Scribe logoScribeNotes & practice
Sign inStart free
  1. Notes
  2. ›AQA A-level Physics
  3. ›3.5 Electricity
  4. ›3.5.1.3 Resistivity

AQA A-level Physics · Section 3.5 · Electricity

3.5.1.3 Resistivity

Define resistivity, use the resistance equation for a wire, and describe how temperature and light change the resistance of metals, thermistors and LDRs.

  • 4 min read
  • 6 parts
  • 10 questions
  • Draft
Start a Quick 5 on this topic→Jump to the 10 questions
1/6A longer, thinner wire has more resistance
  1. 1A longer, thinner wire has more resistance
  2. 2Resistivity measures how strongly a material resists current
  3. 3The resistance equation lets us calculate wire resistance
  4. 4Heating a metal increases its resistance
  5. 5Heating a semiconductor lowers its resistance
  6. 6Light lowers the resistance of an LDR
  7. Check your recall
  8. Practice: 10 questions
1

Part 1 of 6: A longer, thinner wire has more resistance

Water flows less easily through a long, narrow pipe than through a short, wide one. A metal wire treats charge in a similar way. Its shape affects how hard it is to push current through.

This opposition is the resistance RRR of the wire. It is found from R=VIR=\frac{V}{I}R=IV​ and measured in ohms, Ω\OmegaΩ. Here VVV is the potential difference across the wire and III is the current through it.

For one material, resistance is proportional to length LLL. It is inversely proportional to cross-sectional area AAA. Doubling the length doubles the resistance, but doubling the area halves it.

Key term

resistance

Resistance is the ratio of potential difference across a component to current through it.

Part 1 done

2

Part 2 of 6: Resistivity measures how strongly a material resists current

Copper and nichrome wires of identical size have very different resistances. The difference comes from the material, not the shape. We need a quantity that describes the material alone.

That quantity is the resistivity ρ\rhoρ of the material. For a uniform conductor, ρ=RAL\rho=\frac{RA}{L}ρ=LRA​. Its unit is the ohm metre, Ω m\Omega\,\mathrm{m}Ωm.

Rearranging gives the resistance equation R=ρLAR=\frac{\rho L}{A}R=AρL​. At a fixed temperature, ρ\rhoρ is constant for a given material.

Common mistake

Resistivity is not resistance. Resistance depends on the size of the sample, but resistivity does not. Their units are Ω\OmegaΩ and Ω m\Omega\,\mathrm{m}Ωm.

Key term

resistivity

A material property equal to RA/LRA/LRA/L for a uniform conductor, measured in Ω m\Omega\,\mathrm{m}Ωm.

Part 2 done

Quick check

One question on the part you just read

Easy

Identify the SI unit of resistivity.
Show answer and explanation

Answer: A · Worked explanation

Resistivity is ρ=RAL\rho=\frac{RA}{L}ρ=LRA​. Its unit is Ω m2\Omega\,\mathrm{m^2}Ωm2 divided by m\mathrm{m}m, which gives Ω m\Omega\,\mathrm{m}Ωm. The unit Ω m2\Omega\,\mathrm{m^{2}}Ωm2 comes from stopping before dividing by the length. The ohm on its own is the unit of resistance, which depends on the size of a sample.
3

Part 3 of 6: The resistance equation lets us calculate wire resistance

Now put numbers into the equation. Most wires are circular, so the cross-sectional area is A=πd24A=\frac{\pi d^2}{4}A=4πd2​, where ddd is the diameter. Convert millimetres to metres before substituting.

Length must be in metres and area in square metres. Then resistivity in Ω m\Omega\,\mathrm{m}Ωm gives resistance in ohms directly. Most errors come from forgetting to square the diameter. Check that the final unit is the ohm.

A thin wire is useful where high resistance is wanted. A thick wire suits connecting leads, where the resistance should be small.

