Scribe logoScribeNotes & practice
Sign inStart free
  1. Notes
  2. ›AQA A-level Physics
  3. ›3.5 Electricity
  4. ›3.5.1.6 EMF and internal resistance

AQA A-level Physics · Section 3.5 · Electricity

3.5.1.6 EMF and internal resistance

Define electromotive force and internal resistance, use the equation for terminal potential difference, and describe how to measure both quantities experimentally.

  • 4 min read
  • 5 parts
  • 10 questions
  • Draft
Start a Quick 5 on this topic→Jump to the 10 questions
1/5A source gives energy to each coulomb of charge
  1. 1A source gives energy to each coulomb of charge
  2. 2Internal resistance causes energy loss inside the source
  3. 3Terminal potential difference falls as current increases
  4. 4A variable resistor lets us measure EMF and internal resistance
  5. 5Internal resistance limits the current a source can supply
  6. Check your recall
  7. Practice: 10 questions
1

Part 1 of 5: A source gives energy to each coulomb of charge

A cell labelled 1.5 V transfers the same energy to every coulomb of charge that passes through it. This is its electromotive force, or EMF, written ε\varepsilonε.

It is calculated from ε=EQ\varepsilon=\frac{E}{Q}ε=QE​, where EEE is the energy supplied and QQQ is the charge. One volt equals one joule per coulomb.

The EMF is not the same as the p.d. across the terminals when the cell supplies current. That p.d. is smaller. It is the terminal potential difference, VVV. Potential difference, or p.d., is the energy transferred per unit charge between two points.

EMF compared with terminal p.d.

FeatureEMF ε\varepsilonεTerminal p.d. VVV
Meaningenergy supplied per coulomb by the sourceenergy per coulomb delivered to the rest of the circuit
Effect of currentdoes not changefalls as the current rises
With no currentε\varepsilonεV=εV=\varepsilonV=ε
Feature
Meaning
EMF ε\varepsilonε
energy supplied per coulomb by the source
Terminal p.d. VVV
energy per coulomb delivered to the rest of the circuit
Feature
Effect of current
EMF ε\varepsilonε
does not change
Terminal p.d. VVV
falls as the current rises
Feature
With no current
EMF ε\varepsilonε
ε\varepsilonε
Terminal p.d. VVV
V=εV=\varepsilonV=ε

Key terms · tap one for its definition

electromotive force

The energy supplied by a source per unit charge, measured in volts.

terminal potential difference

The terminal potential difference is the potential difference VVV across the terminals of a source while it supplies a current.

Part 1 done

2

Part 2 of 5: Internal resistance causes energy loss inside the source

The terminal p.d. is lower because the source itself resists current. Energy is lost inside it. This is its internal resistance, rrr, measured in ohms.

When current III flows, the p.d. across the internal resistance is IrIrIr. This is often called the lost volts. Each coulomb gives up energy to the internal resistance, so less reaches the external circuit.

Energy conservation gives ε=V+Ir\varepsilon=V+Irε=V+Ir. Rearranging gives V=ε−IrV=\varepsilon-IrV=ε−Ir. The external resistor RRR and rrr are in series, so ε=I(R+r)\varepsilon=I(R+r)ε=I(R+r).

Common mistake

The EMF does not drop as the current grows. The terminal p.d. drops, because the lost volts IrIrIr grow.

Key term

internal resistance

Resistance within a source that reduces its terminal potential difference by IrIrIr when current III flows.

Part 2 done

Quick check

One question on the part you just read

Easy

Identify an equivalent unit for the volt, the unit of electromotive force.
Show answer and explanation

Answer: A · Worked explanation

Electromotive force is energy per unit charge, so its unit is joules per coulomb, J C−1\mathrm{J\,C^{-1}}JC−1. The unit C s−1\mathrm{C\,s^{-1}}Cs−1 is the ampere, which measures current. The unit J s−1\mathrm{J\,s^{-1}}Js−1 is the watt, which measures power. The unit V A−1\mathrm{V\,A^{-1}}VA−1 is the ohm, which measures resistance.
3

Part 3 of 5: Terminal potential difference falls as current increases

Now draw a graph of VVV against III for a source. The lost volts grow with the current, so the graph slopes downwards. Rearranging gives V=−rI+εV=-rI+\varepsilonV=−rI+ε. This has the form y=mx+cy=mx+cy=mx+c, so the graph is a straight line.

