. The value 2.4×1022.4\times10^{2}2.4×102 comes from multiplying potential difference by time, which skips the current. The value 0.010 C0.010\,\mathrm{C}0.010C comes from dividing the current by the time, which is the wrong way round.
9.

Hard·Predict[2 marks]

A wire of uniform cross-section carries a steady current. It is joined in series to a thinner section of the same metal with half the cross-sectional area. Predict how the drift velocity in the thin section compares with that in the wire.
Show answer and explanation

Answer: D · Worked explanation

The current is the same in series and the free electron density nnn and charge qqq are unchanged. From I=nAvqI=nAvqI=nAvq, the drift velocity vvv is inversely proportional to AAA, so halving the area doubles vvv. Saying the drift velocity is the same wrongly assumes that equal current means equal velocity.
10.

Hard·Determine[2 marks]

A component passes 0.20 A0.20\,\mathrm{A}0.20A at 4.0 V4.0\,\mathrm{V}4.0V and 0.35 A0.35\,\mathrm{A}0.35A at 8.0 V8.0\,\mathrm{V}8.0V. Determine what this shows.
Show answer and explanation

Answer: C · Worked explanation

Ohm’s law needs current to be proportional to potential difference. Doubling 4.0 V4.0\,\mathrm{V}4.0V to 8.0 V8.0\,\mathrm{V}8.0V would give 0.40 A0.40\,\mathrm{A}0.40A, but the current is only 0.35 A0.35\,\mathrm{A}0.35A. The equation V=IRV=IRV=IR holds at every point because it defines resistance, so it cannot show that Ohm’s law is obeyed.

Keep going

Next topic3.5.1.2 Current–voltage characteristicsPrevious topic3.4.2.2 The Young modulus

More in Section 3.5 · Electricity

  1. 3.5.1.1Basics of electricityNotes · 10 questions
  2. 3.5.1.2Current–voltage characteristicsNotes · 10 questions
  3. 3.5.1.3ResistivityNotes · 10 questions
  4. 3.5.1.4CircuitsNotes · 10 questions
  5. 3.5.1.5Potential dividersNotes · 10 questions
  6. 3.5.1.6EMF and internal resistanceNotes · 10 questions

All AQA A-level Physics topics →

Draft: written by Scribe and checked automatically, not yet by a subject reviewer.

Practice questions are original, written by Scribe and checked automatically for correctness.

Topic codes follow the official numbering. Not endorsed by AQA or any exam board.

On this page

0/5 read

  1. 1Current is the rate at which charge flows
  2. 2Free electrons carry current through a metal
  3. 3Potential difference drives current and resistance opposes it
  4. 4Ammeters and voltmeters must be connected in the right way
  5. 5Charge, current and resistance link through two relationships
  6. Check your recall
  7. Practice: 10 questions
All coursesScribeHow it worksPricingPrivacyTerms

Notes and questions are written by Scribe in our own words. Topic codes follow the official course numbering so you can find your place. Not produced or endorsed by the IB, College Board, AQA, OCR, Pearson Edexcel or any exam board.

© 2026 Scribe