Scribe logoScribeNotes & practice
Sign inStart free
  1. Notes
  2. ›AQA A-level Physics
  3. ›3.5 Electricity
  4. ›3.5.1.5 Potential dividers

AQA A-level Physics · Section 3.5 · Electricity

3.5.1.5 Potential dividers

Describe how a potential divider shares a supply, calculate its output potential difference, and explain how thermistors and LDRs make it respond to temperature or light.

  • 4 min read
  • 5 parts
  • 10 questions
  • Draft
Start a Quick 5 on this topic→Jump to the 10 questions
1/5A potential divider shares a supply between two resistors
  1. 1A potential divider shares a supply between two resistors
  2. 2Output p.d. depends on the ratio of the resistances
  3. 3The larger resistor takes the larger share of the input
  4. 4A thermistor makes the output depend on temperature
  5. 5An LDR makes the output depend on light level
  6. Check your recall
  7. Practice: 10 questions
1

Part 1 of 5: A potential divider shares a supply between two resistors

A hill can be climbed in two stages, and each stage uses part of the total height. Two resistors in series share a supply in a similar way. Each takes part of the total energy per coulomb. The potential difference (p.d.) across each is a fraction of the supply p.d.

A potential divider uses this to give a smaller, chosen p.d. from a larger supply.

The supply p.d. is the input, VinV_\mathrm{in}Vin​. The p.d. across one resistor is the output, VoutV_\mathrm{out}Vout​. The same current flows through both resistors.

Figure 1. A cell supplies the input p.d. across two resistors in series. The output p.d. is taken across the lower resistor.

Key term

potential divider

A series-resistor arrangement that provides an output potential difference across part of the circuit.

Part 1 done

2

Part 2 of 5: Output p.d. depends on the ratio of the resistances

To find the output, start with the current. Both resistors carry I=VinR1+R2I=\frac{V_\mathrm{in}}{R_1+R_2}I=R1​+R2​Vin​​. The output p.d. across R2R_2R2​ is then Vout=IR2V_\mathrm{out}=IR_2Vout​=IR2​.

Combining these gives Vout=R2R1+R2×VinV_\mathrm{out}=\frac{R_2}{R_1+R_2}\times V_\mathrm{in}Vout​=R1​+R2​R2​​×Vin​. The fraction is the share of the total resistance that lies across the output. It is always less than one, so the output is always smaller than the input. Resistances can stay in kilohms, because the units cancel in the ratio. If R1R_1R1​ equals R2R_2R2​, the fraction is one half.

Worked example

Output of a potential divider

A 12 V supply is connected across R1=6.0 kΩR_1=6.0\,\mathrm{k\Omega}R1​=6.0kΩ and R2=3.0 kΩR_2=3.0\,\mathrm{k\Omega}R2​=3.0kΩ in series. The output is taken across R2R_2R2​. Calculate VoutV_\mathrm{out}Vout​.
  1. 1
    Use Vout=R2R1+R2×VinV_\mathrm{out}=\frac{R_2}{R_1+R_2}\times V_\mathrm{in}Vout​=R1​+R2​R2​​×Vin​.
  2. 2
    Substitute: Vout=3.0 kΩ6.0 kΩ+3.0 kΩ×12 VV_\mathrm{out}=\frac{3.0\,\mathrm{k\Omega}}{6.0\,\mathrm{k\Omega}+3.0\,\mathrm{k\Omega}}\times12\,\mathrm{V}Vout​=6.0kΩ+3.0kΩ3.0kΩ​×12V.
  3. 3
    Calculate: Vout=13×12 V=4.0 VV_\mathrm{out}=\frac{1}{3}\times12\,\mathrm{V}=4.0\,\mathrm{V}Vout​=31​×12V=4.0V.

Answer: The output p.d. is 4.0 V.

Exam tip

Check which resistor the output is across. Using the other resistor gives the remaining share of the supply.