Worked example

Resistance of a copper wire

A copper wire is 2.5 m long and has a diameter of 0.50 mm. The resistivity of copper is 1.7×10−8 Ω m1.7\times10^{-8}\,\Omega\,\mathrm{m}1.7×10−8Ωm. Calculate the resistance of the wire.
  1. 1
    Find the area: A=πd24=π×(0.50×10−3 m)24=1.96×10−7 m2A=\frac{\pi d^2}{4}=\frac{\pi\times(0.50\times10^{-3}\,\mathrm{m})^2}{4}=1.96\times10^{-7}\,\mathrm{m^2}A=4πd2​=4π×(0.50×10−3m)2​=1.96×10−7m2.
  2. 2
    Resistance equals resistivity multiplied by length, divided by area: R=ρLAR=\frac{\rho L}{A}R=AρL​.
  3. 3
    Substitute: R=1.7×10−8 Ω m×2.5 m1.96×10−7 m2R=\frac{1.7\times10^{-8}\,\Omega\,\mathrm{m}\times2.5\,\mathrm{m}}{1.96\times10^{-7}\,\mathrm{m^2}}R=1.96×10−7m21.7×10−8Ωm×2.5m​.
  4. 4
    Calculate: R=4.25×10−81.96×10−7=0.217 ΩR=\frac{4.25\times10^{-8}}{1.96\times10^{-7}}=0.217\,\OmegaR=1.96×10−74.25×10−8​=0.217Ω, which rounds to 0.22 Ω0.22\,\Omega0.22Ω.

Answer: The resistance of the wire is R≈0.22 ΩR\approx0.22\,\OmegaR≈0.22Ω.

Exam tip

Halving the diameter makes the area four times smaller. The resistance of the same wire then rises fourfold.

Part 3 done

4

Part 4 of 6: Heating a metal increases its resistance

So far the temperature has been fixed. Now let the wire warm up. A higher temperature means the metal ions have more average kinetic energy.

The ions swing more widely about their fixed positions. Conduction electrons collide with them more often, so their drift slows. The number of conduction electrons stays almost unchanged.

For the same potential difference, the current falls. The resistance therefore rises. A graph of resistance against temperature for a metal climbs gently and smoothly. Over a large temperature range, as in the hot filament of a lamp, the effect becomes large.

Go deeperSuperconductors

In some materials the resistivity drops to zero at and below a critical temperature. These materials are called superconductors. Their critical temperatures are low, so they must be cooled.

A current in a superconducting loop can flow with no energy lost as heat. Superconductors are used to make very strong electromagnets.

Key term

temperature

Temperature indicates the average kinetic energy of particles in a substance.

Part 4 done

Quick check

One question on the part you just read

Easy

A wire has a resistance of 6.0 Ω6.0\,\Omega6.0Ω. A second wire of the same material and cross-sectional area is twice as long. Predict the resistance of the second wire.
Show answer and explanation

Answer: D · Worked explanation

At fixed area and material, resistance is proportional to length. Doubling the length doubles the resistance, so R=2×6.0 Ω=12 ΩR=2\times6.0\,\Omega=12\,\OmegaR=2×6.0Ω=12Ω. A value of 24 Ω24\,\Omega24Ω would need a fourfold rise, as if the length had been squared. A value of 3.0 Ω3.0\,\Omega3.0Ω would mean the longer wire resists less.
5

Part 5 of 6: Heating a semiconductor lowers its resistance

A thermistor behaves in the opposite way to a metal wire. It is made from a semiconductor, so it conducts only a little at low temperatures.

Heating releases more charge carriers. The extra carriers outweigh the increase in collisions. Resistance therefore falls as temperature rises. The change can be large over a modest temperature range, which makes the material a sensitive sensor.

A thermistor is a component made from this kind of material. Many are small beads with two leads. They are used as temperature sensors in thermostats and fire alarms.

Figure 1. A metal wire’s resistance rises gently with temperature. A thermistor’s resistance falls steeply. The values are illustrative.