The line crosses the VVV axis at ε\varepsilonε. Its gradient is −r-r−r, so a steeper line means a larger internal resistance. It reaches zero p.d. at the largest possible current, I=εrI=\frac{\varepsilon}{r}I=rε​. With no internal resistance, the line would be horizontal. The largest current is reached when the external resistance is zero.

Figure 1. The line falls steadily as current rises. It meets the vertical axis at the EMF, and its gradient is the negative of the internal resistance.

Worked example

Terminal p.d. of a cell

A cell has ε=1.50 V\varepsilon=1.50\,\mathrm{V}ε=1.50V and r=0.50 Ωr=0.50\,\Omegar=0.50Ω. It is connected to a 2.5 Ω2.5\,\Omega2.5Ω resistor. Calculate the current and the terminal p.d.
  1. 1
    Use ε=I(R+r)\varepsilon=I(R+r)ε=I(R+r), so I=εR+rI=\frac{\varepsilon}{R+r}I=R+rε​.
  2. 2
    Substitute: I=1.50 V2.5 Ω+0.50 Ω=0.50 AI=\frac{1.50\,\mathrm{V}}{2.5\,\Omega+0.50\,\Omega}=0.50\,\mathrm{A}I=2.5Ω+0.50Ω1.50V​=0.50A.
  3. 3
    Lost volts: Ir=0.50 A×0.50 Ω=0.25 VIr=0.50\,\mathrm{A}\times0.50\,\Omega=0.25\,\mathrm{V}Ir=0.50A×0.50Ω=0.25V.
  4. 4
    Terminal p.d.: V=ε−Ir=1.50 V−0.25 V=1.25 VV=\varepsilon-Ir=1.50\,\mathrm{V}-0.25\,\mathrm{V}=1.25\,\mathrm{V}V=ε−Ir=1.50V−0.25V=1.25V.

Answer: The current is 0.50 A and the terminal p.d. is 1.25 V.

Part 3 done

4

Part 4 of 5: A variable resistor lets us measure EMF and internal resistance

To measure ε\varepsilonε and rrr, connect the cell in series with an ammeter, a switch and a variable resistor. Place a voltmeter across the cell’s terminals.

  • Set the variable resistor to its largest value and close the switch.
  • Record the current III and the terminal p.d. VVV.
  • Reduce the resistance a little and record both again.
  • Repeat for six or more readings, opening the switch between them.

Plot VVV on the vertical axis against III on the horizontal axis. Draw a best-fit straight line. The vertical intercept gives ε\varepsilonε, and the gradient gives −r-r−r.

Exam tip

Open the switch between readings. A continuous current warms the cell and can change its internal resistance.

Part 4 done

Quick check

One question on the part you just read

Easy

Identify the correct equation for the terminal p.d. VVV of a source of EMF ε\varepsilonε and internal resistance rrr supplying a current III.
Show answer and explanation

Answer: C · Worked explanation

The lost volts IrIrIr are subtracted from the EMF, so V=ε−IrV=\varepsilon-IrV=ε−Ir. The version with a plus sign would give a terminal p.d. larger than the EMF, which cannot happen because energy is lost inside the source. The quantity IrIrIr is a p.d., so it cannot be Ir\frac{I}{r}rI​.
5

Part 5 of 5: Internal resistance limits the current a source can supply

A high internal resistance wastes more energy inside the source. The lost volts rise with the current, so the terminal p.d. falls and the source heats up. The energy wasted per second inside the source is I2rI^2rI2r.

A car battery must supply a very large current to start an engine. Its internal resistance is therefore very small. Little p.d. is lost, so the terminal p.d. stays close to the EMF.