Part 2 done

Quick check

One question on the part you just read

Easy

Identify the main purpose of a potential divider.
Show answer and explanation

Answer: D · Worked explanation

A potential divider shares a supply across two resistors in series and takes the output across one of them. The output is therefore a fraction of the input and cannot exceed it. A divider cannot raise the p.d. above the supply value. The current is the same in both resistors, because they are in series.
3

Part 3 of 5: The larger resistor takes the larger share of the input

Next, change one resistor and watch the output. The output rises when the resistance across it rises. It falls when that resistance falls.

  • Equal resistors give an output of half the input.
  • A large R2R_2R2​ gives an output close to VinV_\mathrm{in}Vin​.
  • A small R2R_2R2​ gives an output close to zero.

The output always lies between zero and VinV_\mathrm{in}Vin​.

Many circuits connect a load, such as a lamp, across the output. The load and R2R_2R2​ are then in parallel, so their combined resistance is smaller than R2R_2R2​. The output p.d. falls.

Common mistake

Do not use the simple ratio formula once a load is connected. It assumes the output draws almost no current.

Key term

load

A load is a component or device connected across the output of a divider, which draws current from it.

Part 3 done

4

Part 4 of 5: A thermistor makes the output depend on temperature

Replacing one fixed resistor with a sensor lets the output follow a physical quantity. A thermistor is one such sensor. When it warms, its resistance falls, because more charge carriers are released. The change in resistance is large enough to give a clear change in output.

Suppose the thermistor is R2R_2R2​, with the output across it. Heating lowers R2R_2R2​, so its share of the supply falls. The output falls as the temperature rises.

Swapping the thermistor and the fixed resistor reverses the effect. With the output across the fixed resistor, the output rises as the temperature rises.

Worked example

A thermistor divider

A 5.0 V supply is connected across a fixed 10 kΩ10\,\mathrm{k\Omega}10kΩ resistor R1R_1R1​ in series with a thermistor R2R_2R2​. The output is across the thermistor. Its resistance is 10 kΩ10\,\mathrm{k\Omega}10kΩ at 20 °C and 2.0 kΩ2.0\,\mathrm{k\Omega}2.0kΩ at 60 °C. Calculate VoutV_\mathrm{out}Vout​ at each temperature.
  1. 1
    Use Vout=R2R1+R2×VinV_\mathrm{out}=\frac{R_2}{R_1+R_2}\times V_\mathrm{in}Vout​=R1​+R2​R2​​×Vin​.
  2. 2
    At 20 °C: Vout=1010+10×5.0 V=2.5 VV_\mathrm{out}=\frac{10}{10+10}\times5.0\,\mathrm{V}=2.5\,\mathrm{V}Vout​=10+1010​×5.0V=2.5V.
  3. 3
    At 60 °C: Vout=2.010+2.0×5.0 V=0.83 VV_\mathrm{out}=\frac{2.0}{10+2.0}\times5.0\,\mathrm{V}=0.83\,\mathrm{V}Vout​=10+2.02.0​×5.0V=0.83V.

Answer: The output is 2.5 V at 20 °C and falls to 0.83 V at 60 °C.

Key term

thermistor

A thermistor is a resistor whose resistance changes strongly with temperature; the common type falls in resistance as temperature rises.

Part 4 done

Quick check

One question on the part you just read

Easy

Two equal resistors form a potential divider across an 8.0 V supply. Determine the output p.d. across one resistor.
Show answer and explanation

Answer: D · Worked explanation

Equal resistors carry the same current and so have equal p.d. across them. Each takes half of the supply, which is 4.0 V4.0\,\mathrm{V}4.0V. The value 8.0 V would be the output if the output were taken across both resistors. The value 16 V is impossible, because it exceeds the supply p.d.
5

Part 5 of 5: An LDR makes the output depend on light level

An LDR works in the same way, but it responds to light. A light-dependent resistor has high resistance in the dark and low resistance in bright light.

Place the LDR as R2R_2R2​, with the output across it. In the dark its resistance is large, so the output is high. In bright light its resistance falls, and so does the output.

A later circuit can respond when the output passes a chosen value. For example, a lamp can switch on at dusk. The divider therefore turns a change in light into a change in p.d. that other components can use.

Exam tip

Explain a sensor circuit in three steps. The sensor’s resistance changes, so its share of the supply changes, so the output changes.