Key terms · tap one for its definition

semiconductor

A semiconductor is a material with far fewer charge carriers than a metal, a number that rises when it is heated or illuminated.

thermistor

A thermistor is a resistor whose resistance changes strongly with temperature; the common type falls in resistance as temperature rises.

Part 5 done

6

Part 6 of 6: Light lowers the resistance of an LDR

Light can also release charge carriers in a semiconductor. This is how a light-dependent resistor works.

An LDR has a thin layer of semiconductor, often cadmium sulfide, between two metal contacts. Light gives energy to charge carriers in the layer. More carriers are free to move, so resistance falls.

In the dark its resistance is very high. In bright light it is much lower. LDRs are used in light meters and in lights that switch on at dusk.

Exam tip

Describe the cause as well as the trend. Say that more charge carriers are released, so the resistance falls.

Key term

light-dependent resistor

A light-dependent resistor (LDR) is a component whose resistance decreases as the intensity of light falling on it increases.

Note read

Check your recall[14 marks]

5 written questions. Answer each one in your head or on paper, then open the mark scheme.

  1. 1.State[2 marks]

    State what is meant by the resistivity of a material and give its unit.

    Show mark schemeHide mark scheme

    Model answer

    Resistivity is a property of the material equal to RAL\frac{RA}{L}LRA​ for a uniform conductor, where RRR is resistance, AAA is cross-sectional area and LLL is length. Its unit is the ohm metre, Ω m\Omega\,\mathrm{m}Ωm.

    • 1 mark for stating that resistivity equals RAL\frac{RA}{L}LRA​ for a uniform conductor, with the symbols identified
    • 1 mark for giving the unit as the ohm metre, Ω m\Omega\,\mathrm{m}Ωm
  2. 2.Calculate[4 marks]

    Calculate the resistance of a 4.0 m length of copper wire with a diameter of 0.40 mm. The resistivity of copper is 1.7×10−8 Ω m1.7\times10^{-8}\,\Omega\,\mathrm{m}1.7×10−8Ωm.

    Show mark schemeHide mark scheme

    Model answer

    Area A=πd24=π×(0.40×10−3)24=1.26×10−7 m2A=\frac{\pi d^2}{4}=\frac{\pi\times(0.40\times10^{-3})^2}{4}=1.26\times10^{-7}\,\mathrm{m^2}A=4πd2​=4π×(0.40×10−3)2​=1.26×10−7m2. Then R=ρLA=1.7×10−8×4.01.26×10−7=0.54 ΩR=\frac{\rho L}{A}=\frac{1.7\times10^{-8}\times4.0}{1.26\times10^{-7}}=0.54\,\OmegaR=AρL​=1.26×10−71.7×10−8×4.0​=0.54Ω.

    • 1 mark for using A=πd24A=\frac{\pi d^2}{4}A=4πd2​ with the diameter converted to metres
    • 1 mark for obtaining A≈1.26×10−7 m2A\approx1.26\times10^{-7}\,\mathrm{m^2}A≈1.26×10−7m2
    • 1 mark for substituting into R=ρLAR=\frac{\rho L}{A}R=AρL​
    • 1 mark for obtaining 0.54 Ω0.54\,\Omega0.54Ω
  3. 3.Explain[3 marks]

    Explain why the resistance of a metal wire increases as its temperature rises.

    Show mark schemeHide mark scheme

    Model answer

    The metal ions vibrate with a larger amplitude at higher temperature. Conduction electrons therefore collide with the ions more often. The number of conduction electrons is almost unchanged, so their drift slows and resistance rises.

    • 1 mark for stating that the ions vibrate with larger amplitude at higher temperature
    • 1 mark for stating that conduction electrons collide with the ions more often
    • 1 mark for stating that the number of conduction electrons is almost unchanged, so current falls and resistance rises
  4. 4.Explain[3 marks]

    Explain why the resistance of a thermistor made from a semiconductor falls as its temperature rises.

    Show mark schemeHide mark scheme

    Model answer

    A semiconductor has few charge carriers at low temperature. Heating releases more charge carriers. The extra carriers outweigh the increased collisions, so resistance falls.