A voltmeter of very high resistance across the terminals draws almost no current. It reads close to the EMF, because IrIrIr is then almost zero.

Note read

Check your recall[14 marks]

5 written questions. Answer each one in your head or on paper, then open the mark scheme.

  1. 1.State[2 marks]

    State what is meant by the electromotive force of a source.

    Show mark schemeHide mark scheme

    Model answer

    The electromotive force is the energy supplied by the source per unit charge. It is measured in volts.

    • 1 mark for stating that it is the energy supplied by the source
    • 1 mark for stating that this is per unit charge, with the unit volt
  2. 2.Calculate[4 marks]

    Calculate the current and the terminal p.d. when a cell of EMF 1.5 V and internal resistance 0.40 Ω0.40\,\Omega0.40Ω is connected to a 2.6 Ω2.6\,\Omega2.6Ω resistor.

    Show mark schemeHide mark scheme

    Model answer

    I=εR+r=1.52.6+0.40=0.50 AI=\frac{\varepsilon}{R+r}=\frac{1.5}{2.6+0.40}=0.50\,\mathrm{A}I=R+rε​=2.6+0.401.5​=0.50A. V=IR=0.50×2.6=1.3 VV=IR=0.50\times2.6=1.3\,\mathrm{V}V=IR=0.50×2.6=1.3V, which agrees with ε−Ir=1.5−0.20=1.3 V\varepsilon-Ir=1.5-0.20=1.3\,\mathrm{V}ε−Ir=1.5−0.20=1.3V.

    • 1 mark for using ε=I(R+r)\varepsilon=I(R+r)ε=I(R+r)
    • 1 mark for obtaining a current of 0.50 A
    • 1 mark for using V=ε−IrV=\varepsilon-IrV=ε−Ir or V=IRV=IRV=IR
    • 1 mark for obtaining a terminal p.d. of 1.3 V
  3. 3.Explain[3 marks]

    Explain why the terminal p.d. of a cell is less than its EMF when the cell supplies a current.

    Show mark schemeHide mark scheme

    Model answer

    Energy is transferred inside the cell as charge passes through its internal resistance. The p.d. across the internal resistance is IrIrIr, the lost volts. Less energy per coulomb reaches the external circuit, so V=ε−IrV=\varepsilon-IrV=ε−Ir.

    • 1 mark for stating that the cell has internal resistance
    • 1 mark for stating that there is a p.d. IrIrIr across the internal resistance
    • 1 mark for concluding that V=ε−IrV=\varepsilon-IrV=ε−Ir, so the terminal p.d. is less than the EMF
  4. 4.Describe[3 marks]

    Describe how the EMF and the internal resistance of a cell can be found from a graph of terminal p.d. against current.

    Show mark schemeHide mark scheme

    Model answer

    Plot terminal p.d. on the vertical axis against current on the horizontal axis and draw a best-fit line. The vertical intercept gives the EMF. The gradient is the negative of the internal resistance.

    • 1 mark for plotting terminal p.d. against current and drawing a best-fit straight line
    • 1 mark for stating that the vertical intercept is the EMF
    • 1 mark for stating that the gradient is the negative of the internal resistance
  5. 5.Suggest[2 marks]

    Suggest why a car battery needs a very small internal resistance.

    Show mark schemeHide mark scheme

    Model answer

    The starter motor needs a very large current. With a small internal resistance, the lost volts are small, so the terminal p.d. stays close to the EMF.

    • 1 mark for stating that a very large current is needed
    • 1 mark for linking small internal resistance to small lost volts, so the terminal p.d. stays close to the EMF

Practice this topic

10 quick-fire multiple-choice questions, easy to hard. Tap an answer to see if you're right and the worked explanation. (The written questions with mark schemes are under “Check your recall” above.)

0 right0 of 10 answered

Includes the 2 quick checks in the note above.

3.