Key term

light-dependent resistor

A light-dependent resistor (LDR) is a component whose resistance decreases as the intensity of light falling on it increases.

Note read

Check your recall[14 marks]

5 written questions. Answer each one in your head or on paper, then open the mark scheme.

  1. 1.Describe[2 marks]

    Describe how a potential divider splits the supply p.d.

    Show mark schemeHide mark scheme

    Model answer

    Two resistors are connected in series across the supply, so the same current flows through both. The supply p.d. is shared in proportion to their resistances, and the output is taken across one of them.

    • 1 mark for stating that two resistors in series carry the same current
    • 1 mark for stating that the p.d. is shared in proportion to the resistances, with the output across one resistor
  2. 2.Calculate[3 marks]

    Calculate VoutV_\mathrm{out}Vout​ across R2R_2R2​ for a potential divider with Vin=9.0 VV_\mathrm{in}=9.0\,\mathrm{V}Vin​=9.0V, R1=15 kΩR_1=15\,\mathrm{k\Omega}R1​=15kΩ and R2=30 kΩR_2=30\,\mathrm{k\Omega}R2​=30kΩ.

    Show mark schemeHide mark scheme

    Model answer

    Vout=R2R1+R2×Vin=3015+30×9.0 V=6.0 VV_\mathrm{out}=\frac{R_2}{R_1+R_2}\times V_\mathrm{in}=\frac{30}{15+30}\times9.0\,\mathrm{V}=6.0\,\mathrm{V}Vout​=R1​+R2​R2​​×Vin​=15+3030​×9.0V=6.0V.

    • 1 mark for using Vout=R2R1+R2×VinV_\mathrm{out}=\frac{R_2}{R_1+R_2}\times V_\mathrm{in}Vout​=R1​+R2​R2​​×Vin​
    • 1 mark for substituting the resistances to obtain the ratio 3045\frac{30}{45}4530​
    • 1 mark for obtaining 6.0 V
  3. 3.Explain[3 marks]

    Explain why VoutV_\mathrm{out}Vout​ rises when R2R_2R2​ is increased, with VinV_\mathrm{in}Vin​ and R1R_1R1​ fixed.

    Show mark schemeHide mark scheme

    Model answer

    The same current flows through both resistors, so the p.d. is shared in proportion to resistance. A larger R2R_2R2​ is a larger fraction of the total resistance. It therefore takes a larger share of VinV_\mathrm{in}Vin​, so VoutV_\mathrm{out}Vout​ rises.

    • 1 mark for stating that the same current flows through both resistors
    • 1 mark for stating that the p.d. is shared in proportion to resistance
    • 1 mark for concluding that a larger R2R_2R2​ takes a larger share of VinV_\mathrm{in}Vin​
  4. 4.Explain[3 marks]

    Explain how VoutV_\mathrm{out}Vout​ changes as the temperature rises when a thermistor is the lower resistor of a potential divider, with the output across it.

    Show mark schemeHide mark scheme

    Model answer

    The resistance of the thermistor falls as the temperature rises. Its share of the total resistance therefore falls. It takes a smaller share of the supply p.d., so VoutV_\mathrm{out}Vout​ falls.

    • 1 mark for stating that the resistance of the thermistor falls as temperature rises
    • 1 mark for stating that its share of the total resistance falls
    • 1 mark for concluding that VoutV_\mathrm{out}Vout​ falls
  5. 5.Suggest[3 marks]

    Suggest how a divider containing an LDR could give an output that rises as the light level falls.

    Show mark schemeHide mark scheme

    Model answer

    Place the LDR as the lower resistor, with the output across it. In the dark the resistance of the LDR is high. It takes a larger share of the supply p.d., so VoutV_\mathrm{out}Vout​ is high.

    • 1 mark for placing the LDR as the resistor with the output across it
    • 1 mark for stating that the resistance of the LDR is high in the dark
    • 1 mark for linking the larger resistance to a larger share of the supply p.d. and a higher VoutV_\mathrm{out}Vout​

Practice this topic

10 quick-fire multiple-choice questions, easy to hard. Tap an answer to see if you're right and the worked explanation. (The written questions with mark schemes are under “Check your recall” above.)