    • 1 mark for stating that a semiconductor has few charge carriers at low temperature
    • 1 mark for stating that heating releases more charge carriers
    • 1 mark for concluding that more carriers means a lower resistance
  5. 5.Suggest[2 marks]

    Suggest why an LDR could be used to detect when it becomes dark.

    Show mark schemeHide mark scheme

    Model answer

    The resistance of an LDR is high in the dark and falls in bright light. A circuit can detect this change in resistance and switch a light on.

    • 1 mark for stating that the resistance of an LDR depends on light intensity, high in the dark and low in bright light
    • 1 mark for stating that a circuit can detect the change in resistance to respond

Practice this topic

10 quick-fire multiple-choice questions, easy to hard. Tap an answer to see if you're right and the worked explanation. (The written questions with mark schemes are under “Check your recall” above.)

0 right0 of 10 answered

Includes the 2 quick checks in the note above.

3.

Easy·Identify[1 mark]

Identify the correct statement about the resistivity of a copper wire at constant temperature.
Show answer and explanation

Answer: D · Worked explanation

Resistivity is a property of the material, so it does not depend on the size of the sample at a fixed temperature. Length and area change the resistance, not the resistivity. The statement that resistivity is measured in ohms confuses it with resistance. Resistivity is measured in Ω m\Omega\,\mathrm{m}Ωm.
4.

Medium·Calculate[2 marks]

A wire has resistivity 5.0×10−7 Ω m5.0\times10^{-7}\,\Omega\,\mathrm{m}5.0×10−7Ωm, length 0.80 m and cross-sectional area 2.0×10−7 m22.0\times10^{-7}\,\mathrm{m^2}2.0×10−7m2. Calculate its resistance.
Show answer and explanation

Answer: A · Worked explanation

Use R=ρLA=5.0×10−7×0.802.0×10−7=2.0 ΩR=\frac{\rho L}{A}=\frac{5.0\times10^{-7}\times0.80}{2.0\times10^{-7}}=2.0\,\OmegaR=AρL​=2.0×10−75.0×10−7×0.80​=2.0Ω. The value 2.5 Ω2.5\,\Omega2.5Ω comes from leaving out the length and calculating ρA\frac{\rho}{A}Aρ​, which is the resistance of a wire one metre long. The value 0.50 Ω0.50\,\Omega0.50Ω comes from inverting the equation to AρL\frac{A}{\rho L}ρLA​, which puts the area on the wrong side.
5.

Medium·Calculate[2 marks]

A circular wire has a diameter of 0.60 mm. Calculate its cross-sectional area.
Show answer and explanation

Answer: D · Worked explanation

Use A=πd24=π×(0.60×10−3)24=2.8×10−7 m2A=\frac{\pi d^2}{4}=\frac{\pi\times(0.60\times10^{-3})^2}{4}=2.8\times10^{-7}\,\mathrm{m^2}A=4πd2​=4π×(0.60×10−3)2​=2.8×10−7m2. The value 1.1×10−6 m21.1\times10^{-6}\,\mathrm{m^2}1.1×10−6m2 comes from using πd2\pi d^2πd2 and forgetting the factor of four. The value 3.6×10−7 m23.6\times10^{-7}\,\mathrm{m^2}3.6×10−7m2 comes from squaring the diameter and omitting π4\frac{\pi}{4}4π​. Check that the diameter has been converted from millimetres to metres first, and that the result is in square metres.
6.

Medium·Explain[1 mark]

Explain why the resistance of a metal wire increases when it is heated.
Show answer and explanation

Answer: C · Worked explanation

At higher temperature the ions have more kinetic energy and vibrate with a larger amplitude. Conduction electrons collide with the ions more often and drift more slowly, so resistance rises. The number of conduction electrons stays almost unchanged in a metal. The claim that more electrons are released describes a semiconductor, in which resistance falls.
7.