Easy·Identify[1 mark]

A voltmeter of very high resistance is connected across a cell that supplies no other circuit. It reads 1.5 V. Identify what this reading is closest to.
Show answer and explanation

Answer: B · Worked explanation

The voltmeter draws almost no current, so the lost volts IrIrIr are almost zero. The terminal p.d. is then almost equal to the EMF. The lost volts and the p.d. across the internal resistance are both close to zero here. A current is measured in amperes, not volts.
4.

Medium·Calculate[1 mark]

A cell of EMF 6.0 V and internal resistance 1.0 Ω1.0\,\Omega1.0Ω supplies a current of 2.0 A. Calculate the terminal p.d.
Show answer and explanation

Answer: A · Worked explanation

The lost volts are Ir=2.0×1.0=2.0 VIr=2.0\times1.0=2.0\,\mathrm{V}Ir=2.0×1.0=2.0V. Then V=ε−Ir=6.0 V−2.0 V=4.0 VV=\varepsilon-Ir=6.0\,\mathrm{V}-2.0\,\mathrm{V}=4.0\,\mathrm{V}V=ε−Ir=6.0V−2.0V=4.0V. The value 8.0 V comes from adding the lost volts instead of subtracting them. The value 2.0 V is the lost volts themselves. The value 6.0 V is the EMF, which applies only when no current flows.
5.

Medium·Calculate[2 marks]

A cell has an EMF of 9.0 V. When it supplies a current of 1.5 A, its terminal p.d. is 8.4 V. Calculate its internal resistance.
Show answer and explanation

Answer: B · Worked explanation

The lost volts are 9.0−8.4=0.60 V9.0-8.4=0.60\,\mathrm{V}9.0−8.4=0.60V. Then r=0.60 V1.5 A=0.40 Ωr=\frac{0.60\,\mathrm{V}}{1.5\,\mathrm{A}}=0.40\,\Omegar=1.5A0.60V​=0.40Ω. The value 0.60 Ω0.60\,\Omega0.60Ω comes from forgetting to divide by the current. The value 5.6 Ω5.6\,\Omega5.6Ω is the resistance of the external circuit, 8.41.5\frac{8.4}{1.5}1.58.4​, and 6.0 Ω6.0\,\Omega6.0Ω is the total resistance of the whole circuit, 9.01.5\frac{9.0}{1.5}1.59.0​.
6.

Medium·Determine[2 marks]

A graph of terminal p.d. against current for a cell is a straight line. It passes through 1.80 V at zero current and 0.60 V at 2.0 A. Determine the internal resistance of the cell.
Show answer and explanation

Answer: C · Worked explanation

The gradient is 0.60−1.802.0=−0.60 Ω\frac{0.60-1.80}{2.0}=-0.60\,\Omega2.00.60−1.80​=−0.60Ω, and the gradient equals −r-r−r. So r=0.60 Ωr=0.60\,\Omegar=0.60Ω. The value 0.90 Ω0.90\,\Omega0.90Ω comes from dividing the EMF by the current, which would be the internal resistance only if the terminal p.d. fell to zero at 2.0 A. The value 0.30 Ω0.30\,\Omega0.30Ω divides the final p.d. by the current.
7.

Medium·Identify[1 mark]

A student plots terminal p.d. on the vertical axis against current on the horizontal axis for a cell. Identify what the gradient of the best-fit line represents.
Show answer and explanation

Answer: D · Worked explanation

From V=−rI+εV=-rI+\varepsilonV=−rI+ε, the gradient is −r-r−r, so it is the negative of the internal resistance. The vertical intercept gives the EMF. Quoting a positive value for the gradient ignores the fact that the terminal p.d. falls as the current rises. The largest current is found where the line meets the horizontal axis.
8.