0 right0 of 10 answered

Includes the 2 quick checks in the note above.

3.

Easy·Identify[1 mark]

Two resistors form a potential divider and nothing is connected to the output. Identify the correct statement about the current.
Show answer and explanation

Answer: C · Worked explanation

With nothing connected to the output, the two resistors lie on a single path, so the same current flows through both. Their p.d. differ because their resistances differ, but the current does not. The idea that a larger resistance carries a larger current confuses the p.d. with the current.
4.

Medium·Calculate[1 mark]

A potential divider has Vin=10 VV_\mathrm{in}=10\,\mathrm{V}Vin​=10V, R1=4.0 kΩR_1=4.0\,\mathrm{k\Omega}R1​=4.0kΩ and R2=1.0 kΩR_2=1.0\,\mathrm{k\Omega}R2​=1.0kΩ. Calculate VoutV_\mathrm{out}Vout​ across R2R_2R2​.
Show answer and explanation

Answer: A · Worked explanation

Use Vout=R2R1+R2×Vin=1.04.0+1.0×10 V=2.0 VV_\mathrm{out}=\frac{R_2}{R_1+R_2}\times V_\mathrm{in}=\frac{1.0}{4.0+1.0}\times10\,\mathrm{V}=2.0\,\mathrm{V}Vout​=R1​+R2​R2​​×Vin​=4.0+1.01.0​×10V=2.0V. The value 8.0 V is the p.d. across R1R_1R1​, the other share of the supply. The value 2.5 V comes from dividing by R1R_1R1​ alone instead of by the total resistance. The value 5.0 V would need equal resistors.
5.

Medium·Predict[1 mark]

A thermistor is the upper resistor of a divider and a fixed resistor is the lower one. The output is across the fixed resistor. Predict how the output changes as the temperature rises.
Show answer and explanation

Answer: D · Worked explanation

Heating lowers the resistance of the thermistor, so it takes a smaller share of the supply p.d. The remaining share goes across the fixed resistor, so the output rises. Saying that the output stays constant ignores that the share depends on the ratio of the resistances, and the ratio has changed.
6.

Medium·Calculate[2 marks]

A 6.0 V supply is connected to a 40 kΩ40\,\mathrm{k\Omega}40kΩ LDR in series with a fixed 8.0 kΩ8.0\,\mathrm{k\Omega}8.0kΩ resistor. The output is across the fixed resistor. In bright light the LDR resistance falls to 2.0 kΩ2.0\,\mathrm{k\Omega}2.0kΩ. Calculate the output in bright light.
Show answer and explanation

Answer: C · Worked explanation

Use Vout=8.02.0+8.0×6.0 V=4.8 VV_\mathrm{out}=\frac{8.0}{2.0+8.0}\times6.0\,\mathrm{V}=4.8\,\mathrm{V}Vout​=2.0+8.08.0​×6.0V=4.8V. The value 1.2 V is the p.d. across the LDR, which is the other share. The value 1.0 V is the output in the dark, when the LDR resistance is 40 kΩ40\,\mathrm{k\Omega}40kΩ and the fixed resistor takes only 8.048\frac{8.0}{48}488.0​ of the supply.
7.

Medium·Calculate[1 mark]

A 6.0 V supply is connected across a 2.0 kΩ2.0\,\mathrm{k\Omega}2.0kΩ resistor in series with a 4.0 kΩ4.0\,\mathrm{k\Omega}4.0kΩ resistor. Calculate the current.
Show answer and explanation

Answer: A · Worked explanation

The resistors are in series, so the total resistance is 6.0 kΩ6.0\,\mathrm{k\Omega}6.0kΩ. Then I=VR=6.0 V6.0 kΩ=1.0 mAI=\frac{V}{R}=\frac{6.0\,\mathrm{V}}{6.0\,\mathrm{k\Omega}}=1.0\,\mathrm{mA}I=RV​=6.0kΩ6.0V​=1.0mA. The value 3.0 mA comes from using only the 2.0 kΩ2.0\,\mathrm{k\Omega}2.0kΩ resistor. The value 1.5 mA comes from using only the 4.0 kΩ4.0\,\mathrm{k\Omega}4.0kΩ resistor. Both resistors must be included, because the same current flows through them in turn.
8.