Medium·Predict[1 mark]

A thermistor and an LDR are moved from a cold, dark room into a warm, bright room. Predict how the resistance of each changes.
Show answer and explanation

Answer: B · Worked explanation

Warming releases more charge carriers in the semiconductor of the thermistor, so its resistance falls. Bright light releases more charge carriers in the LDR, so its resistance falls too. The idea that the thermistor resistance rises treats it like a metal wire. A metal wire behaves in the opposite way, because collisions increase.
8.

Hard·Determine[2 marks]

A uniform wire has a resistance of 3.0 Ω3.0\,\Omega3.0Ω. It is stretched to twice its original length. Its volume and resistivity stay constant. Determine its new resistance.
Show answer and explanation

Answer: A · Worked explanation

The volume is area multiplied by length, so doubling the length halves the area. Resistance is proportional to LA\frac{L}{A}AL​, so it changes by 21/2=4\frac{2}{1/2}=41/22​=4. The new resistance is 4×3.0 Ω=12 Ω4\times3.0\,\Omega=12\,\Omega4×3.0Ω=12Ω. The value 6.0 Ω6.0\,\Omega6.0Ω comes from doubling the length while forgetting that the area falls.
9.

Hard·Determine[2 marks]

Wire X has length LLL and diameter ddd and a resistance of 8.0 Ω8.0\,\Omega8.0Ω. Wire Y is made of the same material and has length 2L2L2L and diameter 2d2d2d. Determine the resistance of wire Y.
Show answer and explanation

Answer: D · Worked explanation

Doubling the length doubles the resistance. Doubling the diameter makes the area four times larger, which divides the resistance by four. The net factor is 24=12\frac{2}{4}=\frac{1}{2}42​=21​, so wire Y has 4.0 Ω4.0\,\Omega4.0Ω. The value 8.0 Ω8.0\,\Omega8.0Ω comes from treating a doubled diameter as a doubled area, so the two changes cancel.
10.

Hard·Identify[2 marks]

A wire is replaced by one of the same material at the same temperature. The new wire is three times as long and has three times the cross-sectional area. Identify the correct statement.
Show answer and explanation

Answer: C · Worked explanation

Resistance is proportional to LA\frac{L}{A}AL​, and both quantities increase by a factor of three, so the resistance does not change. Resistivity belongs to the material at a fixed temperature, so it does not change either. A threefold rise in resistance would result from lengthening the wire alone.

Keep going

Next topic3.5.1.4 CircuitsPrevious topic3.5.1.2 Current–voltage characteristics

More in Section 3.5 · Electricity

  1. 3.5.1.1Basics of electricityNotes · 10 questions
  2. 3.5.1.2Current–voltage characteristicsNotes · 10 questions
  3. 3.5.1.3ResistivityNotes · 10 questions
  4. 3.5.1.4CircuitsNotes · 10 questions
  5. 3.5.1.5Potential dividersNotes · 10 questions
  6. 3.5.1.6EMF and internal resistanceNotes · 10 questions

All AQA A-level Physics topics →

Draft: written by Scribe and checked automatically, not yet by a subject reviewer.

Practice questions are original, written by Scribe and checked automatically for correctness.

Topic codes follow the official numbering. Not endorsed by AQA or any exam board.

On this page

0/6 read

  1. 1A longer, thinner wire has more resistance
  2. 2Resistivity measures how strongly a material resists current
  3. 3The resistance equation lets us calculate wire resistance
  4. 4Heating a metal increases its resistance
  5. 5Heating a semiconductor lowers its resistance
  6. 6Light lowers the resistance of an LDR
  7. Check your recall
  8. Practice: 10 questions
All coursesScribeHow it worksPricingPrivacyTerms

Notes and questions are written by Scribe in our own words. Topic codes follow the official course numbering so you can find your place. Not produced or endorsed by the IB, College Board, AQA, OCR, Pearson Edexcel or any exam board.

© 2026 Scribe

Resistance against temperature

Resistance (Ω)020406080100051015Temperature (°C)
  • Metal wire
  • Thermistor