Hard·Determine[2 marks]

A cell has an EMF of 1.6 V and an internal resistance of 0.80 Ω0.80\,\Omega0.80Ω. It is connected to a resistor RRR, and the terminal p.d. is 1.2 V. Determine RRR.
Show answer and explanation

Answer: B · Worked explanation

The lost volts are 1.6−1.2=0.40 V1.6-1.2=0.40\,\mathrm{V}1.6−1.2=0.40V, so I=0.400.80=0.50 AI=\frac{0.40}{0.80}=0.50\,\mathrm{A}I=0.800.40​=0.50A. Then R=VI=1.20.50=2.4 ΩR=\frac{V}{I}=\frac{1.2}{0.50}=2.4\,\OmegaR=IV​=0.501.2​=2.4Ω. The value 3.2 Ω3.2\,\Omega3.2Ω is εI\frac{\varepsilon}{I}Iε​, which is the total resistance R+rR+rR+r and not RRR alone. The value 4.0 Ω4.0\,\Omega4.0Ω comes from dividing the EMF by the lost volts, which treats a p.d. as a current. Always check that the answer is less than the total resistance.
9.

Hard·Determine[2 marks]

A cell has an EMF of 4.5 V and an internal resistance of 1.5 Ω1.5\,\Omega1.5Ω. It is connected to a 1.5 Ω1.5\,\Omega1.5Ω resistor. The resistor is replaced by a 3.0 Ω3.0\,\Omega3.0Ω resistor. Determine the change in the terminal p.d.
Show answer and explanation

Answer: A · Worked explanation

With 1.5 Ω1.5\,\Omega1.5Ω, I=4.53.0=1.5 AI=\frac{4.5}{3.0}=1.5\,\mathrm{A}I=3.04.5​=1.5A and V=1.5×1.5=2.25 VV=1.5\times1.5=2.25\,\mathrm{V}V=1.5×1.5=2.25V. With 3.0 Ω3.0\,\Omega3.0Ω, I=4.54.5=1.0 AI=\frac{4.5}{4.5}=1.0\,\mathrm{A}I=4.54.5​=1.0A and V=3.0 VV=3.0\,\mathrm{V}V=3.0V. The p.d. rises by 0.75 V0.75\,\mathrm{V}0.75V. A fall would suggest that a smaller current lowers the p.d., but the lost volts IrIrIr fall too, so more of the EMF reaches the resistor. An increase of 1.5 V is too large.
10.

Hard·Identify[2 marks]

A cell supplies a current to an external circuit. Identify the correct statement.
Show answer and explanation

Answer: A · Worked explanation

The EMF is the energy per coulomb supplied. The terminal p.d. is the part delivered to the external circuit. The rest, ε−V=Ir\varepsilon-V=Irε−V=Ir, is transferred inside the cell. The EMF is fixed for a given source, and the internal resistance is treated as constant. The terminal p.d. equals the EMF only when no current flows.

Keep going

Next topic3.6.1.1 Circular motionPrevious topic3.5.1.5 Potential dividers

More in Section 3.5 · Electricity

  1. 3.5.1.1Basics of electricityNotes · 10 questions
  2. 3.5.1.2Current–voltage characteristicsNotes · 10 questions
  3. 3.5.1.3ResistivityNotes · 10 questions
  4. 3.5.1.4CircuitsNotes · 10 questions
  5. 3.5.1.5Potential dividersNotes · 10 questions
  6. 3.5.1.6EMF and internal resistanceNotes · 10 questions

All AQA A-level Physics topics →

Draft: written by Scribe and checked automatically, not yet by a subject reviewer.

Practice questions are original, written by Scribe and checked automatically for correctness.

Topic codes follow the official numbering. Not endorsed by AQA or any exam board.

On this page

0/5 read

  1. 1A source gives energy to each coulomb of charge
  2. 2Internal resistance causes energy loss inside the source
  3. 3Terminal potential difference falls as current increases
  4. 4A variable resistor lets us measure EMF and internal resistance
  5. 5Internal resistance limits the current a source can supply
  6. Check your recall
  7. Practice: 10 questions
All coursesScribeHow it worksPricingPrivacyTerms

Notes and questions are written by Scribe in our own words. Topic codes follow the official course numbering so you can find your place. Not produced or endorsed by the IB, College Board, AQA, OCR, Pearson Edexcel or any exam board.

© 2026 Scribe

Terminal p.d. against current

Terminal p.d. V (V)00.511.522.5300.511.5Current I (A)
  • V = ε − Ir
  • Worked example