Hard·Calculate[2 marks]

A 12 V supply is connected across R1=2.0 kΩR_1=2.0\,\mathrm{k\Omega}R1​=2.0kΩ and a resistor R2R_2R2​ in series. The output across R2R_2R2​ must be 3.0 V. Calculate R2R_2R2​.
Show answer and explanation

Answer: A · Worked explanation

The output is one quarter of the input, so R22.0+R2=14\frac{R_2}{2.0+R_2}=\frac{1}{4}2.0+R2​R2​​=41​. Then 4R2=2.0+R24R_2=2.0+R_24R2​=2.0+R2​, so R2=2.03=0.67 kΩR_2=\frac{2.0}{3}=0.67\,\mathrm{k\Omega}R2​=32.0​=0.67kΩ. The value 0.50 kΩ comes from taking one quarter of R1R_1R1​ and ignoring that R2R_2R2​ is part of the total. The value 6.0 kΩ results from taking the output across R1R_1R1​.
9.

Hard·Calculate[2 marks]

A 6.0 V supply is connected across two 1.0 kΩ1.0\,\mathrm{k\Omega}1.0kΩ resistors in series. A load of resistance 1.0 kΩ1.0\,\mathrm{k\Omega}1.0kΩ is connected across the lower resistor. Calculate the output p.d. across the lower resistor with the load connected.
Show answer and explanation

Answer: C · Worked explanation

The load and the lower resistor are in parallel, so together they have 0.50 kΩ0.50\,\mathrm{k\Omega}0.50kΩ. Then Vout=0.501.0+0.50×6.0 V=2.0 VV_\mathrm{out}=\frac{0.50}{1.0+0.50}\times6.0\,\mathrm{V}=2.0\,\mathrm{V}Vout​=1.0+0.500.50​×6.0V=2.0V. The value 3.0 V is the unloaded output, which ignores the load. The value 4.0 V would be the p.d. across the upper resistor, which now takes the larger share.
10.

Hard·Identify[2 marks]

A circuit must give an output that rises as it gets darker. Identify which arrangement achieves this.
Show answer and explanation

Answer: C · Worked explanation

In the dark the resistance of an LDR is high. With the output across the LDR, its share of the supply is larger, so the output rises. With the output across the fixed resistor, the opposite happens, because the LDR takes more of the p.d. and leaves less. An output across both resistors would just equal the supply.

Keep going

Next topic3.5.1.6 EMF and internal resistancePrevious topic3.5.1.4 Circuits

More in Section 3.5 · Electricity

  1. 3.5.1.1Basics of electricityNotes · 10 questions
  2. 3.5.1.2Current–voltage characteristicsNotes · 10 questions
  3. 3.5.1.3ResistivityNotes · 10 questions
  4. 3.5.1.4CircuitsNotes · 10 questions
  5. 3.5.1.5Potential dividersNotes · 10 questions
  6. 3.5.1.6EMF and internal resistanceNotes · 10 questions

All AQA A-level Physics topics →

Draft: written by Scribe and checked automatically, not yet by a subject reviewer.

Practice questions are original, written by Scribe and checked automatically for correctness.

Topic codes follow the official numbering. Not endorsed by AQA or any exam board.

On this page

0/5 read

  1. 1A potential divider shares a supply between two resistors
  2. 2Output p.d. depends on the ratio of the resistances
  3. 3The larger resistor takes the larger share of the input
  4. 4A thermistor makes the output depend on temperature
  5. 5An LDR makes the output depend on light level
  6. Check your recall
  7. Practice: 10 questions
All coursesScribeHow it worksPricingPrivacyTerms

Notes and questions are written by Scribe in our own words. Topic codes follow the official course numbering so you can find your place. Not produced or endorsed by the IB, College Board, AQA, OCR, Pearson Edexcel or any exam board.

© 2026 Scribe